Briggs & Stratton 881634 Uživatelský manuál

Walk Behind Lawn Mower

Model Description

Walk Behind Lawn Mower: 19’’ / 48 cm

Walk Behind Lawn Mower: 21” / 53 cm

Walk Behind Lawn Mower: 19” / 48 cm

Walk Behind Lawn Mower: 21” / 53 cm

Walk Behind Lawn Mower: 19” / 48 cm

Walk Behind Lawn Mower: 21” / 53 cm

Original Instruction

1752053

Revision: C

en

Operator’s Manual

Betjeningsvejledning

Bedienungsanleitung

Manual del Operario

Návod k obsluze

Manuel de l’opérateur

Manuale dell’Operatore

Gebruiksaanwijzing

Bruksanvisning

da

de

es

cs

fr

it

nl

sv

Not for

Reproduction

2

www.BRIGGSandSTRATTON.com

GENERAL INFORMATION

THANK YOU for purchasing this quality-built lawn mower. We’re pleased that you’ve placed your confidence in our brand.

When operated and maintained according to the instructions in this manual, your lawn mower will provide many years of

dependable service.

SAFETY AND INTENDED USE

This manual contains safety information to make you aware of the hazards and risks associated with lawn mowers and how

to avoid them. This lawn mower is designed and intended only for finish cutting of established lawns and is not intended for

any other purpose. It is important that you read and understand these instructions thoroughly before attempting to start or

operate this equipment. Save these original instructions for future reference.

FINAL ASSEMBLY

Some units may require final assembly before use. See Assembly section of this manual for instructions on final assembly

procedures. Follow the instructions completely.

PRODUCT SUPPORT

You never have to look far for quality support and service for your lawn mower. Use our dealer locator at www.

BRIGGSandSTRATTON.COM to find the authorized service center nearest you, or contact the retailer from whom the unit

was purchased. To obtain an Illustrated Parts List for your product, please visit our web-site.

Product Identification Tag

Part No. xxxxxxx

xxxxxxxxxxxxxxx

Serial No. xxxxxxxxxx

20xx

kW: x.xx

xxxx max

xxxxxxxxxxxxxxxxxxxxxxx

xxx dB

kg: xxx

A

B

C

D

E

F G

H

I

A. Manufacturer’s Identification Number

B. Manufacturer’s Serial Number

C. Power Rating in Kilowatts

D. Maximum Engine Speed in Rotations per Minute

E. Manufacturer’s Name and Address

F. Year of Manufacture

G. CE Compliance Logo

H. Mass of Unit in Kilograms

I. Guaranteed Sound Power in Decibels

Enter below the lawn mower model and serial numbers,

which can be found on the label attached to the rear of the

lawn mower housing. Also record the date of purchase

and attach your receipt as proof of purchase in the event

that warranty-related service work is required. Please have

these numbers handy when contacting us for replacement

parts or technical assistance.

PRODUCT REFERENCE DATA

Model Description Name/Number

Unit SERIAL Number

Dealer Name Date Purchased

ENGINE Reference Data

Engine Make Engine Model

Engine Type/Spec

Engine Code/Serial

Number

The Illustrated Parts List for this machine can be obtained from your authorized dealer. please provide model and serial

number when ordering replacement parts.

Not for

Reproduction

3

en

TABLE OF CONTENTS

Operator Safety ............................................................................. 4

Safety Alert Symbols and Signal Words .................................... 4

Hazard and Control Symbols ..................................................... 4

Owner’s Information .................................................................. 5

Responsibility of the Owner ....................................................... 5

Assembly ....................................................................................... 7

Description ................................................................................ 7

Intended Use/Limits of Use ....................................................... 7

Remove Lawn Mower from Carton ............................................ 7

Assemble the Handle ................................................................ 7

Assemble the Grass Catcher ..................................................... 8

Features and Controls .................................................................. 9

Lawn Mower Controls ................................................................ 9

Operation ....................................................................................... 10

Oil Recommendations ............................................................... 10

How to Check/Add Oil ............................................................... 10

Fuel Recommendations ............................................................ 10

How to Add Fuel ........................................................................ 10

How to Start the Lawn Mower .................................................... 11

How to Stop the Lawn Mower .................................................... 11

How to Adjust the Engine Speed ............................................... 11

How to Operate the Drive System ............................................. 11

How to Adjust the Handle .......................................................... 12

How to Adjust the Cutting Height ............................................... 12

How to Install and Remove the Grass Catcher .......................... 12

How to Install and Remove the Mulching plug (if equipped) ...... 13

For Best Mowing Results ........................................................... 13

Maintenance ................................................................................. 14

Maintenance Schedule .............................................................. 14

How to Clean and Inspect the Grass Catcher ........................... 14

How to Clean the Lawn Mower Housing and Drive System ....... 14

How to Inspect the Drive System ............................................... 14

How to Service the Cutting Blade .............................................. 15

How to Prepare the Lawn Mower for Storage ............................ 15

Troubleshooting ............................................................................ 16

Warranty ......................................................................................... 17

Specifications ................................................................................ 18

NOTE: In these instructions, “left” and “right” are referenced from the

operating position.

