Yamaha UX96 Uživatelský manuál

Značka: Yamaha

Modelka: UX96

Kategorie: Hudební vybavení

Typ: Uživatelský manuál

USB-MIDI INTERFACE

Owner's Manual

Bedienungsanleitung

Mode d'emploi

EnglishDeutschFrançais

SPECIAL MESSAGE SECTION

This product utilizes an external power supply

(adapter). DO NOT connect this product to any

power supply or adapter other than one

described in the manual, on the name plate, or

specifically recommended by Yamaha.

WARNING: Do not place this product in a

position where anyone could walk on, trip over,

or roll anything over power or connecting cords

of any kind. The use of an extension cord is not

recommended! If you must use an extension

cord, the minimum wire size for a 25' cord (or

less) is 18 AWG. NOTE: The smaller the AWG

number, the larger the current handling capacity.

For longer extension cords, consult a local

electrician.

This product should be used only with the

components supplied or; a cart, rack, or stand

that is recommended by Yamaha. If a cart, etc.,

is used, please observe all safety markings and

instructions that accompany the accessory

product.

SPECIFICATIONS SUBJECT TO

CHANGE:

The information contained in this manual is

believed to be correct at the time of printing.

However, Yamaha reserves the right to change

or modify any of the specifications without notice

or obligation to update existing units.

Do not attempt to service this product beyond

that described in the user-maintenance

instructions. All other servicing should be

referred to qualified service personnel.

This product, either alone or in combination with

an amplifier and headphones or speaker/s, may

be capable of producing sound levels that could

cause permanent hearing loss. DO NOT operate

for long periods of time at a high volume level or

at a level that is uncomfortable. If you experience

any hearing loss or ringing in the ears, you

should consult an audiologist. IMPORTANT: The

louder the sound, the shorter the time period

before damage occurs.

Some Yamaha products may have benches and/

or accessory mounting fixtures that are either

supplied with the product or as optional

accessories. Some of these items are designed

to be dealer assembled or installed. Please

make sure that benches are stable and any

optional fixtures (where applicable) are well

secured BEFORE using. Benches supplied by

Yamaha are designed for seating only. No other

uses are recommended.

NOTICE:

Service charges incurred due to a lack of

knowledge relating to how a function or effect

works (when the unit is operating as designed)

are not covered by the manufacturer's warranty,

and are therefore the owners responsibility.

Please study this manual carefully and consult

your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are

both user safe and environmentally friendly. We

sincerely believe that our products and the

production methods used to produce them, meet

these goals. In keeping with both the letter and

the spirit of the law, we want you to be aware of

the following:

Disposal Notice:

Should this product become damaged beyond

repair, or for some reason its useful life is

considered to be at an end, please observe all

local, state, and federal regulations that relate to

the disposal of products that contain lead,

batteries, plastics, etc. If your dealer is unable to

assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The graphic below indicates the location of the

name plate for this model. The model number,

serial number, power requirements, etc., are

located on this plate. You should record the

model number, serial number, and the date of

purchase in the spaces provided below and

retain this manual as a permanent record of your

purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

93-DC

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are

not limited to, the following:

• Do not open the instrument or attempt to disas-

semble the internal parts or modify them in any

way. The instrument contains no user-service-

able parts. If it should appear to be malfunction-

ing, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service person-

nel.

• Do not expose the instrument to rain, use it near

water or in damp or wet conditions, or place

containers on it containing liquids which might

spill into any openings.

• If the USB cable becomes frayed or damaged,

or if there is a sudden loss of sound during use

of the instrument, or if any unusual smells or

smoke should appear to be caused by it, imme-

diately disconnect the USB cable, and have the

instrument inspected by qualiﬁed Yamaha ser-

vice personnel.

• Before cleaning the instrument, always remove

the USB cable. Never insert or remove a USB

cable with wet hands.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the USB cable near heat sources

such as heaters or radiators, and do not exces-

sively bend or otherwise damage the cable,

place heavy objects on it, or place it in a position

where anyone could walk on, trip over, or roll

anything over it.

