Indesit BWE 81683X WSSS EU Uživatelská příručka

Značka: Indesit

Modelka: BWE 81683X WSSS EU

Kategorie: Pračky

Typ: Uživatelská příručka

WASHING MACHINE

Instructions for use

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water and electricity supplies

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Disposal

Opening the porthole door manually

Description of the washing machine, 6-7

Control panel

Display

Running a wash cycle, 8

Wash cycles and options, 9-10

Table of wash cycles

Wash options

Push & Wash

Detergents and laundry, 11-12

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Troubleshooting, 13

Service, 14

English,1

BWE 81683

IT FR

NL CZ

Italiano,15

Français,29

Deutsch,43

Nederlands,57

Česky,71

! This instruction manual should be kept in a safe

place for future reference. If the washing machine

is sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has

not been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with the

installation process.

3. Remov e t h e 4

protective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on

the rear part of the

appliance (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will need

them again if the washing machine needs to be

moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not

p e r f e c t l y l e v e l ,

c o m p e n s a t e f o r

any unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured in relation

to the worktop, must

not exceed 2°.

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

washing machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it

to a cold water tap

using a ¾ gas threaded

connection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2 . C o n n e c t t h e

inlet hose to the

washing machine by

screwing it onto the

corresponding water

inlet of the appliance,

which is situated on

the top right-hand side

of the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening

the duct supplied to

the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

•the socketisearthed and complies with all

applicable laws;

•thesocketisabletowithstandthemaximum

power load of the appliance as indicated in the

Technical data table (see opposite);

•thepowersupplyvoltagefallswithinthevalues

indicated in the Technical data table (see

opposite);

•the socket is compatible with the plug of

the washing machine. If this is not the case,

replace the socket or the plug.

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the washing machine has been installed,

the electricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle

with detergent and no laundry, using the wash

cycle “Auto Clean” (see “Cleaning the washing

machine”).

65 - 100 cm

Technical data

Model

BWE 81683

Dimensions

width 59.5 cm

height 85 cm

depth 60.5 cm

Capacity

from 1 to 8 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water

connections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1600 rotations per minute

Test wash

cycles in

accordance

with re-

gulations

1061/2010

and

1015/2010

Programme 9:

Eco Cotton 60°.

Programme 9:

Eco Cotton 40°.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU (WEEE)

Care and maintenance

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front

of the machine by

first pressing it in

the centre and then

pushing downwards

on both sides until

you can remove it

(see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figure):

a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

•Turnoffthewatertapaftereverywashcycle.

This will limit wear on the hydraulic system inside

the washing machine and help to prevent leaks.

•Unplugthewashingmachinewhencleaningit

and during all maintenance work.

Cleaning the washing machine

•Theouterpartsandrubbercomponents

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

•Thewashingmachinehasa“AutoClean”

programme for its internal parts that must be

run with no load in the drum.

For maximum performance you may want

to use either the detergent (i.e. a quantity

10% the quantity specified for lightly-soiled

garments) or special additives to clean the

washing machine. We recommend running a

cleaning programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards

(2) (see figure).

Wash it under running

water; this procedure

should be repeated

frequently.

Caring for the door and drum of your

appliance

•Alwaysleavetheportholedoorajarinorderto

prevent unpleasant odours from forming.

Precautions and tips

! This washing machine was designed and constructed

in accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

•Thisappliancewasdesignedfordomesticuseonly.

•Thisappliancecanbeusedbychildren

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

•Thewashingmachinemustonlybeusedbyadults,in

accordance with the instructions provided in this manual.

•Donottouchthemachinewhenbarefootorwithwetor

damp hands or feet.

•Donotpullonthepowersupplycablewhenunplugging

the appliance from the electricity socket. Hold the plug

and pull.

•Donotopenthedetergentdispenserdrawerwhilethe

machine is in operation.

•Donottouchthedrainedwaterasitmayreach

extremely high temperatures.

•Neverforcetheportholedoor.Thiscoulddamagethe

safety lock mechanism designed to prevent accidental

opening.

•Iftheappliancebreaksdown,donotunderany

circumstances access the internal mechanisms in an

attempt to repair it yourself.

•Alwayskeepchildrenwellawayfromtheappliancewhile

it is operating.

•Thedoorcanbecomequitehotduringthewashcycle.

•Iftheappliancehastobemoved,workinagroupoftwo

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

•Beforeloadinglaundryintothewashingmachine,make

sure the drum is empty.

Disposal

•Disposingofthepackagingmaterials:observelocal

regulations so that the packaging may be re-used.