Table of Contents

Not for

Reproduction

4

www.BRIGGSandSTRATTON.com

Frostbite

Thrown objects

Keep bystanders away from machine

Sharp blades

Keep hands and feet away from

discharge area

Disconnect spark plug wire

Do not mow up and down slopes

Mow across face of slopes

Stop engine before leaving the machine

Look down and behind when moving

backwards

Oil

Fuel

Fuel Shutoff

Choke

On Off

Stop

Slow

Fast

Operator Safety

SAFETY ALERT SYMBOL AND SIGNAL

WORDS

The safety alert symbol and signal word (DANGER,

WARNING, CAUTION, or NOTICE) is used to indicate

the likelihood and potential severity of personal injury

and/or damage to the product. In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE indicates a situation that could result in

damage to the product.

HAZARD AND CONTROL SYMBOLS

Some or all of the following symbols may appear on the

engine or equipment, or in this manual.

Read Manual

Fire

Moving Parts

Toxic Fumes

Explosion

Shock

Hazard Chemical

Kickback

Hot Surface

Wear Protective Eye Protection

Not for

Reproduction

5

en

Operator Safety

11. It is advisable to wear protective headgear to prevent

the possibility of being struck by small flying particles,

or being struck by low hanging branches, twigs, or other

objects which may be unnoticed by the operator.

12. Do not operate the walk-behind mower without proper

guards or other safety protective devices in place.

13. Use this equipment only for its intended purpose. Do not

operate the mower over loose material, such as gravel,

sticks, rubbish, etc., that cause risk of thrown objects

and damage to the mower.

14. See manufacturer’s instructions for proper operation

and installation of accessories. Only use accessories

approved by the manufacturer.

15. Operate only in daylight or good artificial light.

16. Do not operate the walk-behind mower while under the

influence of alcohol, drugs or other medication which

can cause drowsiness or affect your ability to operate

this machine safely.

17. Never operate walk-behind mower in wet grass. Always

be sure of your footing; keep a firm hold on the handle

and walk; never run.

18. Before each use, inspect the throttle control lever and

cable. Make sure that the cable is free and that the lever

is not damaged. Also check the cable linkage running to

the carburetor for kinks, loose fittings, and obstructions.

19. Stop the engine (motor) when crossing gravel drives,

walks, or roads.

20. Watch for traffic when operating near, or when crossing

roads.

21. Stop the engine (motor) whenever you leave the

equipment, before cleaning repairing or inspecting the

unit, be sure that all moving parts have stopped. Let the

engine cool, disconnect the spark plug wire and move it

away from the spark plug.

22. If the equipment should start to vibrate abnormally,

stop the engine (motor), disconnect the spark plug wire

and prevent it from touching the spark plug. Check

immediately for the cause. Vibration is generally a

warning of trouble.

23. After striking a foreign object, stop the engine (motor).

Remove the wire from the spark plug. Inspect the walk

behind mower for damage. If damaged, repair before

starting and operating the walk-behind mower.

24. Regularly inspect the walk-behind mower. Make sure

parts are not bent, damaged or loose.

25. Never pick up or carry the walk-behind mower while the

engine is running.

26. Prolonged exposure to noise and vibration from petrol

engine powered equipment should be avoided. Take

intermittent breaks and/or wear ear protection from

engine noise as well as heavy work gloves to reduce

vibration in the hands.

OWNER’S INFORMATION

Know your product: If you understand the unit and how

the unit operates, you will get the best performance. As

you read this manual, compare the illustrations to the unit.

Learn the location and the function of the controls. To help

prevent an accident, follow the operating instructions and

the safety rules. Keep this manual for future reference.

RESPONSIBILITY OF THE OWNER

WARNING

This cutting machine is capable of throwing objects.

Failure to observe the following safety instructions

could result in serious injury to the operator or

bystanders.

The responsibility of the owner is to follow the

instructions below.

SAFE OPERATION PRACTICES

For Pedestrian Controlled Rotary Walk-behind Mowers

I. General Operation

1. Read, understand, and follow all instructions on the

machine and in the manual(s). Be thoroughly familiar

with the controls and the proper use of the walk-behind

mower before starting.

2. Familiarize yourself with all of the safety and operating

decals on this equipment and on any of its attachments

or accessories.

3. Do not put hands or feet near or under rotating parts.

4. Only allow responsible individuals, who are familiar with

the instructions, to operate the walk-behind mower.

5. Inspect the area where the mower is to be used. Your

equipment can propel small objects at high speed

causing personal injury or property damage. Stay away

from breakable objects, such as house windows, auto

glass, greenhouses, etc.

6. Keep the area of operation clear of all persons,

particularly small children, and pets.

7. Wear appropriate clothing such as a long-sleeved shirt

or jacket. Also wear long trousers or slacks. Do not wear

shorts.

8. Do not wear loose clothing which could get caught in

this equipment.

9. Always wear safety goggles or safety glasses with side

shields when operating walk-behind mower to protect

your eyes from foreign objects which can be thrown

from the unit.

10. Always wear work gloves and sturdy footwear. Leather

work shoes or short boots work well for most people.

These will protect the operator’s ankles and shins from

small sticks, splinters, and other debris, and improve

traction.

