Yamaha P-300 Návod k obsluze

Značka: Yamaha

Modelka: P-300

Kategorie: Syntetizér

Typ: Návod k obsluze

Tato příručka je také vhodná pro

NS-P300

HOME CINEMA SPEAKER PACKAGE

SYSTEME D ’ENCEINTES HOME CINEMA

NS-P300

Active Servo

Technology

U C A

CONTENTS

SAFETY INSTRUCTIONS ...............................2

PROFILE OF THIS SYSTEM .........................3

CAUTION ........................................................4

SUPPLIED ACCESSORIES ............................4

SETTING UP THE SPEAKERS ......................5

CONNECTIONS ..............................................8

USING THE SUBWOOFER (SW-P30) ..........12

CONTROLS AND THEIR FUNCTIONS .....12

ADJUSTMENT BEFORE USING THE

SUBWOOFER ............................................13

ACTIVE SERVO TECHNOLOGY

(for SW-P30)................................................14

TROUBLESHOOTING (for SW-P30) ............15

SPECIFICATIONS .........................................16

TABLES DES MATIERES

PRESENTATION DE CE SYSTEME ............17

ACCESSOIRES FOURNIS ...........................17

PRECAUTIONS D’USAGE ...........................18

DISPOSITION DES ENCEINTES .................19

CONNEXIONS ..............................................22

UTILISATION DU SUBWOOFER

(SW-P30)........................................................26

LES COMMANDES ET LEURS

FONCTIONS ..............................................26

REGLAGE AVANT D’UTILISER LE

SUBWOOFER ............................................27

ACTIVE SERVO TECHNOLOGY

(pour SW-P30).............................................28

EN CAS DE DIFFICULTE (pour SW-P30) .....29

CARACTERISTIQUES TECHNIQUES .........30

OWNER’S MANUAL

Thank you for selecting this YAMAHA.

MODE D’EMPLOI

Nous vous remercions pour avoir porté votre

choix sur ce YAMAHA.

1 Read Instructions – All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the manufacturer.

6A A unit and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause

the unit and

cart combination to overturn.

7 Wall or Ceiling Mounting – The unit

should be mounted to a wall or ceiling only as

recommended by the manufacturer.

8 Ventilation – The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be situated

on a bed, sofa, rug, or similar surface, that may block the

ventilation openings; or placed in a built-in installation,

such as a bookcase or cabinet that may impede the flow

of air through the ventilation openings.

9 Heat – The unit should be situated away from heat

sources such as radiators, stoves, or other appliances

that produce heat.

10 Power Sources – The unit should be connected to a

power supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be serviced

by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or

exhibits a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the unit

beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located

away from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

SAFETY INSTRUCTIONS

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead

symbol, within an equilateral triangle,

is intended to alert you to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert

you to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the

appliance.

CAUTION

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

IMPORTANT

Please record the serial number of your unit

in the space below.

Model:

Serial No.:

The serial number is located on the rear of

the unit.

Retain this Owner’s Manual in a safe place

for future reference.

English

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions.

Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class “B” digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try

to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

FCC INFORMATION (for US customers only)

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the

sound come through loud and clear without annoying blaring

or distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

We Want You Listening For A Lifetime

“NS-P300” is the package number which includes the YAMAHA speaker system NS-M103, NS-C103, NS-E103 and SW-P30.

This speaker package system is designed for use in a multi-channel audio system, for example a home theater system, so the

package includes a pair of main speakers (NS-M103), a center speaker (NS-C103), a pair of effect speakers (NS-E103) and a

subwoofer system (SW-P30).

PROFILE OF THIS SYSTEM

2-way acoustic-suspension speaker system

2-way 3-speaker bass-reflex speaker system

Full-range bass-reflex speaker system

Active Servo Processing Subwoofer System with a

built-in power amplifier

•

This subwoofer system employs YAMAHA Active Servo

Technology which YAMAHA have developed for

reproducing higher quality super-bass sound. (Refer to page

14 for details on Active Servo Technology.)

•

This unit can be added easily to your existing audio system

by connecting to either the speaker terminals or the line

output (pin jack) terminals of the amplifier.

•

The HIGH CUT switch provides you with two positions

(HIGH and LOW) to adjust the tone balance between the

subwoofer and the main speakers.