• Unplug the USB cable when not using the

instrument, or during electrical storms.

• Before connecting the instrument to other elec-

tronic components, turn off the power for all

components. Before turning the power on or off

for all components, set all volume levels to mini-

mum. Also, be sure to set the volumes of all

components at their minimum levels and gradu-

ally raise the volume controls while playing the

instrument to set the desired listening level.

• Do not expose the instrument to excessive dust

or vibrations, or extreme cold or heat (such as in

direct sunlight, near a heater, or in a car during

the day) to prevent the possibility of panel disﬁg-

uration or damage to the internal components.

• Do not use the instrument near other electrical

products such as televisions, radios, or speak-

ers, since this might cause interference which

can affect proper operation of the other prod-

ucts.

• Do not place the instrument in an unstable posi-

tion where it might accidentally fall over.

• Before moving the instrument, remove all con-

nected cables.

• When cleaning the instrument, use a soft, dry

cloth. Do not use paint thinners, solvents, clean-

ing ﬂuids, or chemical-impregnated wiping

cloths. Also, do not place vinyl, plastic or rubber

objects on the instrument, since this might dis-

color the panel or keyboard.

• Do not rest your weight on, or place heavy

objects on the instrument, and do not use

excessive force on the connectors.

Yamaha cannot be held responsible for dam-

age caused by improper use or modiﬁca-

tions to the instrument, or data that is lost or

destroyed.

(3)-6

Welcome to the UX96

Thank you for choosing the Yamaha UX96 USB-MIDI interface.

The UX96 is a MIDI interface that features fast data transfer via USB connection

and simultaneous playback of up to 96 channels. Connect the UX96 to a computer

that has a USB terminal and enjoy the advantages of digital music.

Please read this owner’s manual thoroughly to make the best use of the UX96.

After you read this manual, please keep it in a safe place for future reference.

Table of Contents

UX96 Features.................................................................................. 5

Package Contents............................................................................. 6

System Requirements ....................................................................... 7

Specifications ................................................................................... 7

Parts and Functions .......................................................................... 8

Connection ...................................................................................... 9

Installing the Driver ........................................................................ 10

Changing the driver setting (MIDI Patch Screen)............................ 20

Troubleshooting (FAQ)................................................................... 25

• The screen displays in this Owner’s Manual are intended for instructional pur-

poses, and may appear somewhat different from the screens that appear on

your computer.

• OMS

and are trademarks of Opcode Systems, Inc.

• The company names and product names in this Owner’s Manual are the trade-

marks or registered trademarks of their respective companies.

UX96 Features

● 96-channel Simultaneous Playback

You can use both MIDI IN/OUT terminals and the TO TG/INST terminal

(equivalent to a serial port on a computer) simultaneously. In this way, you can

build a powerful music production environment with 6 MIDI OUT ports (96

channels) and 2 MIDI IN ports (32 channels).

● Easy Hot Swap Connection

With a USB connection, you can connect and disconnect the USB cable while the

power to the computer is on. The UX96 operates on USB bus power and does not

require a power adaptor.

● USB Fast Data Transfer

USB connection enables a very quick response during multiport simultaneous

performance.

● Supports Windows and Macintosh

The UX96 supports Windows 98/Me/2000 and Mac OS 8.5 or higher (including

OS 9.1).

Notes on USB

Never connect or disconnect a USB cable under any of the following conditions.

Otherwise, the computer may lock up or UX96 functions may be disabled:

• The computer is checking the device or loading the driver.

• The computer is starting or quitting the OS.

• The computer is in or canceling Save Energy (Sleep) mode.

• A MIDI application program is running.

Also, do not perform any of the following operations. Otherwise, the computer

may lock up or the UX96 functions may be disabled:

• Do not frequently connect or disconnect the cables.

• Do not place the computer in or cancel Save Energy (Sleep) mode during MIDI

data transfer.

• Do not connect or disconnect cables, restart the computer, or install the driver

while a large amount of data is being transferred.