Not for

Reproduction

6

www.BRIGGSandSTRATTON.com

Operator Safety

II. Slope Operation

Slopes are a major factor related to slip and fall accidents

which can result in severe injury. All slopes require extra

caution. If you feel uneasy on a slope, do not mow it.

Do mow across the face of slopes; never up and down.

Do remove objects such as rocks, tree limbs, etc.

Do watch for holes, ruts, or bumps. Tall grass can hide

obstacles.

Do not mow near drop-offs, ditches, or embankments. The

operator could lose footing or balance.

Do not mow excessively steep slopes.

Do not mow excessively steep slopes (maximum 10

degrees) or areas where the ground is very rough. Exercise

extreme caution when changing direction on slopes.

Do not mow on wet grass. Reduced footing could cause

slipping.

III. Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

mower and the mowing activity. Never assume that children

will remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of a responsible adult.

2. Be alert and turn walk-behind mower off if children enter

the area.

3. Before and while moving backwards, look behind and

down for small children.

4. Never allow children to operate the walk-behind mower.

5. Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision, trees, or

other objects that may obscure vision.

IV. Service

1. Use extra care in handling petrol and other fuels. They

are flammable and vapors are explosive.

a. Use only an approved container.

b. Never remove fuel cap or add fuel with the engine

running. Allow engine to cool before refueling. Do not

smoke.

c. Never refuel the machine indoors.

d. Never store the machine or fuel container inside

where there is an open flame, such as a water

heater.

e. If the fuel tank has to be drained, this should be done

outdoors. The drained fuel should be stored in a

container specifically designed for fuel storage or it

should be disposed of carefully.

f Old oil and petrol should be carefully poured into

containers especially designed for oil and fuel.

g. Filled containers should be carefully transported to a

collection center for proper recycling.

2. Never run an engine indoors or inside a closed area.

3. Never make adjustments or repairs with the engine

(motor) running. Disconnect the spark plug wire, and

keep the wire away from the plug to prevent accidental

starting (remove the ignition key if equipped with an

electric start). Always wear eye protection when you

make adjustments or repairs.

4. Check the engine mounting bolts at frequent intervals

for proper tightness.

5. Keep all nuts and bolts tight and keep equipment in

good condition. If items are replaced, make sure the

mounting fasteners are tight.

6. Never tamper with safety devices. Check their proper

operation regularly.

7. When servicing or repairing the walk-behind mower,

do not tip the machine over or up unless specifically

instructed to do so in this Manual. Service and repair

procedures can be done with the walk-behind mower

in an upright position. Some procedures will be easier

if the machine is lifted on a raised platform or working

surface.

8. To reduce fire hazard, keep walk-behind mower free of

grass, leaves, or other debris build-up. Clean up oil or

fuel spillage. Allow walk-behind mower to cool before

storing.

9. Stop and inspect the equipment if you strike an object.

Repair, if necessary, before restarting.

10. Always disconnect spark plug wire before cleaning,

repairing, or adjusting.

11. Do not change the engine governor setting or over--

speed the engine.

12. Clean and replace safety and instruction decals as

necessary.

13. To guard against engine overheating, always have

engine debris filter mounted and clean.

14. Inspect walk-behind mower before storage.

15. Use only original equipment or authorized replacement

parts.

16. Replace the cutting blade with factory authorized part.

Not for

Reproduction

7

en

Assembly

DESCRIPTION

The walk-behind lawn mower is an engine powered rotary

type mower. The engine drives a cutting blade located

under the mower housing. The blade lifts and cuts through

the grass. The height of cut can be adjusted to give the

lawn the desired finish. The cut pieces of grass are either

collected into a rear mounted grass bag or, on some

mowers, it can be recycled to feed the lawn. Recycling the

cut grass is known as “mulching”. Push models require the

operator to push the mower. Self-propelled models have a

rear wheel drive system to make mowing easier.

INTENDED USE/LIMITS OF USE

The walk-behind lawn mower is designed to cut lawn

grass. Any other use is not permitted. It is not designed

to cut grass over 15 cm in length or grass mixed with tall

weeds. The lawn mower is only suitable for private use in a

domestic garden. It is not suitable for cutting grass in public

parks or playing fields.

For assistance with any questions during assembly, please

contact the retailer or service dealer for the unit. Note that

references to “left” and “right” in this manual are from the

operating position.

REMOVE LAWN MOWER FROM CARTON

1. Remove the parts bag and any other loose parts packed

in the carton.

2. Cut the corners of the carton and lay the end panels flat.

3. Remove all packing materials except the padding

between the upper and lower handles and the padding

holding the control bar to the upper handle.

4. Roll the lawn mower off the carton. Check the carton

thoroughly for any additional parts that may have

loosened during shipment.

Operator Safety

SAFETY DECALS

Before operating your walk-behind lawn mower, read the

safety decals installed on your lawn mower. The cautions

and warnings are for your safety. To avoid a personal injury

or damage to your walk-behind lawn mower, understand

and follow all the safety decals.

If any safety decals become worn or damaged and cannot

be read, order replacement decals from your local dealer.

A — Part No. L0101040 Warning Icon Decal

A

Figure 1

Not for

Reproduction

8

www.BRIGGSandSTRATTON.com

Assembly

ASSEMBLE THE HANDLE

1. Loosen the lower handle knobs (A, Fig. 2) at the left and

right handle brackets.

