Yamaha AX-392 Uživatelský manuál

Yamaha
Značka
Yamaha
Modelka
AX-392
Kategorie
Audio zesilovače
Typ
Uživatelský manuál
Natural Sound Stereo Integrated Amplifier
Préampli/ampli de puissance stéréo de la série “Natural Sound”
Natural Sound Stereo-Verstärker
Natural Sound Integrerad Stereo Förstärkare
Amplificatore integrato stereo a Suono Naturale
Amplificador integrado estéreo de Sonido Natural
Natural Sound Geïntegreerde Stereo Versterker
AX-392
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
B G R T
2
●
Remote Control Transmitter
●
Emetteur de télécommande
●
Fernbedienung
●
Fjärrkontroll
●
Telecomando
●
Transmisor del control remoto
●
Afstandbediening
●
Batteries (size AA, R6, UM-3)
●
Piles (taille AA, R6, UM-3)
●
Batterien (Größe AA, R6, UM-3)
●
Batterier (storlek AA, R6, UM-3)
●
Batterie (dimensioni AA, R6, UM-3)
●
Pilas (tamaño AA, R6, UM-3)
●
Batterijen (maat AA, R6, UM-3)
SUPPLIED ACCESSORIES
●
After unpacking, check that the following parts are contained.
ACCESSOIRES FOURNIS
●
Après le déballage, vérifier que les pièces suivantes sont incluses.
MITGELIEFERTES ZUBEHÖR
●
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
MEDFÖLJANDE TILLBEHÖR
●
Kontrollera efter det apparaten packats upp att följande delar finns med.
ACCESSORI IN DOTAZIONE
●
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
ACCESORIOS INCLUIDOS
●
Desembale el aparato y verificar que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES
●
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
YAMAHA HiFi SYSTEM
REMOTE CONTROL TRANSMITTER
MD
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
AUX
PRESET
A/B/C/D/E
–+
SLEEP
TAPE
A/B
TUNER
CD
PHONO
POWER
3
English
Thank you for selecting this YAMAHA stereo amplifier.
● 60W + 60W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz
● High Dynamic Power, Low Impedance Drive Capability
● Continuously Variable LOUDNESS Control
● CD DIRECT AMP Switch to Reproduce the Purest CD Sound
● Remote Control Capability
SUPPLIED ACCESSORIES ..............................................................................2
FEATURES.........................................................................................................3
CAUTION ...........................................................................................................4
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER ............................5
CONNECTIONS ................................................................................................6
CONTROLS AND THEIR FUNCTIONS .............................................................8
OPERATIONS ..................................................................................................11
TROUBLESHOOTING .....................................................................................14
SPECIFICATIONS ...........................................................................................15
FEATURES
CONTENTS
4
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the cabinet will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in well-
ventilated condition. Be sure to allow a space of at least 10
cm behind, 10 cm on the both sides and 20 cm above the
top panel of the unit. Otherwise it may not only damage the
unit, but also cause fire.
6. Always set the VOLUME control to “–
∞
” before starting
the audio source play: increase the volume gradually to an
appropriate level after the play has been started.
7. Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
9. When not planning to use this unit for long periods of
time (ie., vacation, etc.), disconnect the AC power plug
from the wall outlet.
10.To prevent lightning damage, disconnect the AC power
plug and antenna cable when there is an electrical storm.
11.Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
12.Do not connect audio equipment to the AC outlet on the
rear panel if the equipment requires more power than the
outlet is rated to provide.
13.Voltage Selector (China and General Models only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space
below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode.
In this state, this unit is designed to consume a very small
quantity of power.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L
or coloured RED. Making sure that neither core is
connected to the earth terminal of the three pin plug.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED;
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
MAINS
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
A OR B : 4
Ω
MIN. /SPEAKER
A B : 8
Ω
MIN. /SPEAKER
SPEAKERS
A
B
AC OUTLETS
SWITCHED
l00W MAX. TOTAL
A OR B : 8
Ω
MIN. /SPEAKER
A B : 12
Ω
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
IMPEDANCE SELECTOR
(Europe model)
5
English
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
●
Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
Notes
●
There should be no large obstacles between the remote
control transmitter and the main unit.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
1
3
2
30°
30°
Remote control
sensor
Within approximately
6 m (19.7 feet)
6
CONNECTIONS
Never plug in this unit and other components until all connections are completed.
●
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this
unit.
