Yamaha DSP-E200 Návod k obsluze
- Kategorie
- Audio zesilovače
- Typ
- Návod k obsluze
Natural Sound Digital Sound Field Processor
4 Programs for Digital Sound Field Processing
2 Programs for Dolby Surround (DOLBY PRO LOGIC and ENHANCED)
Center and Rear Channel Power Amplifier
25W (8Ω) RMS Output Power, 0.08% THD, 20-20,000 Hz (Center)
25W
+
25W (8Ω) RMS Output Power, 0.3% THD, 1,000 Hz (Rear)
Automatic Input Balance Control for Dolby Surround
Test Tone Generator for Easier Speaker Output Balance Adjustment
3 Center Channel Modes
Remote Control Capabilit
y
OWNER’S MANUAL
Thank you for selecting this YAMAHA digital sound field processor.
CONTENTS
Safety Instructions....................................2
Warning ...................................................3
Supplied Accessories ..............................3
Profile of This Unit ...................................4
Speaker Configurations for This Unit ......5
Connections ............................................ 6
Identification of Controls.........................10
Adjustment Before Operation.................11
Using Digital Sound Field Processor
(DSP)......................................................13
Notes about the Remote Control
Transmitter .............................................17
Specifications .........................................17
Troubleshooting......................................18
IMPORTANT!
Please record the serial number of this
unit in the space below.
Model:
Serial No.:
The serial number is located on the rear
of the unit.
Retain this Owner’s Manual in a safe
place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK), NO USER-SERVICEABLE
PARTS INSIDE, REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
•
Explanation of Graphical Symbols
CAUTION
DSP-E200
1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of
assurance that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
FCC INFORMATION
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
6A A unit and cart combination should
be moved with care.
Quick stops, excessive force,
and uneven surfaces may cause
the unit and cart combination to
overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block the
ventilation openings; or placed in a built-in installation,
such as a bookcase or cabinet that may impede the flow
of air through the ventilation openings.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances that
produce heat.
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced
by qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the unit;
or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or exhibits a
marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be taken
so that the grounding or polarization is not defeated.
2
SAFETY INSTRUCTIONS
3
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT
1 To ensure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install your unit in a cool, dry, clean place – away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers,
motors). To prevent fire or electrical shock, do not expose
to rain and water.
3 Do not operate the unit upside-down. It may overheat,
possibly causing damage.
4 Never open the cabinet. If a foreign object drops into the
set, contact your dealer.
5 Do not place records or other objects on top of the unit;
this will block the ventilation holes, cause the internal
temperature to rise and may result in a failure.
6 Do not use force on switches, knobs or cords. When
moving the set, first turn the unit off. Then gently
disconnect the power plug and the cords connecting to
other equipment. Never pull the cord itself.
7 Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that your unit is faulty.
9 Do not connect audio equipment to the AC outlets on the
rear panel if that equipment requires more power than the
outlets are rated to provide.
SUPPLIED ACCESSORIES
After unpacking, check that the following parts are contained.
Remote Control Transmitter
Batteries (size AA, LR6, AM-3)
Audio Connection Cord x 2
YAMAHA and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the
sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA
and the Electronic Industries Association’s
Consumer Electronics Group recommend you to
avoid prolonged exposure from excessive
volume levels.
We Want You Listening For A Lifetime
4
PROFILE OF THIS UNIT
You are the proud owner of Yamaha DSP-E200 –an extremely sophisticated audio component. The Digital Sound Field Processor
(DSP) built in this unit takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a
whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and this unit
will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on. In addition,
you get incredible realism from Dolby-encoded video sources using the built-in Dolby Pro Logic Surround Decoder.
Rather than tell you about the wonders of digital sound field processing, however, let’s get right down to the business of setting up
the system and trying out its many capabilities. Please read this operation manual carefully and store it in a safe place for later
reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
What’s more, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of actual concert hall, theater, etc. to
allow you to accurately recreate one of several actual live
performance environments, all in your own home.