2. Raise the lower handle section to the operating position,

and then tighten the lower handle knobs securely.

NOTICE: Unfold the handle carefully to avoid pinching

and damaging the control cables.

A

Figure 2

3. Remove the protective padding. Loosen the upper

handle knobs (B, Fig. 3) securing the upper handle to

the lower handle.

4. Raise the upper handle section to the operating

position, and then tighten the upper handle knobs

securely.

5. Remove the packing material from the control bar.

B

Figure 3

After assembly, the handle height may be adjusted for

mowing comfort. See Operation section.

ASSEMBLE THE GRASS CATCHER

1. Insert the grass catcher frame into the bag with the rigid

floor of the bag to the bottom. Make sure the frame

handle (C, Fig. 4) is outside of the bag and toward the

top.

2. Snap the vinyl retainers (D) over each bar of the frame

opening (E).

C

D

E

Figure 4

Not for

Reproduction

9

en

Features and Controls

A - OPERATOR PRESENCE CONTROL BAR – must be

held down against the handle to start the engine and

operate the lawn mower. Release it to stop the engine.

B - DRIVE CONTROL BAR – must be held up against the

handle to engage the rear-wheel drive system.

C - THROTTLE CONTROL – adjusts engine speed from

slow to fast.

D - STARTER HANDLE – pull to start the engine.

E - HEIGHT ADJUSTMENT LEVER – single lever raises or

lowers all four wheels at once to provide different cutting

heights.

F - MODEL IDENTIFICATION LABEL – located on rear of

mower housing.

G - DRIVE SPEED CONTROL – adjusts drive speed from

slow to fast (if equipped).

H - GRASS CATCHER – mounts over the discharge

opening to collect grass debris.

I - MULCHING PLUG (sold separately) – inserted into

the discharge opening to allow mulching operation.

Figure 5

A

D

E

B

C

F

G

H

Not for

Reproduction

10

www.BRIGGSandSTRATTON.com

Operation

NOTICE: The engine was shipped from Briggs & Stratton

without oil. Before you start the engine, make sure you add

oil according to the instructions in this manual. If you start

the engine without oil, it will be damaged beyond repair and

will not be covered under warranty.

OIL RECOMMENDATIONS

See engine operator’s manual for complete oil

recommendations.

HOW TO CHECK/ADD OIL

See Specifications section for oil capacity.

1. Be sure lawn mower is level. Clean the oil fill area of

any debris.

2. Remove the dipstick and wipe with a clean cloth. Insert

and tighten the dipstick.

3. Remove the dipstick again and check the oil level. It

should be at the top of the full mark on the dipstick.

4. If the oil level is low, add oil slowly into the engine oil

fill. Do not overfill. After adding oil, wait one minute then

recheck the oil level.

5. Replace and tighten the dipstick.

FUEL RECOMMENDATIONS

See engine operator’s manual for complete fuel

recommendations.

WARNING

Operating any lawn mower can result in dust, debris, or foreign objects being thrown into the eyes,

which can result in severe eye injury. Always wear safety glasses while operating the lawn mower and

while performing any adjustments or repairs.

HOW TO ADD FUEL

WARNING

Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe

burns or death.

When Adding Fuel

• Turn engine off and let it cool at least 2 minutes before

removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area. Do Not

smoke while refueling

• Do not overfill fuel tank. To allow for the expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat,

and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks

or leaks. Replace with like parts, if necessary.

• If fuel spills, wait until it evaporates before starting engine.

• Store fuel in containers specifically designed for this

purpose.

Before filling the fuel tank for the first time, remove and

discard the debris plug located in the filler neck of the tank.

1. Stop the engine and let it cool at least 2 minutes before

refueling.

2. Clean the fuel cap area of dirt and debris. Remove the

fuel cap.

3. Fill the fuel tank with petrol. To allow for the expansion

of the fuel, do not fill above the bottom of the fuel tank

neck.

4. Reinstall the fuel cap securely.

Not for

Reproduction

11

en

Operation

HOW TO START THE LAWN MOWER

WARNING

Rapid retraction of starter cord

(kickback) will pull hand and arm

toward engine faster than you can let

go. Broken bones, fractures, bruises,

or sprains could result.

• When starting engine, pull the starter cord slowly until

resistance is felt and then pull rapidly to avoid kickback.

WARNING

Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe

burns or death.

When Starting Engine:

• Ensure that spark plug, muffler, fuel cap, and air cleaner are

in place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position, and

then crank until engine starts.

WARNING

Engines give off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause

nausea, fainting, or death

• Start and run engine outdoors.

• Do not start or run engine in an enclosed area, even if doors

or windows are open.

The lawn mower engine is equipped with ReadyStart®,

which features a temperature-controlled automatic choke.

It does not have a manual choke or primer system.

1. Make sure the drive control bar is disengaged.

2. Move the throttle control to the FAST position.

3. Hold the operator presence control bar down against

the handle.

4. Firmly hold the starter cord handle. Pull the starter cord

handle slowly until resistance is felt, then pull rapidly.

If the engine fails to start after repeated attempts, see

Troubleshooting section.

