ENGLISH INSTALLATION AND USER'S MANUAL
ITALIANO MANUALE D'INSTALLAZIONE E D'USO
FRANÇAIS NOTICE D'INSTALLATION ET D'UTILISATION
ESPAÑOL MANUAL DE USO E INSTALACIÓN
DEUTSCH EINBAU- UND BEDIENUNGSANLEITUNG
NEDERLANDS HANDLEIDING VOOR INSTALLATIE EN GEBRUIK
ČESTÍNA NÁVOD K INSTALACI A POUŽITÍ
SLOVENČINA NÁVOD NA INŠTALÁCIU A POUŽITIE
INSTALLATION AND USER’S MANUAL
02
02
04
05
06
13
CONTENT
INTRODUCTION
SAFETY PRECAUTION
ELECTRICA L INSTALLATION
SPECIFICATION
INSTALLATION (VENT OUTSIDE)
INSTALLATION (VENT INSIDE)
DESCRIPTION OF COMPONENTS
OPERATION
MAINTENANCE
TROBULESHOOTING
CONFORMITY WITH DIRECTIVES
ENVIRONMENTAL PROTECTION
17
17
20
21
22
22
1
INTRODUCTION
Thank you for choosing this cooker hood.
This instruction manual is designed to provide you with all required
instructions related to the installation, use and maintenance of the appliance.
In order to operate the unit correctly and safety, please read this instruction
manual carefully before installation and usage.
The cooker hood uses high quality materials, and is made with a streamlined
design. Equipped with large power electric motor and centrifugal fan, it also
provides strong suction power, low noise operation, non-stick grease filter and
easy assembly installation.
Hereby, Candy Hoover Group Srl declares that the radio equipment is in
compliance with Directive 2014/53/EU and with the relevant Statutory
internet address: www.candy-group.com
SAFETY PRECAUTION
Never let the children operate the machine.
The cooker hood is for home use only, not suitable for barbecue, roast
shop and other commercial purpose.
The cooker hood and its filter should be clean regularly in order to
keep in good working condition.
Clean the cooker hood according to the instruction manual and keep
the unit from danger of burning.
Forbid the direct baking from the gas cooker.
Please keep the kitchen room a good convection.
Before connecting this appliance check that the power supply cord is
not damaged. A damage supply cord must be replaced by qualified
service personnel only.
There shall be adequate ventilation of the room when the range hood
is used at the same time as appliances burning gas or other fuels;
The air must not be discharged into a flue that is use d for exhausting
fumes from appliances burning gas or other fuels;
Regulations concerning the discharge of air have to be fulfilled.
Requirements (for the UKCA market).
The full text of the declaration of conformity is available at the following
2
Electrical Shock Hazard
˜
Only plug this unit into a properly earthed outlet. If in doubt seek
advice from a suitably qualified engineer.
˜
Failure to follow these instructions can result in death, fire, or
electrical shock.
5IFTFTIBMMCFBEFRVBUFWFOUJMBUJPOPGUIFSPPNXIFOUIFSBOHF
IPPEJTVTFEBUUIFTBNF UJNFBTBQQMJBODFTCVSOJOHHBTPSPUIFS
GVFMTOPUBQQMJDBCMFUPBQQMJBODFTUIBUPOMZEJTDIBSHFUIFBJSCBDL
JOUPUIFSPPN
UIFEFUBJMTDPODFSOJOHUIFNFUIPEBOEGSFRVFODZPGDMFBOJOH
UIFSFJTBGJSFSJTLJGDMFBOJOHJTOPUDBSSJFEPVUJOBDDPSEBODFXJUIUIF
JOTUSVDUJPOT
EPOPUGMBNFVOEFSUIFSBOHFIPPE
$"65*0/"DDFTTJCMFQBSUTNBZCFDPNFIPUXIFOVTFEXJUI
DPPLJOHBQQMJBODFT
- Children should be supervised to ensure that they do not play with
the appliance.
- Do not flambé under the range hood.
The range hood is not intended to be installed over a hob having
more than four hob elements
The lamp used in this product is not suitable for use
in the lighting of a room.
The purpose of this lamp is to provide illumination for using the product.
3
Direct Connection
The appliance must be connected directly to the mains using an
omnipolar circuit breaker with a minimum opening of 3mm between
the contacts.
The installer must ensure that the correct electrical connection has
been made and that it complies with the wiring diagram.
The cable must not be bent or compressed.
Regularly check the power plug and power cord for damage. If the
supply cord is damaged, it must be replaced by a special cord or
assembly available from the manufacturer or its service agent.
WARNING: This is a Class I appliance and MUST be earthed
This appliance is supplied with a 3 core mains cable coloured as
follows:
Brown = L or Live
Blue = N or Neutral
Green and Yellow = E or Earth
The fuse must be rated at 3 Amps.
Electrical Installation
All installation must be carried out by a competent person or qualified
electrician. Before connecting the mains supply ensure that the mains
voltage corresponds to the voltage on the rating plate.