●
If you have YAMAHA components numbered as 1, 2, 3, 4, etc. on the rear panel, connections can be made easily by only
connecting the output (or input) terminals of each component to the same-numbered terminals of this unit.
*
1
,
*
2
: Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 7.
MDPHONO
CD
TUNER AUX TAPE
PLAY REC PLAY REC
21 3 43 4
GND
MAINS
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
A OR B : 4
Ω
MIN. /SPEAKER
A B : 8
Ω
MIN. /SPEAKER
SPEAKERS
A
B
AC OUTLETS
SWITCHED
l00W MAX. TOTAL
A OR B : 8
Ω
MIN. /SPEAKER
A B : 12
Ω
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
OUTPUT
LINE OUT
LINE IN
LINE OUT
LINE IN
AUDIO OUT
OUTPUT
GND
OUTPUT
Right
(Europe model)
Tape deck, etc.MD recorder, etc.
Tuner
Left
Speakers A
Right
Left
Speakers B
To AC outlet
Turntable
CD player
Video cassette player,
LD player, etc.
*
2
*
1
7
English
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and lack bass. Do
not let the bare speaker wires touch each other or the
metal parts of this unit as this could damage this unit
and/or speakers.
How to Connect:
Red: positive (+)
Black: negative (–)
➀
Unscrew the knob.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Tighten the knob and
secure the wire.
●
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
●
Use speakers with the specified impedance shown on the
rear of this unit.
● <China and General models only>
Banana Plug connections are also possible. Simply insert
the Banana Plug connector into the corresponding terminal.
CONNECTING SPEAKERS
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S) (SWITCHED)
(Europe, China and General models)
.......................................................... 3 SWITCHED OUTLETS
(U.K. model) ........................................ 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
STANDBY/ON switch or the provided remote control
transmitter’s POWER key. These outlets will supply power to
any component whenever this unit is turned on.
The maximum power (total power consumption of components)
that can be connected to the SWITCHED AC OUTLET(S) is
100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
1
2
3
Be sure to switch this only when the power to this unit is not
on.
Select the position whose requirements your speaker system
meets.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE
STANDBY/ON SWITCH IS PRESSED;
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
(Upper position)
If you use one pair of speakers, the impedance of each
speaker must be 4Ω or higher.
If you use two pairs of speakers, the impedance of each
speaker must be 8Ω or higher.
(Lower position)
If you use one pair of speakers, the impedance of each
speaker must be 6Ω or higher.
If you use two pairs of speakers, the impedance of each
speaker must be 12Ω or higher.
IMPEDANCE SELECTOR switch
A OR B : 4
Ω
MIN. /SPEAKER
A B : 8
Ω
MIN. /SPEAKER
A OR B : 8
Ω
MIN. /SPEAKER
A B : 12
Ω
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
*
1
*
2
8
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
1 STANDBY/ON switch
Press this switch to turn the power to this unit on. Press it
again to turn this unit into the standby mode.
Standby mode
In this state, this unit consumes a very small quantity of
power to receive infrared-signals from the remote control
transmitter.
2 Power indicator
Lights up while the power to this unit is on.
3 Remote control sensor
Receives signals from the remote control transmitter.
4 SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
5 Input source indicators
The indicator for the source selected by the INPUT selector
lights up.
6 TAPE MONITOR indicator
Lights up while the TAPE MONITOR switch is on.
* When the tape deck (TAPE) is selected as the input source,
this indicator will not light up even if the TAPE MONITOR
switch is on.
7 TAPE MONITOR switch
When the tape deck connected to the TAPE terminals on the
rear of this unit is used for recording, you can monitor the
sounds being recorded by pressing TAPE MONITOR so that
TAPE MONITOR indicator lights up.
8 INPUT selector
When turned, selects a program source to listen to.
The input source indicator for the currently selected source
lights up.
9 CD DIRECT AMP switch
Press this switch inward to listen to a CD source in the purest
sound. (Refer to page 13 for details.)
0 VOLUME control
Used to raise or lower the volume level.
A PHONES jack
When you listen with headphones,
connect the headphones to the
PHONES jack.
When listening with headphones
privately, set both the SPEAKERS
A and B switches to the OFF
position.