HOW TO STOP THE LAWN MOWER

1. To immediately stop the engine and cutting blade,

release the operator presence control bar located on

the upper handle.

2. For normal stopping, move the drive speed control to

SLOW, and then release the drive control bar. Move the

throttle control to SLOW, and then release the operator

presence control bar.

HOW TO ADJUST THE ENGINE SPEED

The throttle control is located on the right side of the upper

handle. The control has positions for SLOW and FAST. For

best mulching and bagging results, always mow with the

throttle in the FAST position.

HOW TO OPERATE THE DRIVE SYSTEM

The rear-wheel drive system consists of a drive control bar

and a drive speed control (if equipped with the variable

speed feature) located on the left side of the upper handle.

The drive system propels the lawn mower forward only; it

does not propel in reverse.

1. Lift the drive control bar (A, Figure 6) up against the

handle to engage the rear-wheel drive system.

2. Adjust the drive speed control (B) to the desired speed.

3. Release the drive control bar to disengage the drive

system.

A

B

Figure 6

NOTICE: To avoid wear and damage to the drive system,

always hold the drive control bar firmly against the handle

while mowing. Adjust the drive speed control only when the

drive system is engaged.

Not for

Reproduction

12

www.BRIGGSandSTRATTON.com

Operation

HOW TO ADJUST THE HANDLE

The height of the lawn mower handle can be adjusted to

either of two positions for operator comfort.

1. Loosen the lower handle knobs (A, Figure 7) at the left

and right handle brackets.

A

Figure 7

2. Adjust the handle to the desired position.

3. Tighten the lower handle knobs securely.

HOW TO ADJUST THE CUTTING HEIGHT

A single-point height adjustment lever is located above the

right rear wheel. Changing the position of the lever will raise

or lower the mower housing for different cutting heights.

WARNING

Shut off the engine and wait for the blade to come to

a complete stop before changing the position of the

height adjuster lever.

1. Pull the lever (B, Figure 8) away from the locking tab.

2. Move the lever forward or backward until the mower

housing is at the desired height.

3. Release the lever and make sure it engages the locking

tab.

A

B

Figure 8

NOTICE: To avoid damage to the blade or engine, do not

use the lowest cutting height in areas where rocks, tree

roots, or other embedded obstructions are present.

HOW TO INSTALL AND REMOVE THE GRASS

CATCHER

WARNING

Do not operate the lawn mower unless the mulching

plug or grass catcher is installed.

1. Remove the mulching plug, if installed.

2. To install the grass catcher, raise the door (A, Figure 9)

on the rear of the mower housing.

3. Fit the hooks (B) on each side of the grass catcher

frame into the slots in the door.

Figure 9

4. Lower the door over the grass catcher to secure it in

place.

5. To remove the grass catcher, grasp the frame handle

(C) and the rear edge of the bag, and then carefully lift it

away from the door.

The grass catcher will be heavy when filled with clippings.

To avoid unnecessary wear, do not drag it across the

ground when emptying.

A

B

C

Not for

Reproduction

13

en

Operation

HOW TO INSTALL AND REMOVE THE

MULCHING PLUG (IF EQUIPPED)

WARNING

Do not operate the lawn mower unless the mulching

plug or grass catcher is installed.

The mulching plug allows the blade to re-cut the grass

clippings within the mower housing so they are reduced in

size and will disperse into the grass. The mulched clippings

will biodegrade quickly to provide nutrients for the lawn.

Always mulch with your highest engine (blade) speed, as

this will provide the best re-cutting action of the blade.

1. Remove the grass catcher, if installed.

2. To install the mulching plug, raise the door on the rear

of the mower housing.

3. Insert the mulching plug into the discharge opening and

close the door.

4. To remove the mulching plug, raise the door and lift the

plug out of the discharge opening.

FOR BEST MOWING RESULTS

For regularly maintained grass

• Adjust the cutting height so that only the top one-third of

the grass is cut

• Operate the engine speed at FAST for best mulching or

bagging performance

• Change the cutting direction from one mowing to the next

to prevent patterns in the lawn

For very tall grass

• Raise the cutting height to a high position and adjust

the drive speed control to SLOW (if equipped) to avoid

plugging the mower housing with clippings

• Operate the engine speed at FAST for best mulching or

bagging performance

• If desired, mow the area a second time – perpendicular to

the first cutting – at a lower cutting height

For thick grass

• Reduce the width of cut and adjust the drive speed

control to SLOW (if equipped) to avoid plugging the

mower housing with clippings

• Operate the engine speed at FAST for best mulching or

bagging performance

• If desired, mow the area a second time – perpendicular to

the first cutting – at a lower cutting height

For wet grass

• Do not mow when the grass is wet

• Wet grass will not mulch or discharge into the grass

catcher effectively

• Wet grass tends to plug the mower housing and leave

clumps of clippings on the ground

Not for

Reproduction

14

www.BRIGGSandSTRATTON.com

NOTICE: If the engine is tipped during maintenance, the

fuel tank must be empty and the spark plug side must be

up. If the fuel tank is not empty and if the engine is tipped

in any other direction, it may be difficult to start due to oil or

fuel contaminating the air filter and/or spark plug.

WARNING

Make sure the engine and blade is stopped and that

the spark plug is disconnected before performing any

maintenance.