• TheEuropeanDirective2012/19/EU-WEEEonWaste

Electrical and Electronic Equipment, requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials they

contain and reduce the impact on human health and the

environment. The crossed out “wheeled bin” symbol on

the product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their

old appliance.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if

it is not, remove excess

water using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel

on the lower front part of

the washing machine (see

figure).

4. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Description of the washing

machine

Control panel

TEMPERATURE

button

WASH

CYCLE

SELECTOR

KNOB

Detergent dispenser drawer

ON/OFF

button

SPIN

button

START/PAUSE

button

and indicator light

DELAYED

START

button

OPTION

buttons

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: press this briefly to switch the machine

on or off. The START/PAUSE indicator light which flashes

slowly in a green colour shows that the machine is switched

on. To switch off the washing machine during the wash cycle,

press and hold the button for approximately 3 seconds; if

the button is pressed briefly or accidentally the machine will

not switch off.

If the machine is switched off during a wash cycle, this wash

cycle will be cancelled.

PUSH & WASH button: (see “Wash cycles and options”).

WASH CYCLE SELECTOR KNOB: used to set the desired

wash cycle (see “Table of wash cycles”).

CHILD LOCK button: to activate the control panel lock,

press and hold the button for approximately 2 seconds.

When the indicator light is illuminated, the control panel

is locked (apart from the ON/OFF button). This means it

is possible to prevent wash cycles from being modified

accidentally, especially where there are children in the home.

To deactivate the control panel lock, press and hold the button

for approximately 2 seconds.

OPTION buttons: press to select the available options.

The indicator light corresponding to the selected option will

remain lit.

TEMPERATURE

40°

60°

button: press to reduce or completely

exclude the temperature; the value appears on the display.

SPIN button: press to reduce or completely exclude the

spin cycle; the value appears on the display.

DELAYED START button: press to set a delayed start

for the selected wash cycle; the delay period appears on

the display.

START/PAUSE button and indicator light: when the

green indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has begun the indicator light will

remain lit in a fixed manner. To pause the wash cycle, press

the button again; the indicator light will flash in an amber

colour. If the symbol is not illuminated, the door may be

opened. To start the wash cycle from the point at which it

was interrupted, press the button again.

Standby mode

This washing machine, in compliance with new energy saving

regulations, is fitted with an automatic standby system which

is enabled after about 30 minutes if no activity is detected.

Press the ON-OFF button briefly and wait for the machine

to start up again.

DISPLAY

PUSH & WASH

button

CHILD LOCK

button

The display is useful when programming the machine and provides a great deal of information.

The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED

START option has been set, the countdown to the start of the selected wash cycle will appear.

Pressing the corresponding button allows you to view the maximum spin speed and temperature values attained by the

machine during the set wash cycle, or the values selected most recently, if these are compatible with the set wash cycle.

The hour-glass flashes while the machine processes the data on the basis of the selected programme. After a maximum of

10 minutes, the icon remains lit in a fixed manner and the final amount of time remaining is displayed. The hour-glass icon

will then switch off approximately 1 minute after the final amount of time remaining has appeared.

The “wash cycle phases” corresponding to the selected wash cycle and the “wash cycle phase” of the running wash cycle

appear in section B:

Main wash

Rinse

Spin

Drain

The “delay” symbol , when lit, indicates that the set “delayed start” value has appeared on the display.

There are three levels in section C concerning the washing options.

DOOR LOCKED indicator light:

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before opening the

door.

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED symbol is switched

off the door may be opened.

Display

C (see “Wash options”)

Running a wash cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

3. CLOSE THE DOOR.

4. Press the “PUSH & WASH” button to start the wash

programme.

Traditional programming

1. SWITCH THE MACHINE ON. Press the button;

the START/PAUSE indicator light will flash slowly in a

green colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

3. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the relevant

compartments as described in “Detergents and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Use the WASH CYCLE

SELECTOR knob to select the desired wash cycle. A

temperature and spin speed is set for each wash cycle;

these values may be adjusted. The duration of the cycle

will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

40°

60°

Modify the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings

if they are compatible with the selected cycle. The

temperature can be decreased by pressing the

40°

60°

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

pressing the button, until it is completely excluded

(the “OFF” setting). If these buttons are pressed again,

the maximum values are restored.

! Exception: if the 6 programme is selected, the

temperature can be increased up to a value of 60°C.

! Exception: if the 7 programme is selected, the

temperature can be increased up to a value of 60°C.

! Exception: if the 10 programme is selected, the

temperature can be increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. When this option has been

activated, the symbol lights up on the display. To

remove the delayed start setting, press the button until

the text “OFF” appears on the display.