•

The AUTO STANDBY switch saves you the trouble of

setting the POWER switch to the ON or OFF position.

●

To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

●

Install the speakers in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration, dust,

moisture and cold. Avoid sources of humming

(transformers, motors).

●

To prevent fire or electrical shock, do not expose the

speakers to rain or water.

●

To prevent the enclosure from warping or discoloring, do not

place the speakers where it will be exposed to direct

sunlight or excessive humidity.

●

Do not place the speakers where it is liable to be knocked

over or struck by falling objects. Stable placement will also

ensure better sound performance.

●

Placing the speakers on the same shelf or rack as the

turntable can result in feedback.

●

Any time you note distortion, reduce the volume control on

your amplifier to a lower setting. Never allow your amplifier

to be driven into “clipping”. Otherwise the speakers may be

damaged.

●

When using an amplifier with a rated output power higher

than the nominal input power of the speakers, care should

be taken never to exceed the speakers’ maximum input.

●

As these speakers contain strong magnets (though all of

them are magnetically shielded types), avoid placing

watches, magnetic tapes, etc. near them. Also, placing the

speakers near a TV set may impair picture color. If this

happens, move the speakers away from TV set.

●

Do not attempt to clean the speakers with chemical

solvents; this might damage the finish. Use a clean, dry

cloth.

●

Secure placement or installation is the owner’s

responsibility.

YAMAHA shall not be liable for any accident caused by

improper placement or installation of the speakers.

For canadian customers

To prevent electric shock, match wide blade of plug to wide

slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES–003.

●

Never open the cabinet. If something drops into the set,

contact your dealer.

●

Do not use force on switches, controls or connection cords.

When moving the unit, first disconnect the power plug and

the cords connected to other equipment. Never pull the

cords itself.

●

Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that

the unit is faulty.

●

When not planning to use this unit for long periods of time

(ie., vacation, etc.), disconnect the AC power plug from the

wall outlet.

●

To prevent lightning damage, disconnect the AC power plug

when there is an electrical storm.

●

Since this unit has a built-in power amplifier, heat will radiate

from the rear panel. Therefore, place the unit apart from the

walls, allowing enough space above, behind and on the both

sides of the unit to prevent fire and damage. Also, do not

position with the rear panel facing down on the floor or other

surface.

Be sure to allow a space of at least 20 cm above, behind

and on the both sides of the unit.

●

Super-bass frequencies reproduced by this unit may cause

a turntable to generate a howling sound. In such a case,

move this unit away from the turntable.

●

If you hear distortion (i.e., unnatural, intermittent “rapping” or

“hammering” sounds) coming from this unit, reduce the

volume level. Extremely loud playing of a movie

soundtrack’s low frequency, bass-heavy sounds or similarly

loud popular music passages can damage this speaker

system.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode.

In this state, this unit is designed to consume a very small

quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

After unpacking, check that the following parts are contained.

Speaker cords Velcro strips (for NS-C103)

SUPPLIED ACCESSORIES

English

Before you make connections, place all speakers in their proper positions respectively. The positioning of speakers is important,

because it controls the whole sound quality of this system.

Position the speakers based on your listening position by following instructions in this section.

Speaker configuration

This system employs a 6 speaker configuration: 2 main

speakers, 2 effect speakers, a center speaker and a

subwoofer.

The main speakers are used for main source sound. The effect

speakers are used for effect and surround sounds, and the

center speaker is for center sounds (dialog etc.). The

subwoofer is for reinforcing low frequencies on your audio

system.

Placing speakers

Main speakers: On both sides of the TV and almost the

same height as the TV.

Effect speakers: Behind your listening position, facing

slightly inward. Nearly 1.8 m (approx. 6

feet) up from the floor.

Center speaker: Precisely between the main speakers.

Subwoofer: The position of the subwoofer is not so

critical because low bass tones are not

highly directional.

Refer to “Placing the subwoofer” shown

below for a recommended positioning of

the subwoofer.

Main L Center Main R

Effect L Effect R

Subwoofer

TV set

Subwoofer

Effect L

Effect R

Main L

Main R

Center

SETTING UP THE SPEAKERS

It is recommended to place the subwoofer on the outside of

either the right or the left main speaker. (See fig. .) The

placement shown in fig. is also possible, however, if the

subwoofer system is placed directly facing the wall, the bass

effect may die because the sound from it and the sound

reflected by the wall may cancel. To prevent this, face the

subwoofer system obliquely to the wall as shown in fig. .