See the engine operator’s manual for all engine

maintenance information.

MAINTENANCE SCHEDULE

Before Each Use

Tighten any loose fasteners

Check for loose or worn blade. See authorized dealer

for replacement.

After Each Use

Clean and inspect grass catcher

Clean debris from mower housing

Every 10 Hours

Clean debris from drive belt cover

Inspect drive system

Every 25 Hours or Annually

Sharpen or replace cutting blade

Maintenance

HOW TO CLEAN AND INSPECT THE GRASS

CATCHER

Pores in the grass bag can become filled with dirt and

dust over time, causing the bag to collect less grass. After

each use, thoroughly empty the bag to prevent mildew.

Occasionally rinse the bag with fresh water and allow it to

completely air dry before use to keep the pores clean.

Normal use will cause gradual wear to the grass catcher.

Frequently check it for wear, damage, or deterioration,

which could expose moving parts or allow objects to

be thrown. Replace it as needed with like parts. Use

only those accessories specifically approved by the

manufacturer

HOW TO CLEAN THE MOWER HOUSING AND

DRIVE SYSTEM

WARNING

Shut off the engine and disconnect the spark plug

wire before inspecting, cleaning, or performing any

maintenance on the machine.

WARNING

The mower blade is sharp and can cause serious

injuries. Carefully wrap the blade or wear heavy

gloves while performing blade maintenance or other

work in the blade area.

1. Turn the lawn mower on its side, with the air filter side of

the engine facing up.

2. Wear heavy gloves and use an appropriate scraping

tool to remove debris that has collected underneath the

mower housing.

3. Occasionally remove the drive belt cover and clean

debris from the belt area. Then replace the cover

securely.

HOW TO INSPECT THE DRIVE SYSTEM

Keep the tires free of fuel, oil, or yard chemicals, which may

harm the rubber. If the tires are damaged, replace with like

parts.

Check the drive wheels to make sure they move freely. If

the wheels drag, or drive system doesn’t operate smoothly,

contact your retailer or factory-authorized dealer for service.

Not for

Reproduction

15

en

Maintenance

HOW TO SERVICE THE CUTTING BLADE

WARNING

Shut off the engine and disconnect the spark plug

wire before inspecting, cleaning, or performing any

maintenance on the machine.

WARNING

The blade is sharp and can cause serious injuries.

Carefully wrap the blade or wear heavy gloves while

performing blade maintenance or other work in the

blade area.

See your authorized dealer for all blade maintenance.

HOW TO PREPARE THE LAWN MOWER FOR

STORAGE

WARNING

Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe

burns or death

• When storing fuel or equipment with fuel in the tank, keep

it away from furnaces, stoves, water heaters, or other

appliances that have pilot lights or other ignition sources

because they can ignite fuel vapors

For extended storage, prepare the lawn mower as follows.

1. Drain the fuel from the tank into an approved container.

Run the engine until it stops from lack of fuel.

2. While the engine is still warm, change the engine oil.

3. Thoroughly clean the lawn mower of all dirt, debris, and

grass clippings underneath the mower housing.

4. Make sure all fasteners are secure.

5. Fold the handle down, if desired.

6. Store the lawn mower in a clean, dry location, free of

grass, leaves, or excessive grease. Do not cover the

lawn mower while the engine is warm.

Not for

Reproduction

16

www.BRIGGSandSTRATTON.com

Troubleshooting

PROBLEM LOOK FOR REMEDY

Engine does not start 1. Control bar not held down against handle 1. Press down and hold control bar to handle

2. Dirty air filter 2. Clean or replace the air filter

3. Out of fuel 3. Fill the fuel tank

4. Stale fuel; contaminates or water in fuel 4. Drain the tank and refill with fresh clean fuel

5. Spark plug wire is disconnected 5. Connect wire to spark plug

6. Spark plug fouled or not gapped correctly 6. Clean deposits from spark plug electrode

and check for proper gap

7. Loose blade bolt 7. Tighten blade bolt to 45 lb-ft (61 Nm)

Starter rope hard to

pull

1. Control bar not held down against handle 1. Press down and hold control bar to handle

2. Blade dragging in grass 2. Move lawn mower out of grass before

starting

3. Bent engine crankshaft. 3. Contact factory-authorized service dealer

Lawn mower is hard

to push or drive

system not effective

1. Cutting height is set too low 1. Raise cutting height

2. Grass catcher overloaded 2. Empty grass catcher bag

3. Mower housing is plugged with grass

clippings

3. Stop engine and disconnect spark plug wire;

clean underside of mower housing

4. Drive belt worn, broken, or slipped off

pulley

4. Contact factory-authorized service dealer

5. Debris plugging the drive wheel pinions 5. Contact factory-authorized service dealer

Engine lacks power 1. Cutting height is set too low 1. Raise cutting height

2. Grass is very thick 2. Reduce width of cut; raise cutting height

3. Engine speed set too low 3. Set engine speed to FAST

4. Dirty air filter 4. Clean or replace the air filter

5. Mower housing is plugged with grass

clippings

5. Stop engine and disconnect spark plug wire;

clean underside of mower housing

6. Drive speed is set too fast 6. Reduce drive speed

Grass does not cut

evenly; clumps of

grass deposited on

lawn

1. Blade is worn 1. Sharpen or replace blade

2. Cutting height is set too low 2. Raise cutting height

3. Grass is very thick 3. Reduce width of cut; raise cutting height

4. Engine speed set too low 4. Set engine speed to FAST

5. Drive speed is set too fast

5. Reduce drive speed

6. Mower housing is plugged with grass

clippings

6. Stop engine and disconnect spark plug wire;

clean underside of mower housing

7. Grass catcher overloaded 7. Empty grass catcher bag

8. Grass is too wet 8. Allow grass to dry before mowing

Excessive vibration 1. Bent or loose cutting blade 1. Replace blade or tighten blade bolt to 45 lb-in