If you are using Windows 2000, Save Energy mode may be disabled depending on

your environment (USB Host Controller etc.) Even in this case, if you disconnect and

connect the USB cable, UX96 functions will be enabled again.

NOTE

Package Contents

The UX96 package contains the following items. Check the contents for missing

items.

• USB-MIDI interface (UX96 main unit)

• CD-ROM (Windows/Macintosh hybrid CD)

• USB cable

• Owner’s manual (this book)

About the included software

The included CD-ROM contains the following software (driver).

[Windows]

• USB-MIDI driver (YAMAHA USB-MIDI Driver)

You need this driver to operate the UX96. See page 11 for information on

installing the driver.

[Macintosh]

• OMS

This is a MIDI driver for Macintosh provided by Opcode Systems.

See page 15 and the included “OMS_2.3_Mac.pdf” OMS manual for

information on installing and using the driver.

• USB-MIDI driver (YAMAHA USB-MIDI Driver)

You need this driver to operate the UX96.

Be sure to install the OMS driver first, then install this driver. See page 15 for

information on installing the driver.

System Requirements

[Windows]

OS: Windows98/Me/2000

Computer: USB-supported IBM-PC or compatible computer

CPU: Pentium 166MHz or higher

Memory: 32 MB or higher (64 MB or higher is recommended)

Hard Disk: 2 MB or more of free space

[Macintosh]

OS: MacOS 8.5 through OS 9.1

Computer: Macintosh computer with built-in USB port

With some iMac models, you need to install “iMac Update 1.1,” provided by Apple

Computer. This program improves the USB software. For more information, visit the

Apple Computer web site (www.apple.com).

Memory: 64 MB or higher (128 MB or higher is recommended)

Turn off virtual memory.

Hard Disk: 2 MB or more of free space

Other: OMS 2.3.6 or later (included in the CD-ROM in the

package)

Speciﬁcations

Terminals: MIDI IN terminal, MIDI OUT terminal, TO TG/INST

terminal, USB terminal

Power Supply: USB bus power supply

Dimensions: 77(W) × 77(D) × 33(H) [mm]

Weight: 80g

Option: 8-pin peripheral cable for Apple Macintosh

Specifications and descriptions in this Owner’s Manual are for information

purposes only. Yamaha Corp. reserves the right to change or modify products or

specifications at any time without prior notice. Since specifications, equipment or

options may not be the same in every locale, please check with your Yamaha

dealer.

NOTE

Parts and Functions

1 Power LED

This LED lights up when the USB

terminal is connected and the

power is being supplied to the

UX96.

2 Terminal LEDs

These LEDs light up when MIDI

signal passes through the

corresponding terminals.

3 TO TG/INST terminal

Connect this terminal to the TO

HOST terminal on the MIDI device.

Use an optional 8-pin system

peripheral cable for Apple

Macintosh for connection.

Set the HOST SELECT switch of

the connected MIDI device to

“PC-1” or “Mac,” regardless of

the computer you are using.

4 MIDI OUT terminal

This terminal transmits MIDI signals

to connected MIDI devices. Use an

optional MIDI cable for connection.

5 MIDI IN terminal

This terminal receives MIDI signals

from connected MIDI devices. Use

an optional MIDI cable for

connection.

6 USB terminal

Connect this terminal to a

computer or a USB hub using a

USB cable.

USB-MIDI INTERFACE

MIDI IN

MIDI OUT

TO TG/INST

NOTE

Connection

This chapter explains how to connect MIDI devices, such as a tone generator and

a MIDI keyboard, to the UX96.

1. Connecting a computer

Connect the USB terminal of a computer to the USB terminal of the UX96

using a USB cable. At this time, you do not have to turn off the power to the

computer.

2. Connecting the TO TG/INST terminal to a MIDI device

Connect the TO HOST terminal of a MIDI device to the TO TG/INST terminal

of the UX96 using an optional serial cable (8-pin Macintosh peripheral cable).

At this time, set the HOST SELECT switch of the MIDI device to “PC-1” or

“Mac,” regardless of the computer you are using.