Note

There may be a case that you cannot obtain enough super-

bass sounds from this unit when listening at the middle of the

room. This is because “standing waves” have been developed

between two parallel walls and they cancel the bass sounds.

In such a case, face the subwoofer obliquely to the wall. It also

may be necessary to break up the parallel surfaces by placing

bookshelves etc. along the walls.

■ Placing the subwoofer

( : subwoofer, : main speaker)

■ Mounting the center speaker

Place the center speaker on the TV, on the floor under the TV

or in the TV rack so that it is stabilized.

When placing the speaker on top of the TV, to prevent the

speaker from falling down, put the provided velcro strips at two

points on both bottom of the speaker and top of the TV.

Notes

• Do not place the speaker on top of the TV whose area is

smaller than the bottom area of the speaker. If placed,

the speaker may drop down and that injures you.

• Though this speaker is a magnetically shielded type,

there may be some influence on a TV picture depending

on the type of TV or the placement of the speaker. In

such a case, place the speaker apart from the TV so that

there is no influence on TV picture.

Velcro strip

TV set

Speaker on TV

Speaker inside

TV rack

■ Adjusting the main speakers

Adjusting the angle of the main speakers

The angle of the main speakers can be adjusted according to

the placement of them.

1. Loosen the screw at the

bottom of the speaker

stand as figured below.

2. Slide the speaker on the

stand until the desired

angle is obtainted, and

then tighten the screw.

Removing the front cover

The front cover is fastened to the enclosure at four points, and

can be removed if desired. To remove the cover, hold both

sides and slowly pull straight away from the speaker. To

reattach, line up the four pegs on the inside surface of the

cover with the four corresponding holes on the speaker and

push gently.

Tighten

Loosen

English

■ Mounting the effect speakers

Mount the effect speakers on a shelf, rack or floor, or hang

them on the wall.

To mount the effect speakers on a wall

Mount the speakers in either of the two configurations shown in

the following figures by using the holes provided on the

speakers’ rear panels.

Fasten wood screws onto a firm wall or wall support as shown

in the following figure, and set the mounting holes on the

protruding screws.

* Make sure that the screw is caught securely at a narrow part

of the hole.

For the upright mounting, only one hole is provided.

As for the side-long mounting, two holes are provided. Be sure

to use these two holes as a set.

WARNING:

• Each speaker weighs 1.4 kg (3 lbs. 1 oz.). Do not mount

them on thin plywood or soft wall surface material. If

mounted, the screws may come out of the flimsy surface

and the speakers may fall down. That damages the

speakers or causes personal injury.

• Do not install the speakers to wall with nails, adhesives,

or other unsound hardware. Long-term use and

vibrations may cause them to fall down.

• To avoid accidents resulting from tripping over loose

speaker cords, fix them to the wall.

Upright mounting Side-long mounting

60mm

(2-3/8”)

Diam. 4–5 mm

(3/16”)

Min.

12 mm

(1/2”)

Wood screw

(Available at a

hardware store)

Wall or

wall support

4–5 mm (3/16”)

For upright

mounting

For side-long

mounting

For side-long

mounting

• Connect the speakers to the speaker output terminals of

your amplifier with the provided speaker cords.

• Connect the speakers making sure not to reverse the

polarity (+, –). Connect the (+) terminals on both the

amplifier and the speakers using one side of the cord.

Connect the (–) terminals on both components using the

other side of the cord. If one speaker is connected with

reversed polarity, the sound will be unnatural and lack bass.

• For the main and effect speakers only

, connect one

speaker to the left (marked L) terminals of your amplifier,

and another speaker to the right (marked R) terminals.

• The subwoofer can be connected to either the speaker

output terminals or the line output (pin jack) terminals of the

amplifier. Choose one of the ways shown in this section

which is suitable for your audio system. Also, refer to the

owner’s manual for your component to be connected to this

unit.

CONNECTIONS

REAR REARCENTER

CAUTION

SEE INSTRUCTION MANUAL FOR CORRECT SETTING.