(61 Nm)

2. Bent engine crankshaft 2. Contact factory-authorized service dealer

Not for

Reproduction

17

en

Warranty

Briggs & Stratton Power Products Group, L.L.C. Owner Warranty Policy

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the product that is defective in material or workmanship

or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is

effective for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in your area.

For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at www.BRIGGSandSTRATTON.com.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are

limited to one year from purchase, or to the extent permitted by law and and all implied warranties are excluded. Liability for incidental or

consequential damages are excluded to the extent exclusion is permitted by law. Some states or countries do not allow limitations on how long

an implied warranty lasts, and some states or countries do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to

state or country to country.

Warranty Period

Product Type Consumer Use Commercial Use:

Walk-behind Lawn Mower 2 Years 90 Days

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the

table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for

commercial, income producing or rental purposes. Once product has experienced commercial use, it shall thereafter be considered as commercial use

for purposes of this warranty.

No warranty registration is necessary to obtain warranty. Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the

time warranty service is requested, the manufacturing date of the product will be used to determine the warranty.

About Your Warranty

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most

warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not

apply to the product if damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation.

Similarly, the warranty is void if the serial number on the product has been removed or the product has been altered or modified.

This warranty covers product related defective material and/or workmanship only. To avoid misunderstanding which might occur between the customer

and the Dealer, listed below are some of the causes of product failure that the warranty does not cover.

• Normal Wear: Small Engine Powered Equipment, like all mechanical devices, needs periodic parts and service to perform well. Warranty does not

cover repair when normal use has exhausted the life of the product or part.

• Installation: This warranty does not apply to product that has been subjected to improper or unauthorized installation, alteration or modification. Nor

installations that prevent starting, cause unsatisfactory engine performance.

• Improper Maintenance: The life of this product depends upon the conditions under which it operates, and the care it receives. Recommended

maintenance and adjustment intervals are stated in the Operator’s Manual. Often product, such as tillers, edgers, rotary mowers, are used in dusty or

dirty conditions, which can cause what appears to be premature wear. Such wear, when caused by dirt, dust, or other abrasive material entering the

product because of improper maintenance is not covered by warranty. The warranty will not cover repairs due to problems caused by replacement

parts that are not original manufactured part(s).

• Incorrect and/or insufficient fuel or lubrication: This warranty does not cover damage caused by the use of stale fuel, or altered gasoline. Damage

to engine or engine components ie, combustion chamber, valves, valve seats, valve guides, burned starter motor windings caused by use of alternate

fuels such as liquefied petroleum, natural gas, are not covered unless engine is certified for this operation. Parts which are scored or broken because

product was operated with insufficient, contaminated or incorrect grade of lubricating oil as well as product components damaged due to lack of

lubrication are not covered.

• Operational Misuse: Proper operation of the product is stated in the Operator’s Manual. Product damaged by over speeding, overheating, or

operation in a confined area without sufficient ventilation. Product broken by excessive vibration caused by a loose engine mounting, loose or

unbalanced blades, impellers, over speeding, or bent crankshaft due to striking of solid object. Damage or malfunctions resulting from accidents,

abuse, or improper servicing or freezing or chemical deterioration, as well as operating in excess of recommended capacities as outlined in the

Operator’s Manual are not covered.

• Routine tune-up, wear items or adjustments: This warranty excludes wear items such as oil, belts, blades, o-rings, filters, etc.

• Other exclusions: Repair or adjustments for part(s) that are not manufactured by Briggs & Stratton are not covered. This warranty excludes failures due

to acts of God and other force majeure events beyond the manufacturers control. Also excluded are used, reconditioned, and demonstration products.

Warranty service is available only through Authorized Service Dealers. Locate your nearest dealer in our locator map at

BRIGGSandSTRATTON.COM.