Dolby Pro Logic Surround
The Dolby Pro Logic Surround Decoder program lets you
experience the dramatic realism and impact of Dolby Surround
movie theater sound in your own home. Dolby Pro Logic gets
its name from its professional-grade steering logic circuitry,
which provides greater effective channel separation for a much
higher degree of realism than the “passive” Dolby Surround
circuits found in today’s typical home audio/video equipment.
Dolby Pro Logic Surround provides a true center channel, so
that there are four independent channels, unlike passive Dolby
Surround which has in effect only three channels: left, right,
and rear. This center channel allows listeners seated in even
less-than-ideal positions to hear the dialog originating from
action on the screen while getting a stereo effect as well.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system increases sound
stability at each channel and minimizes crosstalk between
channels, compared to conventional analog Dolby signal
processing.
In addition, this unit features a built-in automatic input balance
control. This circuit always presents you the best surround
conditions without performing manual adjustments.
“ENHANCED” Dolby Pro Logic Surround
This unit has a second mode of Dolby Pro Logic Surround
processing called “Enhanced Dolby Pro Logic Surround”
processing. Enhanced Dolby Pro Logic Surround processing
recreates the surround effect of a movie theater, effectively
duplicating their multiple surround loudspeaker system,
completely surrounding the listener with the sounds of the
action taking place on the screen.
5
SPEAKER CONFIGURATIONS FOR THIS UNIT
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with 5 speaker configuration. The speakers to be used with this unit will
be mainly front speakers, rear speakers, and a center speaker. (You can delete a center speaker. Refer to the “4-Speaker
Configuration” shown below.)
The front speakers are used for the output of the main source sound and the effect sound. They will probably be your present
stereo speaker system. The rear speakers are used for the output of the effect sound. And the center speaker is used for the
output of the center sound (dialogue etc.) encoded with the Dolby Surround. The rear and center speakers do not need to be equal
with the front speakers. However, all the speakers should have high enough power handling to accept the maximum output of this
unit that will drive them.
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and recommended. In
this configuration, the center speaker is necessary as well as
the rear speakers. If the digital sound field program is in the
DOLBY PRO LOGIC or ENHANCED, conversations will be
output from the center speaker and the ambience will be
excellent.
*
Set the center mode to the “NORMAL” or “WIDE” position.
(For details, refer to the page 11.)
4-Speaker Configuration
The center speaker is not used in this configuration. If the
digital sound field program is in the DOLBY PRO LOGIC or
ENHANCED, the center sound is output from the left and the
right front speakers. However, the sound effect of other
programs can be the same as that of the 5-speaker
configuration.
*
Be sure to set the center mode to the “PHANTOM” position.
(For details, refer to the page 11.)
SPEAKER PLACEMENT
The recommanded speaker configuration, the 5-speaker configuration, will require two speaker pairs: front speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Front: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet up from the floor.
Center: Precisely between the front speakers. (To avoid
interference to TV sets, use a magnetically shielded
speaker. If, however, it is not effective, keep the
speaker away from TV sets.)
Front L Center Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Front L Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L Rear R
Front R
Center
Front L
TV set
Rear R
Rear L
•
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
•
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this
unit.
•
Choose one of the following three ways to connect this unit to your amplifier.
A Connecting to an Integrated Amplifier or Stereo Receiver with PRE OUT
and MAIN IN terminals
CONNECTIONS
6
INPUT
TAPE
PB
REC
OUT
TAPE
MAIN
OUT
CENTER
OUT
CENTER REAR
SPEAKERS
AC OUTLET
UNSWITCHED
120V 60Hz
200W MAX.
1.6A MAX.
MAIN IN
PRE OUT
Front speakers
Right
Left
Integrated amp.