MAIN

SPEAKERS

REAR

SINGLE

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

INPUT2

VOLUME

HIGH CUT

AUTO

STANDBY

RED

GREEN

OFF

LOW

HIGH

010

OFF

POWER

LOW

HIGH

Subwoofer

Effect speaker

Center speaker

Effect speaker

Right

Main speakers

Right Left

Left

Amplifier

To AC outlet

Note

This diagram shows an example of connecting speakers to an amplifier which has two sets of main speaker output terminals. If you

select this connecting way, you must operate the amplifier so that both sets of main speaker output terminals output signals.

This speaker system can also be connected to the amplifier in other ways depending on the type of amplifier. Refer to pages 10 to

11 for details.

Never plug in the subwoofer and other audio/video components until all connections are completed.

English

For connections, keep the speaker cords as short as possible.

Do not bundle or roll up an excess of the cords. If the

connections are faulty, no sound will be heard from the

speakers.

How to Connect:

➀ Press and hold the terminal’s tab, as shown in the figure.

➁ Insert the bare wire end properly into the terminal hole.

[Remove approx. 10 mm (3/8”) insulation from the speaker

cord.]

➂ Remove your finger from the tab to allow it to lock snugly

on the cord’s wire end.

➃ Test the security of the connection by pulling lightly on the

cord at the terminal.

Note

Do not let the bare speaker wires touch each other as this

could damage the speaker or the amplifier, or both of

them.

Center speaker

Red: positive (+)

Black: negative (–)

Effect speakers

Red: positive (+)

Black: negative (–)

Subwoofer (INPUT1/OUTPUT terminals)

Red: positive (+)

Black: negative (–)

Good No Good

How to connect speaker cords to the input and output terminals of the speakers

Main speakers

How to Connect:

Red: positive (+)

Black: negative (–)

➀Loosen the knob.

➁Insert the bare wire.

[Remove approx. 10 mm

(3/8”) insulation from the

speaker cord.]

➂Tighten the knob and

secure the wire.

Note

Do not let the bare speaker wires touch each other as this

could damage the speaker or the amplifier, or both of

them.

* Banana Plug connections are also possible. Simply insert

the Banana Plug connector into the corresponding terminal.

10 mm

➁

➀

➁

➂

➀

➁

➀

If your amplifier has only one set of main speaker output terminals

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

INPUT2

HIGH CUT

AUTO

STANDBY

RED

GREEN

OFF

LOW

HIGH

OFF

POWER

LOW

HIGH

VOLUME

010

Amplifier

To AC outlet

Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals

of the subwoofer to the main speakers.

Subwoofer

Main speaker Main speaker

Right Left

English

• To connect with a YAMAHA DSP amplifier (or AV receiver),

connect the LOW PASS (or SUBWOOFER etc.) terminal on

the rear of the DSP amplifier (or AV receiver) to either the

left (L) or right (R) INPUT2 terminal of the subwoofer.

• To connect the subwoofer to the SPLIT SUBWOOFER

terminals on the rear of the DSP amplifier, connect them to

both of the left (L) and right (R) INPUT2 terminals of the

subwoofer.

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

INPUT2

HIGH CUT

AUTO

STANDBY

RED

GREEN

OFF

LOW

HIGH

POWER

LOW

HIGH

SPLIT SUBWOOFER

LOW PASS

(SUBWOOFER)

OFF

INPUT2

VOLUME

010

Pin plug cords

Amplifier

To AC outlet

To connect the subwoofer to line output (pin jack) terminals of the amplifier

Notes

• Some amplifiers have line output terminals labeled PRE

OUT. When you connect the subwoofer to the PRE OUT

terminals of the amplifier, make sure that the amplifier has

at least two sets of PRE OUT terminals. If the amplifier has

only one set of PRE OUT terminals, do not connect the

subwoofer to the PRE OUT terminals. Connect the

subwoofer to the speaker output terminls of the amplifier.

(Refer to pages 8 and 10.)

• When connecting to a monaural line output terminal of the

amplifier, connect to either the left or right INPUT2 terminal.

• When connected to line output terminals of the amplifier,

other speakers should not be connected to the OUTPUT

terminals on the rear panel of the subwoofer. If connected,

they will not produce sound.

Subwoofer

Main speaker Main speaker

Left Right

Connect the main speakers to the speaker output terminals of the amplifier.