When you are using the TO TG/INST terminal, you can use five MIDI OUT

ports and one MIDI IN port to control the connected MIDI device.

3. Connecting the MIDI terminals to a MIDI device

Use optional MIDI cables to connect the MIDI IN terminal of the MIDI device

to the MIDI OUT terminal of the UX96. Also, connect the MIDI OUT terminal

of the MIDI device to the MIDI IN terminal of the UX96. At this time, set the

HOST SELECT switch of the MIDI device to “MIDI.”

UX96

Computer

USB cable

See page 10 for information

on installing the driver.

UX96

MIDI device

Set the HOST SELECT

switch of the MIDI

device to “PC-1” or

“Mac.”

Serial cable

Installing the Driver

To operate the UX96, you need to install the driver on the computer correctly.

The USB-MIDI driver is software that transmits MIDI signals back and forth

between sequence software and the UX96 via a USB cable.

If you are using a Macintosh computer, you also need to install the OMS driver

(page 15) as well as the USB-MIDI driver.

Windows 98/Me users →See page 11.

Windows 2000 users →See page 13.

Macintosh users →See page 15.

UX96

MIDI cables

MIDI device

Set the HOST SELECT

switch of the MIDI

device to “MIDI.”

UX96

OMS

Macintosh

UX96

Windows

Sequence

software

Sequence

software

Driver

USB-MIDI INTERFACE

MIDI IN

MIDI OUT

TO TG/INST

USB-MIDI INTERFACE

MIDI IN

MIDI OUT

TO TG/INST

Computer

USB cable

Windows users:

● Installing the driver on a Windows98/Me system

1. Start the computer.

2. Insert the included CD-ROM into the CD-ROM drive.

3. Use the included USB cable to connect the USB terminal of the computer (or

the USB hub) to the USB terminal of the UX96.

The UX96 is powered on and the system automatically displays the “Add New

Hardware Wizard.”

For Windows Me users, check the radio button to the left of “Automatic search for a

better driver (Recommended)” and click [Next]. The system automatically starts

searching and installing the driver. Proceed to Step 8. If the system does not detect

the driver, select “Specify the location of the driver (Advanced)” and specify the CD-

ROM drive’s root directory (e.g., D:\) to install the driver.

4. Click [Next].

The system displays a screen that enables you to select the search method.

NOTE

Windows 98

Windows Me

5. Check the radio button to the left of “Search for the best driver for your device.

(Recommended).” Click [Next].

The system displays a screen that enables you to select a location in which to

install the driver.

6. Check the “CD-ROM drive” box and uncheck all other items. Click [Next].

The system may ask you to insert a Windows CD-ROM while it checks for the driver.

Specify the root folder of the CD-ROM drive (such as D:\) and continue the installation.

7. When the system detects the driver on the CD-ROM and is ready for installa-

tion, it displays the following screen.

Make sure that the “YAMAHA USB MIDI Driver” is listed, and click [Next]. The

system starts the installation.

NOTE

8. When the installation is complete, the following screen appears.

Click [Finish].

Some computers may take about ten seconds to show this screen after the installation

is complete.

The driver has been installed.

● Installing the driver on a Windows 2000 system

1. Start the computer and use the “Administrator” account to log into Windows

2000.

Signature veriﬁcation], and check the radio button on the left of “Ignore -

Install all ﬁles, regardless of ﬁle signature” and click [OK].

3. Insert the included CD-ROM into the CD-ROM drive.

4. Use the included USB cable to connect the USB terminal of the computer (or

the USB hub) to the USB terminal of the UX96.

The UX96 is powered on and the system automatically displays the “Found

New Hardware Wizard.” Click [Next].

5. Check the radio button to the left of “Search for a suitable driver for my device.

(Recommended).” Click [Next].

The system displays a screen that enables you to select a location in which to

install the driver.

6. Check the “CD-ROM drives” box and uncheck all other items. Click [Next].

The system may ask you to insert a Windows CD-ROM while it checks for the driver.

Specify the root folder of the CD-ROM drive (such as D:\) and continue the installation.