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
LOUDNESS
SLEEP AUX TAPE MD CD TUNER PHONO TAPE
BASS
55
4
33
22
ll
0
4
TREBLE
55
4
33
22
ll
0
4
NATURAL SOUND STEREO AMPLIFIER
AX 392
SPEAKERS
PHONES
A
ON
B
OFF
VOLUMEINPUT
MONITOR
CD DIRECT AMP
l6
20
28
40
60
l2
8
4
2
0
–dB
STANDBY/ON
l
6
57
4
3
2
l
FLAT
l0
9
8
–
30dB
6547832190
AB C DE F
PHONES
9
English
B SPEAKERS switches
Set the switch A or B (or both A and B) for the speaker system
(connected to this unit) you will use to the ON position. Set the
switch for the speaker system you will not use to the OFF
position.
C Tone controls
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
D BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
E Continuously variable LOUDNESS control
Used to compensate for the human ears’ loss of sensitivity to
high and low-frequency ranges at low volume.
F Control door
See below for how to open and close the control door.
Open/close the control door
When it is not necessary to operate controls inside the control
door, close the door.
To open the door
To close the door
10
For Control of This Unit
1 SLEEP timer key
This unit is automatically turned into the standby mode one
hour after this key is pressed (so that SLEEP indicator lights
up).
2 POWER key
Turns the power to this unit on and turns this unit into the
standby mode alternately.
3 Input selector keys
Select input source.
4 VOLUME +/– keys
Turn the volume level up/down.
For Other Component Control
Identify the remote control transmitter keys with your
component’s keys. If these keys are identical, their functions
will be the same. For each key function, refer to the
corresponding instruction in your component’s manual.
1 Tape deck keys
Control tape deck.
* DIR A, B and A/B are applicable only to double
cassette tape deck.
* For a single cassette deck with automatic reverse
function, pressing DIR A will reverse the direction of
tape running.
2 Tuner keys
Control tuner.
+: Selects higher preset station number.
–: Selects lower preset station number.
A/B/C/D/E: Selects the group (A – E) of preset station
numbers.
3 CD player keys
Control compact disc player.
* DISC is applicable only to compact disc changer.
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of this unit. If the
CD player, tuner, tape deck, etc. connected to this unit are YAMAHA components designed for remote control compatibility, then this
remote control transmitter will also control various functions of each component.
YAMAHA HiFi SYSTEM
REMOTE CONTROL TRANSMITTER
MD
REC/PAUSE
DIR BDIR A
PLAY
DISC
VOLUME
PLAY
AUX
PRESET
A/B/C/D/E
–+
SLEEP
TAPE
A/B
TUNER
CD
PHONO
POWER
1
3
3
1
2
4
2
11
English
1
Set to the “∞” position.
2 Turn the power on.
3 Select a desired input source.
The indicator for the selected source lights up.
4 Select the speakers to be used.
*
If you use two speaker systems, press both the A and B
switches.
5 Play the source.
6
Adjust to the desired output level.
7 If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls or turn on the CD DIRECT AMP
switch. (Refer to page 13).
OPERATIONS
TO PLAY A SOURCE
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
LOUDNESS
SLEEP AUX TAPE MD CD TUNER PHONO TAPE
6
BASS
55
4
33
22
ll
0
4
TREBLE
55
4
33
22
ll
0
4
NATURAL SOUND STEREO AMPLIFIER
AX 392
SPEAKERS
PHONES
A
ON
B
OFF
VOLUMEINPUT
MONITOR
CD DIRECT AMP
l6
20
28
40
60
l2
8
4
2
0
–dB
STANDBY/ON
l
57
4
3
2
l
FLAT
l0
9
8
–
30dB
4
7 3
2
3 7
1, 6
Lights up.
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
STANDBY/ON
INPUT
CDMDTAPE TUNERAUX PHONO
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
SPEAKERS
A
ON
OFF
B
When you finish using this unit
Press the STANDBY/ON switch again to turn this unit into the
standby mode.
Standby mode
In this state, this unit consumes a very small quantity of
power to receive infrared-signals from the remote control
transmitter.
Note
If the TAPE MONITOR indicator is illuminated when you listen
to a source, press the TAPE MONITOR switch to turn off the
TAPE MONITOR indicator.
12
TO RECORD A SOURCE TO TAPE (OR MD)
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
LOUDNESS
SLEEP AUX TAPE MD CD TUNER PHONO TAPE
6
BASS
55
4
33
22
ll
0
4
TREBLE
55
4
33
22
ll
0
4
NATURAL SOUND STEREO AMPLIFIER
AX 392
SPEAKERS
PHONES
A
ON
B
OFF
VOLUMEINPUT
MONITOR
CD DIRECT AMP
l6
20
28
40
60
l2
8
4
2
0
–dB
STANDBY/ON
l
57
4
3
2
l
FLAT
l0
9
8
–
30dB
4
1 2
1 Select the source you want to record.
2 Play the source and then turn the VOLUME control up
to confirm the input source.