Modify the cycle settings.

• Pressthebuttontoenabletheoption;theindicator

light corresponding to the button will switch on.

• Pressthebuttonagaintodisabletheoption;the

indicator light will switch off.

! If the selected option is not compatible with the set

wash cycle, the indicator light will flash and the option

will not be activated.

! If the selected option is not compatible with another

previously selected option, the indicator light will

flash accompanied by a buzzer (3 beeps), and only

the latter option will be activated; the indicator light

corresponding to the activated option will turn on.

! The options may affect the recommended load value

and/or the duration of the cycle.

7. START THE WASH CYCLE. Press the START/

PAUSE button. The corresponding indicator light will

turn green, remaining lit in a fixed manner, and the door

will be locked (the DOOR LOCKED symbol will be lit).

To change a wash cycle while it is in progress, pause

the washing machine using the START/PAUSE button

(the START/PAUSE indicator light will flash slowly in an

amber colour); then select the desired cycle and press

the START/PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press

the START/PAUSE button again to restart the wash

cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END” on the display; when the

DOOR LOCKED symbol switches off the door may

be opened. Open the door, unload the laundry and

switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

Wash cycles and options

Table of wash cycles

Wash options

- If the selected option is not compatible with the set wash cycle,

the indicator light will flash and the option will not be activated.

- If the selected option is not compatible with another

previously selected option, the indicator light will flash

accompanied by a buzzer (3 beeps), and only the latter

option will be activated; the indicator light corresponding

to the activated option will turn on.

Stain removal

This option allows for selecting the type of dirt so as to

optimally adjust the cycle for removing the stains. The

following types of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages,

for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of

selected dirt.

Rapid

When this button is pressed the first time, the 20’ icon will light

up, when pressed the second time the 45’ icon lights up and

the third time the 60’ icon lights up. When pressed the fourth

time the 20’ icon lights up again.

1) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with regulations 1061/2010: set wash cycle 9 with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments

which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

For all Test Institutes:

3) Long wash cycle for cottons: set wash cycle 6 with a temperature of 40°C.

4) Synthetic program along: set wash cycle 7 with a temperature of 40°C.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

* If you select programme and exclude the spin cycle, the machine will drain only.

** The duration of the wash cycle can be checked on the display.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergents

Max. load (kg)

Residual

dampness %

Energy

consumption kWh

Total water lt

Cycle duration

Wash

Fabric

softener

Everyday 30° ECO

Daily cotton

30° 1200

 

4 - - - **

Daily synthetics

30° 1000

 

4.5 - - - **

Coloureds

30° 1000

 

4 - - - **

Delicates

30° 0

 

1 - - - **

Rapid 30min: to refresh lightly soiled garments quickly (not suitable for wool,

silk and clothes which require washing by hand).

30° 800

 

4.5 70 0.18 42 30’

Traditionals

Cotton (3): lightly soiled whites and delicate colours.

40°

(Max.60°)

1600

 

8 44 1.03 92 230’

Synthetics (4): lightly soiled resistant colours.

40°

(Max.60°)

1000

 

4.5 46 0.74 59 125’

Mixed

40° 1600

 

8 - - - **

Eco cotton 60°C (1): heavily soiled whites and resistant colours.

60° 1600

 

8 44 1.04 55.0 225’

Eco cotton 40°C (2): lightly soiled whites and delicate colours.

40° 1600

 

8 44 1.03 92 230’

White cotton: heavily soiled whites and resistant colours.

60°

(Max.90°)

1600

 

8 - - - **

Specials

Rapid

20° 800

 

1.5 - - - 20’

Rapid

40° 1200

 

4 - - - 45’

Rapid

60° 1000

 

8 - - - 60’

Duvet: for down-stuffed garments. 30° 1000

 

3.5 - - - **

Wool: for wool, cashmere, etc. 40° 800

 

2 - - - **

Anti odour

40° 1000

 

3.5 - - - **

Rinse + Spin - 1600 -



8 - - - **

Spin + Drain - 1600 - - 8 - - - **

Drain only * - OFF - - 8 - - - **

Push & Wash

This function allows for starting a wash cycle even when the machine is switched off without having to press the ON/OFF

button in advance, or after switching on the machine, without having activated any button and/or selector (otherwise, the

Push & Wash function will be deactivated). To start the Push & Wash cycle press and hold the relative button for 2 seconds.

The lit indicator light indicates that the cycle has started. This wash cycle is ideal for cotton or synthetic fabrics, as it washes

at a temperature of 30° and a maximum spin speed of 1000 rpm. Maximum load 4 kg. (Cycle duration 45’).