(U.S.A model)
To
AC outlet
Center speaker
Right
Left
Rear speakers
B Connecting to an Integrated Amplifier or Stereo Receiver that does not
have PRE OUT and MAIN IN terminals
If your amplifier or receiver has the REC OUT selector which is independent of the input selector, connect this unit to the amplifier
or receiver tape REC OUT and auxiliary (AUX) input terminals. If not, connect this unit to the amplifier or receiver tape REC OUT
and TAPE PB terminals.
If your system includes a tape deck which have been displaced by connecting this unit to the tape REC OUT terminals, reconnect
your tape deck to this unit’s TAPE PB and TAPE REC OUT terminals.
7
INPUT
TAPE
PB
REC
OUT
TAPE
MAIN
OUT
CENTER
OUT
CENTER REAR
SPEAKERS
AC OUTLET
UNSWITCHED
120V 60Hz
200W MAX.
1.6A MAX.
AUX
(TAPE PB)
REC OUT
LINE OUT
LINE IN
Front speakers
Left Right
Integrated amp.
Tape deck
(U.S.A model)
To
AC outlet
Center speaker
Right
Rear speakers
Left
C Connecting to a Control Amplifier and Power Amplifier
8
INPUT
TAPE
PB
REC
OUT
TAPE
MAIN
OUT
CENTER
OUT
CENTER REAR
SPEAKERS
AC OUTLET
UNSWITCHED
120V 60Hz
200W MAX.
1.6A MAX.
INPUT
PRE OUT
Front speakers
Left
Right
Power amp.
Control amp.
(U.S.A. model)
Center speaker
Right
Rear speakers
Left
To
AC outlet
9
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut to be as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
*
Use speakers with the specified impedance shown on the
rear of this unit.
How to Connect:
Red: positive (+)
Black: negative (–)
➀Press and hold the tab.
➁Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂Release the tab and
secure the wire.
CONNECTING SPEAKERS
ABOUT THE ACCESSORY TERMINALS
AC OUTLET (UNSWITCHED)
This unswitched AC outlet can be used for connection of the
power cord from another audio component. Note that the
power to that component is not affected by the ON or OFF
setting of the POWER switch of this unit.
Note: The maximum power (total power consumption of
components) that can be connected here is 200 watts.
CENTER OUT terminal
This terminal is for center-channel line output. There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect input terminal of the external amplifier to this
terminal.
If you use the built-in amplifier and the external power amplifier
at the same time, the sound will be output through both
speakers.
10
IDENTIFICATION OF CONTROLS
1POWER
Turns the power on/off.
2Display panel
Displays your selection on the DSP or
other informations.
3TAPE MONITOR
Used when you have connected the
tape deck to this unit’s TAPE terminals
to select that tape as the source. (See
page 14.)
4TEST
Used for speaker balance adjustment.
(See pages 11–12.)
5CENTER MODE
Selects center speaker mode. (See
page 11.)
6DIGITAL SOUND FIELD
PROCESSING programs
Selects a program from the digital
sound field processor. (See pages
13–15.)
7MASTER VOLUME
Turns the master volume level up/down.
8EFFECT ON/OFF
Switches on/off the digital sound field
processor. (See pages 13–15.)
9DELAY TIME
Adjusts delay time. (See page 15.)
0FRONT EFFECT LEVEL
Adjusts effect sound output level at
front speakers. (See page 16.)
ACENTER LEVEL
Adjusts center speaker sound output
level. (See page 16.)
BREAR LEVEL
Adjusts rear speaker sound output
level. (See page 16.)
CMUTING
When pressed, mutes the volume level.
To resume original volume level, press
this again.
While muting, the indicator on the
VOLUME control flashes on and off
continuously.
POWER
NATURAL SOUND DIGITAL SOUND FIELD PROCESSOR DSP–E200
TAPE
MONITOR
TEST
CENTER
MODE
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
ROCK
CONCERT
DOLBY SUR.