Not for

Reproduction

18

www.BRIGGSandSTRATTON.com

Specifications

DESCRIPTION 19’’ / 48 cm Lawn Mower 21” / 53 cm Lawn Mower

Engine Briggs & Stratton Briggs & Stratton

875 Series 875 Series

Drive System Self-Propelled Self-Propelled

Single Speed Variable Speed

Cutting Width 480 mm 530 mm

Cutting Height 20-75 mm 25-76 mm

Height Adjusters 7 Position 7 Position

Grass Bag Capacity 65 L 70 L

Weight 42 kg 51 kg

Noise Level per 2000/14/EC (LWA) 96 dB(A) 98 dB(A)

Noise Level (LPA) 74 dB(A) 72.5 dB(A)

DESCRIPTION 19” / 48 cm Lawn Mower 21” / 53 cm Lawn Mower

Engine Briggs & Stratton Briggs & Stratton

Drive System Self-Propelled Self-Propelled

Variable Speed Variable Speed

Cutting Width 480 mm 530 mm

Cutting Height 20-75 mm 25-76 mm

Height Adjusters 7 Position 7 Position

Grass Bag Capacity 65 L 70 L

Weight 43 kg 51 kg

Noise Level per 2000/14/EC (LWA) 96 dB(A) 98 dB(A)

Noise Level (LPA) 74 dB(A) 72.5 dB(A)

DESCRIPTION 19” / 48 cm Lawn Mower 21” / 53 cm Lawn Mower

Engine Briggs & Stratton Briggs & Stratton

675 Series 675 Series

Drive System Self-Propelled Self-Propelled

Single Speed Single Speed

Cutting Width 480 mm 530 mm

Cutting Height 20-75 mm 25-76 mm

Height Adjusters 7 Position 7 Position

Grass Bag Capacity 65 L 70 L

Weight 43 kg 51 kg

Noise Level per 2000/14/EC (LWA) 96 dB(A) 98 dB(A)

Noise Level (LPA) 74 dB(A) 72.5 dB(A)

Not for

Reproduction

Walk-behind græsslåmaskine

Beskrivelse

Walk-behind græsslåmaskine, 48 cm (19”)

Walk-behind græsslåmaskine, 53 cm (21”)

Walk-behind græsslåmaskine, 48 cm (19”)

Walk-behind græsslåmaskine, 53 cm (21”)

Walk-behind græsslåmaskine, 48 cm (19”)

Walk-behind græsslåmaskine, 53 cm (21”)

Original vejledning

1752053

Revision: C

Milwaukee, WI, alle rettigheder forbeholdes.

Betjeningsvejledning

da

Not for

Reproduction

2

www.BRIGGSandSTRATTON.com

GENEREL INFORMATION

TAK fordi du valgte at købe denne kvalitetsgræsslåmaskine. Det glæder os at du har tillid til vores varemærke. Hvis du

bruger og vedligeholder dit produkt ifølge instruktionerne i denne vejledning, vil din græsslåmaskine give dig mange års

pålidelig drift.

SIKKERHED OG BEREGNET BRUG

Denne manual indeholder sikkerhedsinformation som gør dig opmærksom på farer og risici forbundet med

græsslåmaskiner samt hvordan de kan undgås. Denne maskine er kun konstrueret og beregnet til klipning af etablerede

græsplæner og er ikke beregnet til noget andet formål. Det er vigtigt, at du læser og forstår disse instruktioner fuldt ud inden

du forsøger at starte eller betjene udstyret. Gem disse originale anvisninger til fremtidig brug.

ENDELIG MONTERING

Visse enheder kan kræve endelig samling inden ibrugtagen. Se afsnittet Samling i denne manual for vejledning i hvordan

den samles færdig. Følg instruktionerne nøje.

PRODUKTSUPPORT

Du skal aldrig søge længe efter kvalitetssupport og service til din græsslåmaskine. Brug vores find nærmeste forhandler på

www.BRIGGSandSTRATTON.COM for at finde et autoriseret servicecenter i din nærhed eller kontakt forhandleren hvor

du købte produktet. Hvis du ønsker en illustreret reservedelsliste kan du gå til vores hjemmeside.

Produktidentifikationsmærkat

Part No. xxxxxxx

xxxxxxxxxxxxxxx

Serial No. xxxxxxxxxx

20xx

kW: x.xx

xxxx max

xxxxxxxxxxxxxxxxxxxxxxx

xxx dB

kg: xxx

A

B

C

D

E

F G

H

I

A. Producentens Identifikationsnummer

B. Producentens serienummer

C. Motoreffekt i kilowatt

D. Højeste motorhastighed i omdrejninger per minut

E. Fabrikantens navn og adresse

F. Fabrikationsår

G. CE-Mærke

H. Maskinens vægt i kilogram

I. Garanteret lydeffekt i decibel

Indtast nedenfor græsslåmaskinens model og

serienummer, som findes på mærkatet der er påklistret

bagpå græsslåmaskinen. Noter også købsdatoen

og vedhæft din kvittering som købsbevis i tilfælde af

at der kræves service på græsslåmaskinen indenfor

garantiperioden. Hav venligst disse numre ved hånden når

du kontkakter os med henblik på reservedele eller teknisk

assistance.

PRODUKTREFERENCEDATA

Model Beskrivelse Navn/Nummer

Apparatets SERIE-nummer

Forhandlernavn Købsdato

MOTORENS Reference Data

Motorfabrikat Motormodel

Motortype/Specif. Motorkode/Serienummer

Den illustrerede reservedelsliste til denne græsslåmaskine kan rekvireres fra din autoriserede forhandler. Vær venlig at

oplyse model og serienummer når du bestiller reservedele.

Not for

Reproduction

Stránka se načítá ...

Briggs & Stratton 881634 Uživatelský manuál

Tato příručka je také vhodná pro

Briggs & Stratton 881634 Uživatelský manuál

v jiných jazycích

Jiné dokumenty