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and additives.

3. Start the programme by pressing and holding the Push & Wash button for 2 seconds. The relative indicator light turns

green and the door will lock (the DOOR LOCKED symbol turns on).

N.B.: starting the wash cycle through the Push & Wash button activates an automatic non-customisable cycle

recommended for cotton and synthetic fabrics. This programme does not allow for setting any additional options.

To open the door while an automatic cycle is under way, press the START/PAUSE button; if the DOOR LOCKED symbol

is switched off the door may be opened. Press the START/PAUSE button again to restart the wash cycle from the point at

which it was interrupted.

4. Once the programme is finished, the END indicator light turns on.

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct dose

of detergent: adding too much detergent will not necessarily

result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

! Do not use hand washing detergents because these create

too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent dispenser

drawer and pour in the

detergent or washing additive,

as follows.

Compartment 1: Do not pour detergent into the middle

compartment 1.

Compartment 2: Washing detergent (powder or liquid)

If liquid detergent is used, it is recommended that the

removable plastic partition A (supplied) be used for proper

dosage. If powder detergent is used, place the partition into

slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indicated

on the central pin.

Preparing the laundry

• Dividethelaundryaccordingto:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Emptyallgarmentpocketsandcheckthebuttons.

• Do not exceed thevalues listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Special wash cycles

Daily cotton: a 30°C cycle for cotton garments. It allows

for reducing consumption of energy for heating the water,

while guaranteeing excellent results. Suitable for lightly soiled

garments.

Daily synthetics: a 30°C cycle for synthetic garments. It

allows for reducing consumption of energy for heating the

water, while guaranteeing excellent results. Suitable for lightly

soiled garments.

Coloureds: a 30°C cycle that helps to preserve the colours;

suitable for coloured cotton and synthetic garments. It allows

for reducing consumption of energy for heating the water,

while guaranteeing excellent results. Suitable for lightly soiled

garments.

Delicates: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments.

Mixed: a 40°C cycle for washing cotton and synthetic

garments together. Suitable for lightly soiled underwear.

Rapid (programme 11) allows for varying the garment

treatment duration from 20’ to 60’.

- 20’: the wash cycle that refreshes your garments in a mere

20 minutes.

- 45’: a short cycle designed for washing cotton/synthetic

blend fabrics.

- 60’: The “60’” cycle is designed to wash moderately soiled

resistant cotton garments at 60° in an hour, with good

washing performance. For synthetic or mixed garments, we

recommend lowering the temperature down to 40°.

Duvet: to wash double or single duvets (the weight of which

should not exceed 3,5 kg), cushions or clothes padded with

goose down such as puffa jackets, use the special wash

programme number 12. We recommend that duvets are placed

in the drum with their edges folded inwards (see figure) and that

no more than ¾ of the total volume of the drum is used. To

achieve the best results, we recommend that a liquid detergent

is used and placed inside the detergent dispenser drawer.

Wool - Woolmark Apparel Care - Blue:

the wool wash cycle of this machine has been approved by

The Woolmark Company for the washing of wool garments

labelled as “hand wash” provided that the products are

washed according to the instructions on the garment label

and those issued by the manufacturer of this washing

machine. (M1127)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Anti odour: use programme 14 (Synthetics) for washing

garments with bad odours (e.g. smoke, sweat, fried food).

The programme is designed to remove bad odours while

preserving the fabric fibres.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs

the distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

Troubleshooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”),

make sure that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water (the text “H2O” on the

display).

The washing machine

continuously takes in and drains

water.

The washing machine does not

drain or spin.

The washing machine vibrates a

lot during the spin cycle.

The washing machine leaks.

The “option” and START/PAUSE

indicator lights flash rapidly and an

error code appears on the display

(e.g.: F-01, F-..).

There is too much foam.

Push & Wash does not activate.

Possible causes / Solutions:

•Theapplianceisnotpluggedintothesocketfully,ornotenoughtomakecontact.

•Thereisnopowerinthehouse.

•Thewashingmachinedoorisnotclosedproperly.

•TheON/OFFbuttonhasnotbeenpressed.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thewatertaphasnotbeenopened.

•Adelayedstarthasbeenset.

•Thewaterinlethoseisnotconnectedtothetap.

•Thehoseisbent.

•Thewatertaphasnotbeenopened.

•Thereisnowatersupplyinthehouse.

•Thepressureistoolow.

•TheSTART/PAUSEbuttonhasnotbeenpressed.

•Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor

(see “Installation”).

•Thefreeendofthehoseisunderwater(see “Installation”).

•Thewalldrainagesystemisnotfittedwithabreatherpipe.