OUTPUT (TO SPEAKERS) terminals

Can be used for connections with the main speakers.

These terminals output signals sent from the amplifier to

the main speakers directly.

2 INPUT1 (FROM AMPLIFIER) terminals

Used to connect this unit with the speaker terminals of the

amplifier.

3 INPUT2 terminals

Used to input line level signals from the amplifier.

4 VOLUME control

Adjusts the volume level.

5 HIGH CUT (HIGH/LOW) switch

Selects the high frequency cut off point.

Normally, set to LOW, however, you may set to HIGH if

necessary. Refer to “Note about setting the HIGH CUT

switch” on page 13.

6 AUTO STANDBY (HIGH/LOW/OFF) switch

By setting this switch to the HIGH or LOW position, this

unit’s automatic power-switching function operates as

described right. If you do not need this function, set to the

OFF position.

* Make sure to change the setting of this switch only when

this unit is in the standby mode.

7 Power indicator

Lights in green when the POWER switch set to the ON

position, and goes off when set to the OFF position.

* Standby mode

If the POWER switch is set to the ON position and the

AUTO STANDBY switch is set to the HIGH or LOW

position, this indicator lights in red when no signal is

input to this unit.

8 POWER switch

Set this switch to the ON position to turn on the power of

this unit. When the power of this unit is on, the power

indicator above the POWER switch lights in green. Set

this switch to the OFF position to turn off the power of this

unit.

Automatic power-switching function

When you play a source, the power of this unit turns on

automatically by sensing audio signals input to this unit.

This unit turns into the standby mode automatically if the

source being played is stopped or the input signal is cut off

for several minutes.

This function will operate by sensing a certain level of low

frequency input signal. Its sensitivity is high in the HIGH

position and low in the LOW position of the AUTO

STANDBY switch. Set this switch to whichever position

you like. In the HIGH position, the power will turn on even

with a low level of input signal, but on the other hand this

unit may not turn into the standby mode when there is an

input signal even if its level is extremely low.

* There may be a case that the power turns on

unexpectedly by sensing noise from other appliances. If

it occurs, set the AUTO STANDBY switch to the OFF or

LOW position.

* The level of low frequency input signal differs with each

source, and each different part on the same source. So,

this function may not operate properly depending on

some sources.

This function is available only when the power of this

unit is on (by setting the POWER switch (

8) to “ON”).

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

INPUT2

HIGH CUT

AUTO

STANDBY

RED

GREEN

OFF

LOW

HIGH

OFF

POWER

LOW

HIGH

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

INPUT2

HIGH CUT

AUTO

STANDBY

RED

GREEN

OFF

LOW

HIGH

LOW

HIGH

OFF

POWER

VOLUME

010

VOLUME

010

CONTROLS AND THEIR FUNCTIONS

Rear panel

USING THE SUBWOOFER (SW-P30)

English

1 Set the VOLUME control to minimum.

2 Turn on the power supply to all the components.

3 Play any source and adjust the amplifier’s volume control

to the desired listening level.

4 Increase the volume gradually to adjust the volume

balance between this unit and the main speakers.

5 If necessary, you may set the HIGH CUT switch to the

HIGH position.

Notes

•

Once the volume balance between the subwoofer and the

main speakers is adjusted, you can adjust the volume of

your whole sound system by using only the amplifier’s

volume control.

However, if you change the main speakers NS-M103 to

others, you must make this adjustment again.

•

For adjusting the VOLUME control and the HIGH CUT

switch, refer to “FREQUENCY CHARACTERISTICS” shown

below.

Note about setting the HIGH CUT switch

This system is designed so that the optimum tone balance

between the subwoofer and the main speakers is obtained

when this switch is set to the LOW position. However, the tone

balance may change depending on the room size, the distance

from the subwoofer to the main speakers, and so on.

So, if necessary, switch it to the HIGH position.

ADJUSTMENT BEFORE USING THE SUBWOOFER

Before using the subwoofer, make an adjustment on the subwoofer to obtain the optimum volume and tone balance between the

subwoofer and the main speakers by following the procedures shown below.