CONCERT
HALL
OFF
DIGITAL SOUND FIELD PROCESSING
VOLUME
–dB
ENHANCED VIDEO MOVIE CONCERT HALL
PRO LOGIC CONCERT MONO ROCK CONCERT
NORMAL
WIDE
PHANTOM
TEST
FC
R
DOLBY SURROUND
PRO • LOGIC
DELAY
ms
1
2
34 5
6
7
4 Select the center mode depending on your speaker
configuration.
(Refer to “SPEAKER CONFIGURATION” on page 5.)
On the feature of each mode, refer to the “Note” shown
below.
5
11
ADJUSTMENT BEFORE OPERATION
SPEAKER BALANCE ADJUSTMENT
Using the built-in test tone generator, this procedure lets you adjust the sound output level balance between the front, center, and
rear speakers. With this adjustment, the sound output level heard at the listening position will be the same from each speaker.
This is important for the best performance of digital sound field processor.
The adjustment of each speaker output level should be done at your listening position with the remote control transmitter.
Otherwise, the result may not be satisfactory.
1
Set to the “
∞
” position.
2
Set on the POWER of this unit and the amplifier etc.
3
Note
In step 4, when you select the center mode, note the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use the center speaker
smaller sized than the front speakers. In this mode,
the bass tone will be output from the front
speakers.
WIDE: Select this mode when you use the center speaker
approximately same sized as the front speakers.
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and the right front speakers.
2 3 1
54
— dB
VOLUME
0
POWER
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
ROCK
CONCERT
DOLBY SUR.
CONCERT
HALL
OFF
DIGITAL SOUND FIELD PROCESSING
NORMAL
WIDE
PHANTOM
CENTER
MODE
TEST
ENHANCED VIDEO MOVIE CONCERT HALL
PRO LOGIC CONCERT MONO ROCK CONCERTPRO LOGIC CONCERT MONO ROCK CONCERT
NORMAL
TEST
F C
R
DELAY
ms
Flashes on and off continuously.
6 Turn up the volume by using the remote control
transmitter. You will hear a test tone (like pink noise)
from the left front speaker, then the center speaker,
then the right front speaker, then the rear speakers, for
about two seconds each. The display illumination
changes as shown below.
*
The test tone from the left rear speaker and the right rear
speaker will be heard at the same time.
7 Make the sound output level of the center speaker the
same as that of the front speakers.
8 Make the sound output level of the rear speakers the
same as that of the front speakers.
12
9
Notes
●
Once you have completed these adjustments, use only this
unit’s VOLUME control to adjust listening volume. Do not
change any other volume settings in this unit.
●
If the connecting way of your components is B or C
shown on pages 7–8, also adjust the volume control(s) on
the integrated amplifier or power amplifier to achieve proper
balance.
●
In step 7, if the center mode is in the “PHANTOM”, the
sound output level of the center speaker can not be
adjusted. Because in this mode, the center sound is
automatically output from the left and right front speakers.
ENHANCED VIDEO MOVIE CONCERT HALLENHANCED VIDEO MOVIE CONCERT HALL
PRO LOGIC CONCERT MONO ROCK CONCERT
NORMAL
WIDE
PHANTOM
TEST
F C
R
DELAY
ms
CENTER LEVEL
+
_
ENHANCED VIDEO MOVIE CONCERT HALL
PRO LOGIC CONCERT MONO ROCK CONCERT
NORMAL
TEST
F C
R
DELAY
ms
Illuminates.
Adjustable.
Front (L)
Center
Rear
(L and R)
Front (R)
REAR LEVEL
+
_
ENHANCED VIDEO MOVIE CONCERT HALLENHANCED VIDEO MOVIE CONCERT HALL
PRO LOGIC CONCERT MONO ROCK CONCERTPRO LOGIC CONCERT MONO ROCK CONCERT
NORMAL
WIDE
PHANTOM
TEST
F C
R
DELAY
ms
TEST
ENHANCED VIDEO MOVIE CONCERT HALLENHANCED VIDEO MOVIE CONCERT HALL
PRO LOGIC CONCERT MONO ROCK CONCERTPRO LOGIC CONCERT MONO ROCK CONCERT
NORMAL
WIDE
PHANTOM
TEST
F C
R
DELAY
ms
Stop flashing and disappears.