If the problem persists even after these checks, turn off the water tap, switch the

appliance off and contact the Technical Assistance Service. If the dwelling is on one

of the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to prevent this inconvenience.

•Thewashcycledoesnotincludedraining:somecyclesrequirethedraining

process to be enabled manually.

•Thedrainhoseisbent(see “Installation”).

•Thedrainageductisclogged.

•Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).

•Thewashingmachineisnotlevel(see “Installation”).

•Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).

•Thewaterinlethoseisnotscrewedonproperly(see “Installation”).

•Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care

and maintenance”).

•Thedrainhoseisnotfixedproperly(see “Installation”).

•Switchoffthemachineandunplugit,waitforapproximately1minuteandthen

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

•Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext“for

washing machines” or “hand and machine wash”, or the like).

•Toomuchdetergentwasused.

• AfterswitchingonthemachineacontrolotherthanPush&Washwasactivated.

Switch the machine off and press the Push & Wash button.

Service

Before contacting the Technical Assistance Service:

• Checkwhetheryoucansolvetheproblemalone(see“Troubleshooting”).

• Restartthewashcycletocheckwhethertheproblemhasbeensolved.

• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentre.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

Sommario

Installazione, 16-17

Disimballo e livellamento

Collegamenti idraulici ed elettrici

Primo ciclo di lavaggio

Dati tecnici

Manutenzione e cura, 18

Escludere acqua e corrente elettrica

Pulire la lavabiancheria

Pulire il cassetto dei detersivi

Curare oblò e cestello

Pulire la pompa

Controllare il tubo di alimentazione dell’acqua

Precauzioni e consigli, 19

Sicurezza generale

Smaltimento

Apertura manuale della porta oblò

Descrizione della lavabiancheria, 20-21

Pannello di controllo

Display

Come effettuare un ciclo di lavaggio, 22

Programmi e opzioni, 23-24

Tabella dei programmi

Opzioni di lavaggio

Push & Wash

Detersivi e biancheria, 25-26

Cassetto dei detersivi

Preparare la biancheria

Programmi particolari

Sistema bilanciamento del carico

Anomalie e rimedi, 27

Assistenza, 28

Assistenza Attiva 7 giorni su 7

LAVABIANCHERIA

BWE 81683

Istruzioni per l’uso

Italiano

! È importante conservare questo libretto per

poterlo consultare in ogni momento. In caso di

vendita, di cessione o di trasloco, assicurarsi

che resti insieme alla lavabiancheria per infor-

mare il nuovo proprietario sul funzionamento e

sui relativi avvertimenti.

! Leggere attentamente le istruzioni: ci sono

importanti informazioni sull’installazione,

sull’uso

e sulla sicurezza.

Disimballo e livellamento

Disimballo

1. Disimballare la lavabiancheria.

2. Controllare che la lavabiancheria non abbia

subìto danni nel trasporto. Se fosse danneggia-

ta non collegarla e contattare il rivenditore.

3. Rimuovere le 4 viti

di protezione per il

trasporto e il gommino

con il relativo distan-

ziale, posti nella parte

posteriore (vedi figura).

4. Chiudere i fori con i tappi di plastica in dota-

zione.

5. Conservare tutti i pezzi: qualora la lavabian-

cheria debba essere trasportata, dovranno

essere

rimontati.

! Gli imballaggi non sono giocattoli per bambini.

Livellamento

1. Installare la lavabiancheria su un pavimento

piano e rigido, senza appoggiarla a muri, mobili

o altro.

2. Se il pavimento non

fosse perfettamente

orizzontale, compen-

sare le irregolarità

svitando o avvitando

i piedini anteriori (vedi

figura); l’angolo di

inclinazione, misurato

sul piano di lavoro, non

deve superare i 2°.

Un accurato livellamento dà stabilità alla

macchina ed evita vibrazioni, rumori e spo-

stamenti durante il funzionamento. In caso di

moquette o di un tappeto, regolare i piedini in

modo da conservare sotto la lavabiancheria

uno spazio sufficiente per la ventilazione.

Collegamenti idraulici ed elettrici

Collegamento del tubo di

alimentazione dell’acqua

1. Collegare il tubo

di alimentazione av-

vitandolo a un rubi-

netto d’acqua fredda

con bocca filettata

da 3/4 gas (vedi

figura).

Prima di allacciare,

far scorrere l’acqua

finché non sia limpi-

da.

2. Collegare il tubo

di alimentazione alla

lavabiancheria

avvitandolo all’appo-

sita presa d’acqua,

nella parte posteriore

in alto a destra (vedi

figura).