INPUT2

HIGH CUT

AUTO

STANDBY

RED

GREEN

OFF

LOW

HIGH

LOW

HIGH

OUTPUT

TO SPEAKERS

INPUT1

FROM AMPLIFIER

INPUT2

HIGH CUT

AUTO

STANDBY

RED

GREEN

OFF

LOW

HIGH

OFF

POWER

LOW

HIGH

VOLUME

010

VOLUME

010

1, 4

Fig. 1 shows the frequency characteristics of the subwoofer

with each position (HIGH/LOW) of the HIGH CUT switch.

Fig. 2 shows the optimum volume level with the HIGH CUT

switch at the LOW position and its frequency characteristics

when this subwoofer is combined with NS-M103 (main

speakers).

■ FREQUENCY CHARACTERISTICS

20 50 100 200 500Hz

10 0

HIGH CUT

LOW

HIGH CUT

HIGH

20 50 100 200 500Hz

10 0

SW-P30

NS-M103

HIGH CUT

LOW

HIGH

VOLUME

010

Fig. 1 Fig. 2

The theory of Active Servo Technology is based upon two

major factors, the Helmholtz resonator and negative-

impedance drive. Active Servo Processing speakers

reproduce the bass frequencies through an “air woofer”,

which is a port or opening in the speaker’s cabinet. This

opening is used instead of, and performs the functions of,

a woofer in a conventionally designed speaker system.

Thus, signals of low amplitude within the cabinet can,

according to the Helmholtz resonance theory, be output

from this opening as waves of great amplitude if the

design is such that the size of the opening and the volume

of the cabinet are in the correct proportion to satisfy a

certain ratio.

In order to accomplish this, moreover, the amplitudes

within the cabinet must be both precise and of sufficient

power because these amplitudes must overcome the

“load” presented by the air that exists within the cabinet.

Thus it is this problem that is resolved through the

employment of a design in which the amplifier functions to

supply special signals. If the electrical resistance of the voice

coil could be reduced to zero, the movement of the speaker

unit would become linear with respect to signal voltage, and,

to accomplish this, a special negative-impedance output-drive

amplifier for subtracting output impedance of the amplifier is

used.

By employing negative-impedance drive circuits, the amplifier

is able to generate precise, low-amplitude low-frequency

waves with superior damping characteristics, and these

waves are then radiated from the cabinet opening as high-

amplitude signals. The system can, therefore, by employing

the negative-impedance output drive amplifier and a speaker

cabinet with the Helmholtz resonator, reproduce an extremely

wide range of frequencies with amazing sound quality and

less distortion.

The features described above, then, are combined to be the

fundamental structure of the Active Servo Technology.

Signals of low amplitude

Air woofer

(Helmholtz resonator)

Negative-impedance

output drive

High-

amplitude

bass

sound

Signals

Active

Servo

Processing

Amplifier

Cabinet

Port

ACTIVE SERVO TECHNOLOGY (for SW-P30)

English

SYMPTOM

Power is not supplied even though the

POWER switch is set to the ON position.

No sound.

Sound level is too low.

This unit will not turn on automatically.

This unit turns into the standby mode

unexpectedly.

This unit turns on unexpectedly.

CAUSE

The power plug is not securely connected.

The VOLUME control is set to 0.

Speaker cords are not connected securely.

Speaker cords are connected incorrectly.

A source sound with few bass frequencies is

played.

It is influenced by standing waves.

The POWER switch is set to the OFF

position.

The AUTO STANDBY switch is set to the

OFF position.

The level of input signal is too low.

An influence of noise generated from

external equipment etc.

REMEDY

Connect it securely.

Turn the VOLUME control to right.

Connect them securely.

Connect them correctly, that is to say L (left)

to L, R (right) to R, “+” to “+” and “–” to “–”.

Play a source sound with bass frequencies.

Set the HIGH CUT switch to the “HIGH”

position.

Re-position the subwoofer or break up the

parallel surface by placing bookshelves etc.

along the walls.

Set the POWER switch to the ON position.

Set the AUTO STANDBY switch to the

“HIGH” or “LOW” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Set the AUTO STANDBY switch to the

“HIGH” position.

Move this unit farther away from such

equipment and/or change the position of

connected speaker cables.

Otherwise, set the AUTO STANDBY switch

to the “OFF” position.

If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple

measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and

contact your authorized YAMAHA dealer or service center for help.