Illuminates.
Adjustable.
13
Description of Dolby Pro logic Surround
DOLBY PRO LOGIC SURROUND: This unit employs
the Dolby Pro Logic Surround system. This system is similar to
professional Dolby Stereo decoders used in movie theaters.
The Dolby Pro Logic Surround system, by employing a four-
channel system, divides the input signals into four levels: the
left and right main channels, the center channel (to characterize
dialogue), and the rear surround-sound channels (to
characterize sound effects, background noise and other ambient
noise).
Dolby Surround is encoded on the sound track of commercially
available video cassettes and video discs as well. When you
play a source encoded with Dolby Surround on your home video
system, the Dolby Pro Logic Surround mode on this unit
decodes the signal and feeds the surround-sound effects.
The Dolby Pro Logic Surround mode may not be always
effective on video sources not encoded with Dolby Surround.
Manufactured under license from Dolby Laboratories Licensing
Corporation. Additionally licensed under one or more of the
following patents: U.S. numbers 3,632,886, 3,746,792, and
3,959,590; canadian numbers 1,004,603 and 1,037,877.
“Dolby” and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
DESCRIPTION OF EACH SOUND FIELD PROGRAM
PROGRAM
FEATURE
This program is effective on the play of the sources encoded with the Dolby Surround.
PRO LOGIC
The employment of the digital signal processing system improves crosstalk and transfers the sound
source more smoothly and precisely,comparing with the conventional type. A stable movie sound field is recreated.
This program is effective on the play of the sources encoded with the Dolby Surround.
ENHANCED
Enhancing the “Normal” Dolby Pro Logic, the DSP technology simulates the multi-surround speaker
systems of the 35 mm film theater, so widening the surrounded-sound field with greater presence.
CONCERT VIDEO
This program is effective on music videos and excellent in depth and clarity for vocals. For opera, the
orchestra and stage are ideally recreated, so letting you feel as if you were in an actual concert hall.
MONO MOVIE
This program is designed specifically to enhance mono source programs. Compared to a strictly mono
setting, the sound image created in this mode is wider and slightly forward of the speaker pair, lending an
immediacy to the overall sound. It is particularly effective when used with old mono movies, news
broadcasts and dialogue.
ROCK CONCERT This program will suit to rock music. A big, powerful sound is reproduced lively and dynamically.
CONCERT HALL
In this program, the center seems even more deeply behind the front speaker pair, creating an expansive,
large hall ambience.
OFF switch: When any program is not used with the selected source, press this switch. The sound is output only from the
front speakers.
USING DIGITAL SOUND FIELD PROCESSOR (DSP)
This unit incorporates a sophisticated, multi-program digital sound field processor, which allows you to expand and shape the audio
sound field from both the audio and video sources, for a theater-like experience in the listening/viewing room.
This digital sound field processor has 6 programs; 4 programs for digital sound field processing and 2 programs for the Dolby Pro
Logic Surround sound system (DOLBY PRO LOGIC and ENHANCED). You can create excellent audio sound field by selecting
the suitable program and adding desired adjustments. In addition, when the digital sound field program is in the DOLBY PRO
LOGIC or ENHANCED, the built-in automatic input balance control functions. This presents you the best surround condition
without adjusting it manually.
14
TO PLAY SOURCE WITH THE DIGITAL SOUND FIELD PROCESSOR
1
Set to the “
∞
” position.
2
3
Select a source using the input selector on the
integrated amplifier etc.
* To select a tape deck connected to this unit’s TAPE
terminals, set the TAPE MONITOR switch to on.
(Otherwise, set this switch to off.)
Note
If this unit is connected to the TAPE REC OUT terminals of
the integrated amplifier etc., the following operations should
be done.