3. Fare attenzione che nel tubo non ci siano

né pieghe né strozzature.

! La pressione idrica del rubinetto deve esse-

re compresa nei valori della tabella Dati tecni-

ci (vedi pagina a fianco).

! Se la lunghezza del tubo di alimentazione

non fosse sufficiente, rivolgersi a un negozio

specializzato o a un tecnico autorizzato.

! Non utilizzare mai tubi già usati.

! Utilizzare quelli in dotazione alla macchina.

Installazione

Collegamento del tubo di scarico

Collegare il tubo di

scarico, senza pie-

garlo, a una condut-

tura di scarico o a

uno scarico a muro

posti tra 65 e 100

cm da terra;

oppure appoggiarlo

al bordo di un lavan-

dino o di una vasca,

legando la guida in

dotazione al

rubinetto (vedi figu-

ra). L’estremità libera

del tubo di scarico

non deve rimanere

immersa nell’acqua.

! È sconsigliato usare tubi di prolunga; se in-

dispensabile, la prolunga deve avere lo stes-

so diametro del tubo originale e non superare

i 150 cm.

Collegamento elettrico

Prima di inserire la spina nella presa della

corrente, accertarsi che:

• la presa abbia la messa a terra e sia a nor-

ma di legge;

• la presa sia in grado di sopportare il carico

massimo di potenza della macchina, indi-

cato nella tabella Dati tecnici (vedi a fianco);

• la tensione di alimentazione sia compresa nei

valori indicati nella tabella Dati tecnici (vedi a

fianco);

• la presa sia compatibile con la spina della

lavabiancheria. In caso contrario sostituire

la presa o la spina.

! La lavabiancheria non va installata all’aperto,

nemmeno se lo spazio è riparato, perché è

molto pericoloso lasciarla esposta a pioggia e

temporali.

! A lavabiancheria installata, la presa della

corrente deve essere facilmente raggiungibile.

! Non usare prolunghe e multiple.

! Il cavo non deve subire piegature o com-

pressioni.

! Il cavo di alimentazione deve essere sostitu-

ito solo da tecnici autorizzati.

Attenzione! L’azienda declina ogni responsabi-

lità qualora queste norme non vengano rispet-

tate.

Primo ciclo di lavaggio

Dopo l’installazione, prima dell’uso, effettuare

un ciclo di lavaggio con detersivo e senza bian-

cheria impostando il programma “Auto Pulizia”

(vedi “Pulire la lavabiancheria”).

65 - 100 cm

Dati tecnici

Modello

BWE 81683

Dimensioni

larghezza cm 59,5

altezza cm 85

profondità cm 60,5

Capacità

da 1 a 8 kg

Collega-

menti elet-

trici

Vedi targhetta caratteristi-

che tecniche applicata sulla

macchina

Collega-

menti idrici

pressione massima

1 MPa (10 bar)

pressione minima

0,05 MPa (0,5 bar)

capacità del cesto 62 litri

Velocità di

centrifuga

sino a 1600 giri al minuto

Programmi

controllo

secondo i

regolamenti

1061/2010 e

1015/2010

Programma 9;

Eco Cotone 60°C.

Programma 9;

Eco Cotone 40°C.

Questa apparecchiatura è

conforme alle seguenti Diret-

tive Comunitarie:

- 2004/108/CE (Compatibili-

tà Elettromagnetica)

- 2006/95/CE (Bassa Tensione)

- 2012/19/EU (WEEE)

Pulire la pompa

La lavabiancheria è dotata di una pompa

autopulente che non ha bisogno di manuten-

zione. Può però succedere che piccoli oggetti

(monete, bottoni) cadano nella precamera che

protegge la pompa, situata nella parte inferiore

di essa.

! Assicurarsi che il ciclo di lavaggio sia terminato

e staccare la spina.

Per accedere alla precamera:

1. rimuovere il pan-

nello di copertura sul

lato anteriore della

macchina premendo

verso il centro, quin-

di spingere verso il

basso da entrambe

i lati ed estrarlo (vedi

figure).

2. svitare il coperchio

ruotandolo in senso

antiorario (vedi figura):

è normale che fuorie-

sca un po’ d’acqua;

3. pulire accuratamente l’interno;

4. riavvitare il coperchio;

5. rimontare il pannello assicurandosi, prima di

spingerlo verso la macchina, di aver inserito i

ganci nelle apposite asole.

Controllare il tubo di alimentazio-

ne dell’acqua

Controllare il tubo di alimentazione almeno

una volta all’anno. Se presenta screpolature e

fessure va sostituito: durante i lavaggi le forti

pressioni potrebbero provocare improvvise

spaccature.

