Yamaha MG10XU Specifikace

Značka: Yamaha

Modelka: MG10XU

Kategorie: Audio mixéry

Typ: Specifikace

Tato příručka je také vhodná pro

MG10

General Specifications

0 dBu = 0.775 Vrms Output impedance of signal generator (Rs) = 150Ω

All level knobs are nominal if not specified.

Frequency Response Input to STEREO OUT

+0.5 dB/-1.0 dB (20 Hz to 48 kHz),

refer to the nominal output level @1 kHz, GAIN knob: Min

Total Harmonic Distortion

(THD+N)

Input to STEREO OUT

0.02 % @ +14 dBu (20 Hz to 20 kHz), GAIN knob: Min

0.003 % @ +24 dBu (1 kHz), GAIN knob: Min

Hum&Noise *1

(20 Hz to 20 kHz)

Equivalent Input Noise -128 dBu (Mono Input Channel, Rs: 150 Ω, GAIN knob: Max)

Residual Output Noise -102 dBu (STEREO OUT, STEREO LEVEL knob: Min)

Crosstalk (1 kHz) *2 -83 dB

Input Channels 10 channels: Mono [MIC/LINE]: 4, Stereo [LINE]: 3

Ouput Channels STEREO OUT: 2, PHONES: 1, MONITOR OUT: 1, AUX (FX) SEND: 1

Bus Stereo: 1, AUX (FX): 1

Input Channel Function

PAD CH1 – CH4 26 dB

HPF CH1 – CH4 80 Hz, 12 dB/oct

COMP CH1 – CH2

1-knob compressor

Threshold: +22 dBu to -8 dBu, Ratio:1:1 to 4:1,

Output level: 0 dB to 7 dB, Attack time: approx. 25 msec,

Release time: approx. 300 msec

CH1 – CH9/10 HIGH:

Gain: +15 dB/-15 dB, Frequency: 10 kHz shelving

CH1 – CH4 MID:

Gain: +15 dB/-15 dB, Frequency: 2.5 kHz peaking

CH1 – CH9/10 LOW:

Gain: +15 dB/-15 dB, Frequency: 100 Hz shelving

PEAK LED CH1 – CH4

LED turns on when post EQ signal reaches 3 dB below

clipping (+17 dBu)

Level Meter

Post STEREO LEVEL

Knob

2×7 -segment LED meter [PEAK (+17), +10, +6, 0, -6, -10, -20 dB]

Internal Digital Effect

(MG10XU)

SPX Algorithm 24 programs

USB Audio (MG10XU) 2 IN / 2 OUT

USB Audio Class 2.0 compliant

Sampling Frequency: Max 192 kHz, Bit Depth: 24-bit

Phantom Power Voltage +48 V

Power Supply Adaptor

PA-10 (AC 38 VCT, 0.62A, Cable length = 3.6 m)

or equivalent recommended by Yamaha

Power Consumption 22.9 W

Dimensions (W×H×D) 244 mm×71 mm×294 mm (9.6” × 2.8” × 11.6”)

Net Weight MG10XU: 2.1 kg (4.6 lbs.), MG10: 1.9 kg (4.1 lbs.)

Included Accessory

AC Adaptor, Cubase AI Download Information (MG10XU),

Owner’s Manual, Precautions, Technical Speciﬁcations (this leaﬂet)

Optional Accessory Mic Stand Adaptor: BMS-10A

Operating Temperature 0 to +40°C

*1 Noise is measured with A-weighting filter. *2 Crosstalk is measured with 1 kHz band pass filter.

Analog Input Characteristics

Input Jacks

PAD

26 dB

GAIN

Trim

Position

Actual

Load

Impedance

For Use

With

Nominal

Input level

Connector

Sensitivity *1 Nominal

Max. before

clip

MIC/LINE 1 – 4

OFF

+64 dB

3 kΩ

50-600 Ω

Mics/Lines

-72 dBu

(0.195 mV)

-60 dBu

(0.775 mV)

-40 dBu

(7.75 mV)

Combo jack*2

(Balanced)

+20 dB

-28 dBu

(30.9 mV)

-16 dBu

(122.8 mV)

+4 dBu

(1.228 mV)

+38 dB

-46 dBu

(3.884 mV)

-34 dBu

(15.46 mV)

-14 dBu

(154.6 mV)

-6 dB

-2 dBu

(615.6 mV)

+10 dBu

(2.451 V)

+30 dBu

(24.51 V)

LINE 5/6, 7/8

- - 10 kΩ 600 Ω Lines

-22 dBu

(61.56 mV)

-10 dBu

(245.1 mV)

+10 dBu

(2.451 V)

Phone jack *3

RCA Pin

(Unbalanced)

LINE 9/10

Phone jack *3

(Unbalanced)

0 dBu is referenced to 0.775 Vrms.

*1 Sensitivity is the lowest level that will produce an output of +4dBu (1.228V) or the nominal output level when the unit is set to maximum gain (all level knobs are

maximum position).

*2 1&Sleeve = Ground, 2&Tip = Hot, 3&Ring = Cold

*3 Tip = Signal, Sleeve = Ground

Analog Output Characteristics

Output Terminals

Actual Source

Impedance

For Use With

Nominal

Output level

Connector

Nominal Max. before clip

STEREO OUT [L, R] 75 Ω 600 Ω Lines

+4 dBu

(1.228 V)

+24 dBu

(12.28 V)

XLR-3-32 *1

Phone jack *2

(Balanced)

MONITOR OUT [L, R]

AUX (FX) SEND

150 Ω 10 kΩ Lines

+4 dBu

(1.228 V)

+20 dBu

(7.750 V)

Phone jack *2

(Impedance Balanced)

PHONES 110 Ω 40 Ω Lines 3 mW + 3 mW 100 mW + 100 mW Stereo phone jack

0 dBu is referenced to 0.775 Vrms.

*1 1 = Ground, 2 = Hot, 3 = Cold

*2 Tip = Hot, Ring = Cold, Sleeve = Ground

Digital Input / Output Characteristics

Output Terminals Format Data Length*1 Fs Connector

USB USB Audio Class 2.0 16 /24 bit

44.1 kHz, 48 kHz, 88.2 kHz,

96 kHz, 176.4 kHz, 192 kHz

USB Standard-B

*1 Data length depends on the particular audio format being used. USB Audio Class2.0: 16 / 24-bit, Yamaha Steinberg USB Driver: 24-bit

European Models

Inrush Current based on EN 55103-1:2009

1 A (on initial switch-on)

1 A (after a supply interruption of 5s)

Conforms to Environments: E1, E2, E3 and E4

* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the

manual file.

ZT57280

MIXING CONSOLE

Technical Specifications

See reverse side for block/level diagrams and dimensions.