• If your amplifier has the REC OUT selector which is
independent of the input selector;
1. Set the input selector to the AUX position.
2. Select the source to be input to this unit using the REC
OUT selector.
• If your amplifier does not have the REC OUT selector
which is independent of the input selector;
1. Set the TAPE monitor switch on the amplifier to on.
2. Select the source to be input to this unit using the input
selector.
4
Play the source.
5
Select a desired program suitable for the source.
The corresponding indicator will illuminate.
6
Adjust to the desired output level.
7 If desired, adjust the delay time and the output level of
each speaker. (For details, refer to the corresponding
descriptions on the next pages.)
5
3
2 1,6
— dB
VOLUME
0
POWER
TAPE
MONITOR
TEST
CENTER
MODE
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
ROCK
CONCERT
DOLBY SUR.
CONCERT
HALL
OFF
DIGITAL SOUND FIELD PROCESSING
PRO LOGIC
0
— dB
VOLUME
15
Adjustment of DELAY TIME
You can adjust the time difference between the beginning of
the source sound and the beginning of the effect sound with
the DELAY TIME keys.
The DELAY TIME keys are effective with all programs.
By applying more or less delay, sound effects, background
noise, and ambient noise coming at you from the rear speakers
can be enhanced or subdued for extra effect.
1 PRO LOGIC: from 15 to 30 milliseconds
(Preset value: 20 milliseconds)
2 ENHANCED: from 15 to 30 milliseconds
(Preset value: 20 milliseconds)
3 CONCERT VIDEO: from 1 to 100 milliseconds
(Preset value: 25 milliseconds)
4 MONO MOVIE: from 1 to 100 milliseconds
(Preset value: 25 milliseconds)
5 ROCK CONCERT: from 1 to 100 milliseconds
(Preset value: 15 milliseconds)
6 CONCERT HALL: from 1 to 100 milliseconds
(Preset value: 30 milliseconds)
By continuously pressing “+” or “–” of the DELAY TIME keys,
the value changes continuously.
However, the value stops changing momentarily at the preset
point.
Note
Adding too much delay will cause an unnatural effect with
some sources. Experiment with the DELAY TIME keys to
create an effect that you find most suitable.
To obtain the best performance of this unit:
If the connecting way of your components is A or C shown
on pages 6–8, set the volume control on the integrated
amplifier or control amplifier to about the halfway position
between the min. and max.
Notes
●
If you prefer to cancel the selected program, press the OFF
switch. The sound will be the normal 2-channel stereo
without surround sound effect.
●
In the CONCERT VIDEO, MONO MOVIE, ROCK
CONCERT and CONCERT HALL, no sound is heard from
the center speaker.
●
When the monaural sound source is played in the DOLBY
PRO LOGIC or ENHANCED, no sound is heard from the
front speakers and the rear speakers. Sound is heard only
from the center speaker. However, if the center mode is in
the PHANTOM, the front speakers output the sound of the
center speaker.
●
If the connected external amplifier has a built-in surround
sound or ambience circuitry, be sure that the surround or
ambience circuitry on that amplifier is off while you are using
this unit’s Dolby Pro Logic Surround decoding function.
●
When this unit is in the Dolby Pro Logic Surround mode, if
the main-source sound is considerably altered by
overadjustment of the BASS or TREBLE controls on the
integrated amplifier etc., the relationship with the center and
rear channels may produce an unnatural effect.
DELAY
TIME
ENHANCED VIDEO MOVIE CONCERT
PRO LOGIC CONCERT MONO ROCK C
O
N
PHP
H
TEST
F C
R
DELAY
ms
Adjustable.
16
Adjustment of the CENTER LEVEL
Adjustment of the REAR LEVEL
Adjustment of the FRONT EFFECT LEVEL
If desired, you can adjust the effect sound output level of the
front speakers with these keys. The output level is preset to be
80. However, you can adjust the level between 1 and 100.
●
If the digital sound field program is in the DOLBY PRO
LOGIC, the FRONT EFFECT LEVEL keys do not function.