! Non utilizzare mai tubi già usati.

Manutenzione e cura

Escludere acqua e corrente elettrica

• Chiudere il rubinetto dell’acqua dopo ogni lavaggio.

Si limita così l’usura dell’impianto idraulico della

lavabiancheria e si elimina il pericolo di perdite.

•Staccare la spina della corrente quando si

pulisce la lavabiancheria e durante i lavori di

manutenzione.

Pulire la lavabiancheria

• La parte esterna e le parti in gomma possono

essere puliti con un panno imbevuto di acqua

tiepida e sapone. Non usare solventi o abrasivi.

• La lavabiancheria è dotata di un programma

di “Auto Pulizia” delle parti interne che deve

essere effettuato senza alcun tipo di carico

nel cesto.

Il detersivo (nella quantità pari al 10% di quella

consigliata per capi poco sporchi) o additi-

vi specifici per la pulizia della lavabiancheria,

potranno essere utilizzati come coadiuvanti nel

programma di lavaggio. Si consiglia di effettuare

il programma di pulizia ogni 40 cicli di lavaggio.

Per attivare il programma premere contempora-

neamente i tasti A e B per 5 sec. (vedi figura).

Il programma partirà automaticamente ed avrà

una durata di circa 70 minuti. Per fermare il ciclo

premere il tasto START/PAUSE.

Pulire il cassetto dei detersivi

Per estrarre il cassetto

premere la leva (1) e tirarlo

verso l’esterno (2) (vedi

figura).

Lavarlo sotto l’acqua

corrente; questa pulizia

va effettuata

frequentemente.

Curare oblò e cestello

• Lasciare sempre socchiuso l’oblò per evitare

che si formino cattivi odori.

Apertura manuale della porta oblò

Nel caso non sia possibile aprire la porta oblò a causa della

mancanza di energia elettrica e volete stendere il bucato,

procedere come segue:

1. togliere la spina dalla presa

di corrente.

2. verificate che il livello

dell’acqua all’interno della

macchina sia inferiore rispetto

all’apertura dell’oblò; in caso

contrario togliere l’acqua in

eccedenza attraverso il tubo

di scarico raccogliendola in

un secchio come indicato in

figura.

3. rimuovere il pannello di

copertura sul lato anteriore

della lavabiancheria (vedi

figura).

4. utilizzando la linguetta indicata in figura tirare verso

l’esterno fino a liberare il tirante in plastica dal fermo; tirarlo

successivamente verso il basso e contemporaneamente

aprire la porta.

5. rimontare il pannello assicurandosi, prima di spingerlo

verso la macchina, di aver inserito i ganci nelle apposite asole.

Precauzioni e consigli

! La lavabiancheria è stata progettata e costruita in

conformità alle norme internazionali di sicurezza. Queste

avvertenze sono fornite per ragioni di sicurezza e devono

essere lette attentamente.

Sicurezza generale

• Questo apparecchio è stato concepito esclusivamente

per un uso di tipo domestico.

•Questo apparecchio può essere usato da

bambini da 8 anni in su e da persone con

capacità fisiche, sensoriali o mentali ridotte

o con esperienza e conoscenze insufficienti

se sono supervisionati o se hanno ricevu-

to adeguata formazione in merito all’uso

dell’apparecchio in modo sicuro e capendo

i pericoli connessi. I bambini non devono

giocare con l’apparecchio. Manutenzione

e pulizia non devono essere effettuati dai

bambini senza supervisione.

• Non toccare la macchina a piedi nudi o con le mani o i

piedi bagnati o umidi.

• Non staccare la spina dalla presa della corrente tirando

il cavo, bensì afferrando la spina.

• Non aprire il cassetto dei detersivi mentre la macchina

è in funzione.

• Non toccare l’acqua di scarico, che può raggiungere

temperature elevate.

• Non forzare in nessun caso l’oblò: potrebbe danneg-

giarsi il meccanismo di sicurezza che protegge da

aperture accidentali.

• In caso di guasto, in nessun caso accedere ai mecca-

nismi interni per tentare una riparazione.

• Controllare sempre che i bambini non si avvicinino alla

macchina in funzione.

• Durante il lavaggio l’oblò tende a scaldarsi.

• Se dev’essere spostata, lavorare in due o tre persone

con la massima attenzione. Mai da soli perché la mac-

china è molto pesante.

• Prima di introdurre la biancheria controlla che il cestello

sia vuoto.

Smaltimento

•Smaltimento del materiale di imballaggio:

attenersi alle norme locali, così gli imballaggi potranno

essere riutilizzati.