3 Begin recording on the tape deck (or MD recorder etc.)
connected to this unit.
4 If the tape deck connected to the TAPE terminals on the
rear of this unit is used for recording, you can monitor
the sounds being recorded by pressing the TAPE
MONITOR switch so that the TAPE MONITOR indicator
lights up.
Note
VOLUME, BASS, TREBLE, BALANCE, LOUDNESS controls
and CD DIRECT AMP switch settings have no effect on the
material being recorded.
TAPE
MONITOR
Lights up.
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
INPUT
CDMDTAPE TUNERAUX PHONO
1
13
English
Adjusting the BASS and TREBLE
controls
Adjusting the BALANCE control
Selecting the SPEAKER system
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Using the CD DIRECT AMP switch
Adjusting the continuously variable
LOUDNESS control
You can enjoy the purest possible CD sound from your CD
player by pressing this switch inward. By doing so, CD’s input
signals are sent to the built-in special amplifier for CD directly
bypassing the INPUT selector, the BASS, TREBLE,
BALANCE and LOUDNESS controls, and then sent to the
power amplifier. This signal routing reproduces the purest CD
sound eliminating any alterations to the CD signals.
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
1
2
3
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
SPEAKERS
A
ON
OFF
B
BASS
55
4
33
22
ll
0
4
TREBLE
55
4
33
22
ll
0
4
CD DIRECT AMP
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
LOUDNESS
57
4
3
2
l
FLAT
l0
9
8
6
–
30dB
LOUDNESS
57
4
3
2
l
FLAT
l0
9
8
6
–
30dB
Set to the “FLAT”
position.
Set to the loudest
listening level that you
would listen to.
Turn until the desired
volume is gained.
14
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
TROUBLESHOOTING
SYMPTOM
The unit fails to turn on when the
STANDBY/ON switch is pressed, or turns
into the standby mode suddenly soon after
the power is turned on.
It happens that this unit does not work
normally.
No sound.
The sound suddenly goes off.
Only one side speaker outputs the sound.
There is a lack of bass, and no ambience.
Sound “hums”.
The volume level is low while playing a
record.
The volume level cannot be increased, or
sound is distorted.
The sound is degraded when listening with
the headphones connected to the compact
disc player or tape deck that are connected
with this unit.
Sound level is low.
The input source cannot be changed,
though the INPUT selector is turned.
Using the BASS, TREBLE, BALANCE and
LOUDNESS controls does not affect the
tone.
The remote control transmitter does not
work.
The distance or range within which the
remote control transmitter can be used is
short.
CAUSE
Power cord is not plugged in or is not
completely inserted.
The IMPEDANCE SELECTOR switch on the
rear panel is not set to either end closely.
There is an influence of strong external noise
(lightning, excessive static electricity, etc.) or a
misoperation on this unit while using this unit.
Incorrect output cord connections.
Appropriate input source is not selected.
The SPEAKERS switches are not set properly.
Speaker connections are not secure.
The protection circuit has been activated
because of short circuit etc.
The SLEEP timer has functioned.
Incorrect setting of the BALANCE control.
Incorrect cord connections.
The + and – wires are connected in reverse at
the amplifier or speakers.
Incorrect cord connections.
No connection from the turntable to the GND
terminal.
The record is being played on a turntable with
an MC cartridge.
The component connected to the REC terminals
of this unit is turned off.
This unit is in the standby mode.
The LOUDNESS control is functioning.
The CD DIRECT AMP switch is ON.
The CD DIRECT AMP switch is ON.
Direct sunlight or lighting (of an inverter type of
fluorescent lamp etc.) is striking the remote
control sensor of the main unit.
The batteries of this remote control transmitter
are too weak.
REMEDY
Firmly plug in the power cord.
Set the switch to either end closely.
Turn this unit into the standby mode and
disconnect the AC power cord from the AC
outlet. After about 30 seconds have passed,
connect the power and operate this unit again.
Connect the cords properly. If the problem
persists, the cords may be defective.
Select an appropriate input source with the
INPUT selector.
Set the SPEAKERS switch which corresponds
to the speakers to be used to the ON position.
Secure the connections.
Turn this unit into the standby mode, and then
turn this unit on to reset the protection circuit.