●
Once the output level is adjusted, the level value will be
common among all the digital sound field programs except
the DOLBY PRO LOGIC .
●
If any digital sound field program is not used, the FRONT
EFFECT LEVEL keys do not function.
If desired, you can adjust the sound output level of the center
speaker with these keys even if the output level is already set
in “SPEAKER BALANCE ADJUSTMENT” on page 12.
●
By continuously pressing “+” or “–” of the CENTER LEVEL
keys, the level value changes continuously. However, the
value stops changing momentarily at the point which was
once set in the TEST mode.
●
If the digital sound field program is in the CONCERT
VIDEO, MONO MOVIE, ROCK CONCERT or CONCERT
HALL, the CENTER LEVEL keys can not function.
●
Once the output level is adjusted, the level value will be
common among the DOLBY PRO LOGIC and ENHANCED.
●
If any digital sound field program is not used, the CENTER
LEVEL keys do not function.
If desired, you can adjust the sound output level of the rear
speakers with these keys even if the output level is already set
in “SPEAKER BALANCE ADJUSTMENT” on page 12.
●
By continuously pressing “+” or “–” of the REAR LEVEL
keys, the level value changes continuously. However, the
value stops changing momentarily at the point which was
once set in the TEST mode.
●
Once the output level is adjusted, the level value will be
common among all the digital sound field programs.
●
If any digital sound field program is not used, the REAR
LEVEL keys do not function.
Note
The values of the DELAY TIME, the FRONT EFFECT LEVEL,
CENTER LEVEL, and REAR LEVEL you set the last time will
remain memorized even when the power of this unit is off.
However, if the power plug cord is disconnected for more than
two weeks, these values will revert to factory-preset levels.
DELAY
TIME
FRONT EFFECT LEVEL
ENHANCED VIDEO MOVIE CONCERTENHANCED VIDEO MOVIE CONCERT
PRO LOGIC CONCERT MONO ROCK PRO LOGIC CONCERT MONO ROCK
P
TEST
F C
R
DELAY
ms
DELAY
TIME
CENTER LEVEL
ENHANCED VIDEO MOVIE CONCERT
PRO LOGIC CONCERT MONO ROCK CO
N
PH
TEST
F C
R
DELAY
ms
DELAY
TIME
REAR LEVEL
ENHANCED VIDEO MOVIE CONCERT ENHANCED VIDEO MOVIE CONCERT
PRO LOGIC CONCERT MONO ROCK CPRO LOGIC CONCERT MONO ROCK C
N
PH
TEST
F C
R
DELAY
ms
Adjustable.
Illuminates.
Adjustable.
Illuminates.
Adjustable.
Illuminates.
17
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
●
Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote-control transmitter operation range
Notes
●
There should be no large obstacles between the remote
control transmitter and the main unit.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
SPECIFICATIONS
Minimum RMS Output Power per Channel
Center (8 ohms, 20 Hz – 20 kHz, 0.08% THD)
..........................................................................................25W
Rear L, R (8 ohms, 1 kHz, 0.3% THD) ...................25W+25W
Input Sensitivity/Impedance
INPUT.........................................................150 mV/47 k-ohms
Output Level/Impedance
MAIN OUT/CENTER OUT....................................1V/1 k-ohms
Frequency Response (20 Hz to 20 kHz)
INPUT to MAIN OUT..................................................0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
INPUT to MAIN OUT (1 V) .............................................0.01%
Signal-to-Noise Ratio (IHF-A Network)
MAIN OUT (Input Shorted)..............................................95 dB
Residual Noise (IHF-A Network)
MAIN OUT.........................................................................5 µV
Channel Separation
(Input 5.1 k-ohms Shorted 1 kHz/10 kHz)...............65 dB/50 dB
Power Supply
[U.S.A. and Canada models].......................AC 120 V, 60 Hz
[Australia and U.K. models].........................AC 240 V, 50 Hz
[Europe model]............................................AC 230 V, 50 Hz
[General model]..................AC 110/120/220/240V, 50/60 Hz
Power Consumption............................................................90W
AC Outlet
1 UNSWITCHED OUTLET...........................200W max. total
Dimensions (W x H x D).......................435 x 151.3 x 296.7 mm
(17-1/8” x 5-15/16” x 11-11/16”)
Weight......................................................7.7 kg (16 lbs. 15 oz.)