7. When the installation is complete, the system displays “Completing the Found

New Hardware Wizard.”

Click [Finish].

Some computers may take about ten seconds to show this screen after the installation

is complete.

NOTE

Windows 98

Windows Me

NOTE

8. Restart the computer.

The driver has been installed.

● Selecting the destination for the MIDI signal output

This section explains how to set up the UX96 for use with Windows Media Player

(included in Windows) or an equivalent program. For information on setting up

your sequence software, refer to the owner’s manual for the software.

1. Select [My Computer | Control Panel] and double-click to open “Sounds and

Multimedia (Multimedia).”

For Windows Me users, if you do not see “Sounds and Multimedia” in the “Control

Panel,” click “View all Control Panel options.”

2. Click the “Audio (MIDI)” tab.

3. Click “Preferred device” in “MIDI Music Playback” to view “YAMAHA USB OUT

xx-yy.” Select a driver according to the port number of the connected MIDI

device. For Windows Me users, check the “Use only preferred devices” check-

box.

The variable “xx” represents the device number (page 21) and “yy” represents the port

number (page 20). If only one UX96 is connected, the device number is “0.”

For Windows 98 users, select the driver while “Single instrument” is selected.

If “YAMAHA USB OUT xx-yy” is not displayed, the drive has not been installed

correctly. Delete the driver (page 26) and re-install the driver.

4. Click [OK].

Windows 98

Windows Me

NOTE

● Using two or more UX96s

Follow the steps below to connect two or more UX96s. You do not need to re-

install the driver.

1. Start the computer.

2. Use the included USB cable to connect the USB terminal of the computer (or

the USB hub) to the USB terminal of the UX96.

When you turn on the power to connected multiple UX96s, the device number is

assigned, starting with 0, to the units in the order in which you turn on the power. If

you turn on the power to all units simultaneously, the device number is assigned

based on the order of the port numbers of the USB hub. However, this order may

change depending on the hub.

Macintosh users:

First install OMS before you install the USB-MIDI driver. Also, after installing the

driver, you will need to set up OMS (page 17).

● Installing OMS

1. Start the computer.

2. Insert the included CD-ROM into the CD-ROM drive. The system displays the

CD-ROM icon on the desktop.

3. Double-click to open the CD-ROM icon and double-click the “Install OMS

2.3.6” icon in the “OMS 2.3.6” folder inside “OMS E.”

Follow the instructions on the screen to install OMS. For more information on

installing and using OMS, refer to the included “OMS_2.3_Mac.pdf” manual.

● Installing the USB-MIDI driver

1. Start the computer.

2. Insert the included CD-ROM into the CD-ROM drive. The system displays the

CD-ROM icon on the desktop.

NOTE

3. Double-click the CD-ROM icon and double-click the “Install USB Driver” icon to

display the following installation screen.

4. The “Install Location” box displays the destination of the installation. If you

wish to change the destination disk or folder, use the [Switch Disk] button and

the pop-up menu to specify the desired destination.

This box usually displays the start-up disk as the destination.

5. Click the [Install] button. The system displays the following message: “This

installation requires your computer to restart after installing this software. Click

Continue to automatically quit all other running applications.” Click [Con-

tinue].

To cancel the installation, click [Cancel].

6. The installation starts. If the driver has already been installed, you will receive

the following message. To return to step 3, press [Continue]. To complete the

installation, click [Quit].

NOTE

7. When the installation is complete, the system displays the following message:

“Installation was successful. You have installed software which requires you to

restart your computer.” Click [Restart]. The computer automatically restarts.

You can locate the installed files in the following locations:

• System Folder | Control Panels | YAMAHA USB MIDI Patch

• System Folder | Extensions | USB YAMAHA MIDI Driver

• System Folder | OMS Folder | YAMAHA USB MIDI OMS Driver

● Setting up OMS

1. Start the computer.

2. Use the included USB cable to connect the USB terminal of the computer (or

the USB hub) to the USB terminal of the UX96.

Make sure that the UX96 is powered on and the power LED lights up.