4
Standard Installation Accessories List
Spec. Qty
Casing 1
Upper Chimney 1
Lower Chimney 1
Lower chimney bracket 1
Upper chimney bracket 1
Hanging Board 1
φ8 rawl plugs
φ8×φ6 white color 9
Screws
ST4.0×30 9
φ7.2screws
ST4.0×8 2
Illustration Picture
Air outlet 1
Carbon filter 2
Plasma 1
5
INSTALLATION
˄
˄
wall mounting
˅
If you have an outlet to the outside, your cooker hood can be connected as
below picture by means of an extraction duct (enamel, aluminum, flexible pipe
non flammabe with an interior diameter of 150mm)
1. Before installation, turn the unit off and unplug it from the outlet.
2. The cooker hood should be placed at a distance of 65~75cm above
the cooking plane for best effect.
3. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten
the bracket onto the wall with the screws provided.
Wall plug
Wall bracket 107.5mm
Screw(4mm x 30mm)
6
4. Leave up the cooker hood and hang onto the wall bracket hook.
5. Fix the one-way-valve to the air outlet of the cooker hood. Then,
attached the exhaust pipe onto the one-way-valve as shown below.
Exhaust pipe
Cooker hood
7
6. i. Place the glass in appropriate position on the top the cooker
hood.
ii. Fix with 4 screws and washer. In order to avoid the glass
cracking, please do not tighten the screws too strongly.
i. By Put the inner chimney into outer chimney .Then pulling out
the inner chimney upwards. Adjust to reach the height required.
ii. Sliding the chimney to adjust the chimney height. When the
height you required is reached, then hang the fixing hole to the fixing
screws as showed in below pictures.
Inner chimney
Outer chimney
8
8. i. Drill 2 x 8mm holes to accommodate the plate II. Screw and
tighten the plate II onto the wall with 2 screws provided.
ii. Assembly the chimney onto the unit and fix it with 2 screws.
Plate II
Wall plug
Screw
4mm x 8mm
Screw
(4mm x 30mm)
9
StandardInstallationAccessoriesList
Spec. IllustrationPicture Qty
AirDeflector 1
Bracket 1
ij8rawlplugs
ij8×ij6whitecolor
2
Screws
ST4.0×30
2
Screws
ST3.5×12
2
10
INSTALLATION(AIRDEFLECTOR):
Airdeflectorismentionedasincludedandnotoptional.
1. Beforeinstallation,curvebothendsofthebracketasshownbelow:
2. FixthebrackettotheT-shapedplasticoutletwith2pcsST3.5x12mm
screwsprovided.
3.Drill2holestoaccommodatethewallplugs,thenscrewandtightenthe
bracketontothewallwith2pcsST4x30mmscrewsprovided.
4.Attachtheexhaustpipeontotheairoutletofthecookerhoodasshownbelow:
5.Installthechimneytotheunitandfixit.
11
oi1MFBTFLJOEMZCFOPUFE5TIBQFEQMBTUJDPVUMFUBOEWGMBQTDBOOPU
CFVTFEBUUIFTBNFUJNF:PVDBOVTFUIFNJOUXPXBZT"EEW
GMBQPOFYJTUJOHPVUMFU6TF5TIBQFEQMBTUJDPVUMFUOPBEEW
GMBQw
oi/PUF5IFQSPEVDUJTQSPWJEFEXJUIWGMBQBDDFTTPSZ5IJT
BDDFTTPSZJTOPUNBOEBUPSZGPSJOTUBMMBUJPOPQFSBUJPOBOEVTFPG
UIFQSPEVDUw
12
INSTALLATION (VENT INSIDE)
If you do not have an outlet to the outside, exhaust pipe is not required and
the installation is similar to the one show in section “INSTALLATION (VENT
OUTSIDE)”.
Activated carbon filter can be used to trap odors.
In order to install the activated carbon filter, the grease filter should be
detached first. Press the lock and pull it downward.
Plug the activated carbon filter into the unit and turn it in clockwise direction.
Repeat the same on the other side.
NOTE:
oMake sure the filter is securely locked. Otherwise, it would loosen and
cause dangerous.
oWhen activated carbon filter attached, the suction power will be
lowere
13
Intended Use
Please read this user manual thoroughly before attempting to use this plasma filter
for the first time. This manual contains important information on safe installation, use
and care of this filter. Retain these instructions for future reference and pass on to the
next user.
This plasma filter can only be used safely if it is correctly installed according to the safety
instructions. The installer is responsible for ensuring that the appliance works correctly at its
installed location.
This plasma filter is intended for domestic use and household environment only. Do not use
the plasma filter for other uses than its specific purpose. Do not leave the appliance
unattended during operation.
This plasma filter is intended to remove airborne dust particles, pollen, micro-organisms
(house dust mites, bacteria, viruses and moulds), cigarette smoke and smells from the air.
Presence of smell will still be present when you are cooking and can only be completely
removed after you had finished your cooking. Harmful gases (carbon monoxide etc.) cannot
be removed.
The plasma filter produces ozone, the amount will depend on the time you use the filter.