Accessories......................................Remote control transmitter
Batteries
Audio connection cord x 2
Specifications subject to change without notice.
2
3
1
30°
30°
Remote-control
sensor
Within approximately
7 m (23 feet)
18
SYMPTOM
The unit fails to turn on when the POWER
switch is pressed.
No sound.
The sound suddenly goes off.
Only one side speaker outputs the sound.
Sound “hums”.
No sound from the rear speakers.
No sound from the center speaker.
The remote control transmitter does not
work.
The distance or range within which the
remote control transmitter can be used
decreases.
The sound is degraded when monitoring
is performed by using the headphones
connected to the compact disc player or
cassette deck which are connected with
this unit.
CAUSE
Power cord is not plugged in or is not
completely inserted.
Incorrect output cord connections.
The MUTING switch is ON.
The protection circuit has activated because
of short circuit etc.
Incorrect cord connections.
Incorrect cord connections.
The rear effect sound output level is set to 0.
The monaural sound source is played in the
DOLBY PRO LOGIC or ENHANCED.
The center sound output level is set to 0.
The center mode is in the PHANTOM.
Incorrect sound field program selection.
No sound field program is selected.
Direct sunlight or lighting (of an inverter type
of flourescent lamp etc.) is striking the
remote control sensor of the main unit.
The batteries of this remote control
transmitter are too weak.
Power cord of this unit is not plugged.
REMEDY
Firmly plug in the power cord.
Connect the cords properly. If the problem
persists, the cords may be defective.
First, turn the volume control to the full left.
Then, turn the MUTING switch off with the
remote control transmitter and adjust the
volume.
Turning the unit off and then on will reset the
protection circuit.
Connect the cords properly. If the problem
persists, the cords may be defective.
Firmly connect the audio plugs. If the
problem persists, the cords may be
defective.
Turn up the sound output level with the
REAR LEVEL keys.
Select another program suitable for the
monaural sound source.
Turn up the sound output level with the
CENTER LEVEL keys.
Select the NORMAL or WIDE.
Select an appropriate program.
Change position of the main unit.
Replace the batteries with new ones.
Plug in the power cord.
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
TROUBLESHOOTING
YAMAHA ELECTRONICS CORPORATION, USA6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.SIEMENSSTR. 22-34, D-25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B.J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Yamaha DSP-E200 Návod k obsluze
- Kategorie
- Audio zesilovače
- Typ
- Návod k obsluze
v jiných jazycích
- polski: Yamaha DSP-E200 Instrukcja obsługi
- español: Yamaha DSP-E200 El manual del propietario
- italiano: Yamaha DSP-E200 Manuale del proprietario
- Deutsch: Yamaha DSP-E200 Bedienungsanleitung
- svenska: Yamaha DSP-E200 Bruksanvisning
- português: Yamaha DSP-E200 Manual do proprietário
- français: Yamaha DSP-E200 Le manuel du propriétaire
- Türkçe: Yamaha DSP-E200 El kitabı
- English: Yamaha DSP-E200 Owner's manual
- dansk: Yamaha DSP-E200 Brugervejledning
- русский: Yamaha DSP-E200 Инструкция по применению
- suomi: Yamaha DSP-E200 Omistajan opas
- Nederlands: Yamaha DSP-E200 de handleiding
- română: Yamaha DSP-E200 Manualul proprietarului
Související papíry
-
Yamaha DSP-100 Návod k obsluze
-
-
-
-
-
-
-
-
-