Cancel the SLEEP timer function.
Adjust it to the appropriate position.
Connect the cords properly. If the problem
persists, the cords may be defective.
Connect the speaker wires in the correct phase
(+ and –).
Firmly connect the audio plugs. If the problem
persists, the cords may be defective.
Make the GND connection between the
turntable and this unit.
The player should be connected to the unit
through the MC head amplifier.
Turn the power to the component on.
Turn the power to this unit on.
Set the LOUDNESS control to the FLAT
position.
Switch off the CD DIRECT AMP switch.
The CD DIRECT AMP switch must be switched
OFF to use those controls.
Change position of the main unit.
Replace the batteries with new ones.
15
English
SPECIFICATIONS
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.04% THD...................60W+60W
6 ohms, 20 Hz to 20 kHz, 0.08% THD...................70W+70W
Maximum Output Power (6 ohms, 1 kHz, 10% THD)
[China and General models only]..................................110W
Dynamic Power per Channel
(by IHF Dynamic Headroom measuring method)
8/6/4/2 ohms.............................................100/120/140/150W
DIN Standard Output Power per Channel
(4 ohms, 1 kHz, 0.7% THD)
[U.K. and Europe models only]........................................95W
IEC Power (8 ohms, 1 kHz, 0.04% THD)
[U.K. and Europe models only]........................................75W
Power Band Width
8 ohms, 30W, 0.1% THD ..............................10 Hz to 50 kHz
Damping Factor
8 ohms, 20 Hz to 20 kHz.....................................100 or more
Input Sensitivity/Impedance
PHONO MM ..............................................2.5 mV/47 k-ohms
CD/TUNER/AUX/MD/TAPE
........................150 mV/47 k-ohms
Maximum Input Signal (1 kHz, 0.04% THD)
PHONO MM .................................................................90 mV
Output Level/Impedance
PHONO MM to REC OUT ..........................150 mV/1 k-ohms
Headphone Jack Rated Output/ Impedance
Output Level (8 ohms, 1 kHz, 0.04% THD)...................0.31V
Impedance..............................................................560 ohms
Frequency Response (20 Hz to 20 kHz)
CD/TUNER/AUX/MD/TAPE
.......................................0±0.5 dB
RIAA Equalization Deviation
PHONO MM.............................................................0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
PHONO MM to REC OUT (1V) ....................................0.02%
CD/TUNER/AUX/MD/TAPE
to SP OUT (30W/8 ohms)
......................................................................................0.02%
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM (5 mV Input Shorted)............................... 82 dB
CD/TUNER/AUX/MD/TAPE
(
Shorted, CD DIRECT AMP: ON)............................... 108 dB
Residual Noise (IHF-A Network)
CD DIRECT AMP: ON.................................................. 35 µV
CD DIRECT AMP: OFF.............................................. 100 µV
Channel Separation
CD/TUNER/AUX/MD/TAPE
(Input 5.1 k-ohms Terminated
1 kHz)............................................................................60 dB
Tone Control Characteristics
BASS:
Boost/cut....................................................±10 dB (20 Hz)
Turnover Frequency................................................350 Hz
TREBLE:
Boost/cut..................................................±10 dB (20 kHz)
Turnover Frequency...............................................3.5 kHz
Continuously variable LOUDNESS Control
(Level related equalization)
Attenuation..................................................... –30 dB (1 kHz)
Power Supply
[U.K. and Europe models].............................AC 230V, 50 Hz
[China and General models]
............................................AC 110/120/220/240V, 60/50 Hz
Power Consumption
[U.K. and Europe models].............................................150W
(In the standby mode: 1.2W)
[China and General models]..........................................150W
(In the standby mode: 1.8W)
AC Outlets
3 SWITCHED OUTLETS
[Europe, China and General models].......100W max. total
1 SWITCHED OUTLET
[U.K. model]..............................................100W max. total
Dimensions (W x H x D) ..........................435 x 151 x 309.3 mm
(17-1/8” x 5-15/16” x 12-3/16”)
Weight.......................................................7.6 kg (16 lbs. 12 oz.)
Accessories.......................................Remote control transmitter
Batteries
Specifications subject to change without notice.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
VZ85100
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Yamaha AX-392 Uživatelský manuál

Yamaha
Značka
Yamaha
Modelka
AX-392
Kategorie
Audio zesilovače
Typ
Uživatelský manuál
Stáhnout PDF
zpráva

v jiných jazycích

Související papíry