When the plasma filter is placed in a well ventilated room, the amount emitted is within the
set safety limits and standard. A slight ionisation smell will be present during usage and do
not indicate a faulty connection or device
This appliance may be used by children over the age of 8 years old and by persons with
reduced physical, sensory or mental capacity or by persons with a lack of experience or
knowledge if they are supervised by someone who is responsible for their safety or have
been instructed in how to use the appliance safely and have understood the risks involved in
not using it properly.
Children must not play with the appliance. Cleaning and user maintenance must not be
performed by children unless they are over 15 years of age and are supervised. Keep
children below the age of 8 years old at a safe distance from the appliance and power cable.
Check the appliance for damage after unpacking it. Do not connect the appliance if it has
been damaged during transport.
Important
This plasma filter is intended for use in combination with an extractor hood
with metal grease filters
The manufacturer is not liable for any damage which is caused by
improper use or incorrect operation.
14
Operating Instructions
Warning: Only use the plasma filter in combination with an extractor unit with metal
grease filters. Always ensure that the plasma filter is in a location with good oxygen supply
and good permanent ventilation. Please refer to your extractor hood user manual.
Operating the Plasma Filter on the Extractor Hood
Touch the sensor buttons gently on the control panel on the extractor to operate this
appliance.
To achieve better air extraction, it is advisable to switch on the extractor hood a few minutes
before starting to cook and leave it on for approximately 15 minutes after cooking or at least
all cooking smell is completely removed.
The plasma filter uses a sensor switch that reacts to the air flow from the extractor hood.
When the extractor hood is switch ON, the air pass through a sensor to activate the plasma
filter automatically. It may take approximately 20 to 30 seconds to activate the plasma filter
depending on the type of extractor hood.
The indicator lamp on the plasma filter will light up and an audio signal will sound to indicate
that the plasma filter is now switch ON.
Cleaning the Plasma Filter
Little maintenance is needed as the plasma filter is cleaned automatically as soon as it is
put into operation. The electrodes exhibit a very long lifetime and are nearly
indestructible in destined operation.
The activated carbon filter is regenerated at each process, keeps its pores clean and is
expected to last for not less than 6 years if the activated carbon filter is use for not more
than 4 hours a day. Usage of more than 4 hours a day will reduce the lifespan of the
activated carbon filter.
Note: It is important to follow the maintenance instructions of your extractor hood. The
grease filter must be clean regularly and/or replace at appropriate intervals to prevent
contamination.
Periodic Maintenance for Plasma Filter
To ensure that your plasma filter is in satisfactory working condition, contact your local After
Sales Center once every 5 years to do periodic inspection on the plasma filter.
15
Trouble Shooting
Problem
Solution
The Plasma Filter
Does Not Work
Check power plug is connected properly and
main power switch is turned on
Check the fuse box of the plasma filter to
ensure fuse is not blown
Check if other electrical appliance are working
The Indicator Lamp
on the Plasma Filter
Did Not Light Up
Please contact your local After Sales Center
16
Wi-Fi Connection
Long press WiFi icon and enter into connecting mode: the backlit of WiFi icon
keep flashing indicate the connection is under connecting, the backlit of WiFi
icon is light on indicate it is connected, same for standby mode; long press
WiFi icon again and the connection will be stopped;
DESCRIPTION OF COMPONENTS
OPERATION
Boost 1(speed 4)
Press speed b button 1, the backlit of speed B button is on, and the cooker
hood is working at boost mode ;
Boost 2(speed 5)
Press speed b button 2, the backlit of speed B+ button is on, and the
cooker hood is working at boost mode ;
Light
Short press for lighting on & off
Quick timer: Long press the light button hold for 3 seconds, fan speed
buttons will flashing & into 5minutes count down, after 5 minutes motor &
light will turn off automatic with three Buzzer sound.
Medium Speed button
Airflow speed is ideally for ventilation in standard cooking operation.
High Speed button
When high density of smoke or steam produced, press high-speed button
for high effective ventilation.
CONFIGURATION 1
Low Speed button
It’s used for Ventilation on the kitchen. It is suitable for simmering and
cooking which do not make much steam.
17
STANDBY MODE.
After plug in, all lighting, system in
STANDBY MODE
.
Medium Speed button
Airflow speed is ideally for ventilation in standard cooking operation.
High Speed button
When high density of smoke or steam produced, press high-speed button
for high effective ventilation.
Booster function
This hood has a booster function. To activate the booster, Press
to speed 4, enter into highest speed while the hood is in use and it will
increase speed for 5 minutes, before slowing down again.
Light
Short press for lighting on & off
Quick timer: Long press the light button hold for 3 seconds, fan speed
buttons will flashing & into 5minutes count down, after 5 minutes motor &
light will turn off automatic with three Buzzer sound.
CONFIGURATION 2
Wi-Fi Connection
Long press WiFi icon and enter into connecting mode: the backlit of WiFi
icon keep flashing indicate the connection is under
connecting, the
backlit of WiFi icon is light on indicate it is connected, same for standby
mode; long press WiFi icon again and the connection will be stopped;
Low Speed button
It’s used for Ventilation on the kitchen. It is suitable for simmering and
cooking which do not make much steam.
18
/