3. Open the “OMS Applications” folder in the “Opcode” folder installed on the

hard disk, and double-click the “OMS Setup” icon to start the setup program.

4. If the AppleTalk dialog appears, click [Turn It Off], then click [OK] in the subse-

quent dialog box.

5. The system displays the “Create a New Studio Setup” dialog box. If this dialog

box does not appear, select “New Studio Setup” from the “File” menu.

6. Click [OK]. The system displays the “OMS Driver Search” dialog box. Remove

the check from the “Modem” and “Printer” check boxes, and click [Search].

7. After the search operation is complete, make sure that “USB-MIDI 1” is listed in

the “OMS Driver Setup” dialog, then click [OK].

If the UX96 is not detected correctly, “USB-MIDI 1” does not appear. Check the cable

connection and repeat the procedure from the beginning.

If your iMac does not detect the UX96, “iMac Update 1.1” may not have been installed.

See page 7 for more information.

The system displays one “USB-MIDI x” message for each connected UX96.

8. Make sure that “USB-MIDI 1” and multiple Port numbers are listed in the “OMS

MIDI Device Setup” dialog. Check all Ports 1–6 check boxes.

Click [OK].

9. The system displays a dialog box that enables you to save the setup ﬁle. Enter

the ﬁle name and click [Save].

NOTE

10. After you save the ﬁle, the system displays the following window.

The setting is complete if a “” mark appears before the file name.

You can also improve the setup view by changing the name and icon for each

port. For more information, refer to the included “OMS_2.3_Mac.pdf.”

The driver installation and OMS setup is now complete.

● Using two or more UX96s

First connect multiple UX96s, then proceed to the OMS setup procedure

(page 17).

Changing the driver setting (MIDI

Patch Screen)

You can change the assignment of I/O ports on the UX96 and port numbers

selected from your computer.

Sequence software transmits and receives MIDI signals to and from the UX96 via

the driver (page 10). The UX96 features MIDI IN/OUT terminals and a TO TG/

INST terminal. Select the I/O ports on the UX96 from your computer (sequence

software). You specify the I/O ports of the UX96 using the computer’s sequence

software. Changing the driver setting enables you to change I/O assignments

without re-patching cables.

For example, you can transmit an identical MIDI signal to multiple ports, or

transmit layered MIDI signals from multiple ports to a single port. Also, you can

directly route MIDI signals from MIDI IN to MIDI OUT.

The following table shows the assignment of the port numbers and I/O ports.

With the default settings, the port number matches the computer’s port number.

If a tone generator connected to the TO TG/INST terminal does not support multiport

specifications, the selection of ports B–E will be ignored.

port number MIDI output port MIDI input port

Port 1 MIDI OUT MIDI IN

Port 2 TO TG/INST -A TO TG/INST

Port 3 TO TG/INST -B —

Port 4 TO TG/INST -C —

Port 5 TO TG/INST -D —

Port 6 TO TG/INST -E —

NOTE

Stránka se načítá ...

Yamaha UX96 Uživatelský manuál

Značka: Yamaha

Modelka: UX96

Kategorie: Hudební vybavení

Typ: Uživatelský manuál

Stáhnout PDF

zpráva

v jiných jazycích

polski: Yamaha UX96 Instrukcja obsługi
español: Yamaha UX96 Manual de usuario
italiano: Yamaha UX96 Manuale utente
Deutsch: Yamaha UX96 Benutzerhandbuch
svenska: Yamaha UX96 Användarmanual
português: Yamaha UX96 Manual do usuário
français: Yamaha UX96 Manuel utilisateur
Türkçe: Yamaha UX96 Kullanım kılavuzu
English: Yamaha UX96 User manual
dansk: Yamaha UX96 Brugermanual
русский: Yamaha UX96 Руководство пользователя
suomi: Yamaha UX96 Ohjekirja
Nederlands: Yamaha UX96 Handleiding
română: Yamaha UX96 Manual de utilizare

Yamaha UX96 Uživatelský manuál

Yamaha UX96 Uživatelský manuál

v jiných jazycích

Související papíry