TROUBLESHOOTING (for SW-P30)

NS-M103, NS-C103, NS-E103>

Type

<NS-M103>........2-way acoustic-suspension speaker system

Magnetic shielding type

<NS-C103>......2-way 3-speaker bass-reflex speaker system

Magnetic shielding type

<NS-E103>.................Full-range bass-reflex speaker system

Magnetic shielding type

Speaker Unit

<NS-M103>..................................12 cm (4-3/4”) cone woofer

2.2 cm (7/8”) semidome tweeter

<NS-C103>.............................8 cm (3-1/8”) cone speaker x 2

2.2 cm (7/8”) tweeter

<NS-E103>.............................10 cm (3-15/16”) cone speaker

Nominal Input Power

<NS-M103>......................................................................40W

<NS-C103>......................................................................40W

<NS-E103>.......................................................................25W

Maximum Input Power

<NS-M103>....................................................................120W

<NS-C103>....................................................................120W

<NS-E103>.......................................................................80W

Impedance......................................................................6 ohms

Frequency Response

<NS-M103>.......................................................65 Hz–20 kHz

<NS-C103>.......................................................65 Hz–20 kHz

<NS-E103>.......................................................70 Hz–20 kHz

Sensitivity

<NS-M103>............................................................90 dB/W

●

<NS-C103>............................................................89 dB/W

●

<NS-E103>............................................................90 dB/W

●

Dimensions (W x H x D)

<NS-M103>...............................170 mm x 255 mm x 187 mm

(6-11/16” x 10-1/16” x 7-3/8”)

<NS-C103>...............................435 mm x 100 mm x 230 mm

(17-1/8” x 4” x 9-1/16”)

<NS-E103>...............................180 mm x 220 mm x 101 mm

(7-1/16” x 8-11/16” x 4”)

Weight

<NS-M103>.......................................2.1 kg (4 lbs. 10 oz.) x 2

<NS-C103>...............................................2.0 kg (4 lbs. 6 oz.)

<NS-E103>..........................................1.4 kg (3 lbs. 1 oz.) x 2

<SW-P30>

Type......................Active Servo Processing Subwoofer System

Magnetic shielding type

Speaker Unit.................................16 cm (6-5/16”) cone woofer

Amplifier Output....................................................40W/4 ohms

High-Cut Filter

.................................Alternatives: 100 Hz, 200 Hz (–24 dB/oct.)

Impedance

INPUT1....................................................................4.7 k-ohms

INPUT2.....................................................................10 k-ohms

Frequency Response ..........................32 Hz–240 Hz (–10 dB)

Power Supply

U.S.A. and Canada models........................AC 120V, 60 Hz

Europe model..............................................AC 230V, 50 Hz

Australia model...........................................AC 240V, 50 Hz

General model ..................AC 110-120/220-240V, 50/60 Hz

Power Consumption..........................................................40W

Dimensions (W x H x D) .............210 mm x 350 mm x 312 mm

(8-1/4” x 13-3/4” x 12-5/16”)

Weight........................................................7.4 kg (16 lbs. 4 oz.)

* Please note that all specifications are subject to change

without notice.

SPECIFICATIONS

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

V260720Printed in China

Yamaha P-300 Návod k obsluze

Značka: Yamaha

Modelka: P-300

Kategorie: Syntetizér

Typ: Návod k obsluze

Tato příručka je také vhodná pro

NS-P300

Stáhnout PDF

zpráva

v jiných jazycích

polski: Yamaha P-300 Instrukcja obsługi
español: Yamaha P-300 El manual del propietario
italiano: Yamaha P-300 Manuale del proprietario
Deutsch: Yamaha P-300 Bedienungsanleitung
svenska: Yamaha P-300 Bruksanvisning
português: Yamaha P-300 Manual do proprietário
français: Yamaha P-300 Le manuel du propriétaire
Türkçe: Yamaha P-300 El kitabı
English: Yamaha P-300 Owner's manual
dansk: Yamaha P-300 Brugervejledning
русский: Yamaha P-300 Инструкция по применению
suomi: Yamaha P-300 Omistajan opas
Nederlands: Yamaha P-300 de handleiding
română: Yamaha P-300 Manualul proprietarului

Yamaha P-300 Návod k obsluze

Tato příručka je také vhodná pro

Yamaha P-300 Návod k obsluze

v jiných jazycích

Související papíry