• La direttiva Europea 2012/19/EU (WEEE) sui rifiuti di

apparecchia¬ture elettriche ed elettroniche (RAEE),

prevede che gli elettrodo¬mestici non debbano essere

smaltiti nel normale flusso dei rifiuti solidi urbani. Gli

apparecchi dismessi devono essere raccolti separata-

mente per ottimizzare il tasso di recupero e riciclaggio

dei materiali che li compongono ed impedire potenziali

danni per la salute e l’ambiente. Il simbolo del cestino

barrato è riportato su tutti i prodotti per ricordare gli

obblighi di raccolta separata. Quando si acquista una

nuova apparecchiatura equivalente si può consegnare

il RAEE al negoziante, che è tenuto a ritirarlo gratuita-

mente; i RAEE di “piccolissime dimensioni” (nessun lato

sopra i 25 cm) possono essere consegnati gratuitamen-

te ai negozianti anche se non si acquista nulla (solo nei

negozi con superficie di vendita superiore a 400 mq). Per

ulteriori informazioni sulla corretta dismissione degli elettro-

domestici i detentori potranno rivolgersi al servizio pubblico

preposto o ai rivenditori.

Pannello di controllo

Descrizione della lavabiancheria

Tasto

TEMPERATURA

MANOPOLA

PROGRAMMI

Cassetto dei detersivi

Tasto

ON/OFF

Tasto

CENTRIFUGA

Cassetto dei detersivi: per caricare detersivi e additivi (vedi

“Detersivi e biancheria”).

Tasto ON/OFF : premere brevemente il tasto per accen-

dere o spegnere la macchina. La spia START/PAUSE che

lampeggia lentamente di colore verde indica che la macchina

è accesa. Per spegnere la lavabiancheria durante il lavaggio è

necessario tenere premuto il tasto più a lungo, circa 3 sec.; una

pressione breve o accidentale non permetterà lo spegnimento

della macchina. Lo spegnimento della macchina durante un

lavaggio in corso annulla il lavaggio stesso.

Tasto PUSH & WASH: (vedi “Programmi e opzioni”).

MANOPOLA PROGRAMMI: per impostare il programma

desiderato (vedi “Tabella dei programmi”).

Tasto BLOCCO TASTI: per attivare il blocco del pannello di

controllo, tenere premuto il tasto per circa 2 secondi. Il simbolo

acceso indica che il pannello di controllo è bloccato.

In questo modo si impediscono modifiche accidentali dei

programmi (ad eccezione del tasto ON/OFF), soprattutto se in

casa ci sono dei bambini. Per disattivare il blocco del pannello

di controllo, tenere premuto il tasto per circa 2 secondi.

Tasti OPZIONE: per selezionare le opzioni disponibili. La spia

relativa all’opzione selezionata rimarrà accesa.

Tasto TEMPERATURA

40°

60°

: premere per ridurre o esclu-

dere la temperatura; il valore viene indicato nel display.

Tasto CENTRIFUGA : premere per ridurre o escludere

del tutto la centrifuga; il valore viene indicato nel display.

Tasto PARTENZA RITARDATA : premere per imposta-

re una partenza ritardata del programma prescelto; il ritardo

viene indicato nel display.

Tasto e spia START/PAUSE : quando la spia verde lam-

peggia lentamente, premere il tasto per avviare un lavaggio.

A ciclo avviato la spia diventa fissa. Per mettere in pausa il

lavaggio, premere nuovamente il tasto; la spia lampeggerà

con colore ambra. Se il simbolo non è illuminato, si potrà

aprire l’oblò. Per far ripartire il lavaggio dal punto in cui è

stato interrotto, premere nuovamente i tasto.

Modalità stand by

Questa lavatrice, in conformità alle nuove normative

legate al risparmio energetico, è dotata di un sistema di

autospegnimento (stand by) che entra in funzione dopo circa

30 minuti nel caso di non utilizzo. Premere brevemente il

tasto ON-OFF e attendere che la macchina si riattivi.

Tasto e spia

START/PAUSE

DISPLAY

Tasto

PARTENZA

RITARDATA

Tasti

OPZIONE

Tasto

PUSH & WASH

Tasto

BLOCCO

TASTI

Stránka se načítá ...

Indesit BWE 81683X WSSS EU Uživatelská příručka

Značka: Indesit

Modelka: BWE 81683X WSSS EU

Kategorie: Pračky

Typ: Uživatelská příručka

Stáhnout PDF

zpráva

Indesit BWE 81683X WSSS EU Uživatelská příručka

Indesit BWE 81683X WSSS EU Uživatelská příručka

Související papíry

Jiné dokumenty