Yamaha R-5 Uživatelský manuál
- Kategorie
- Přijímač
- Typ
- Uživatelský manuál
Tato příručka je také vhodná pro
OWNER’S MANUAL
Natural Sound AV Receiver
R-V902
Thank you for selecting this YAMAHA AV receiver.
A
2
After unpacking, check that the following parts are included.
Supplied Accessories ......................................2
Features ..........................................................3
Caution ............................................................4
Profile of This Unit ...........................................5
Speaker Setup ................................................6
Connections ....................................................7
Controls and Their Functions ........................14
Speaker Balance Adjustment ........................17
Basic Operations ...........................................20
Tuning Operations .........................................23
Preset Tuning ................................................24
Using Digital Sound Field Processor (DSP)
......................................................................27
Setting the SLEEP Timer ..............................31
Remote Control Transmitter ..........................32
Notes about the Remote Control Transmitter
......................................................................42
Troubleshooting .............................................43
Specifications ................................................44
Indoor FM Antenna
AM Loop Antenna
Antenna adapter (U.S.A. and Canada models only)
Batteries (size AA, R6, UM-3)
Remote Control Transmitter
User function stickers
CONTENTS
SUPPLIED ACCESSORIES
3
●
5 Speaker Configuration
Main: 90W + 90W (8Ω) RMS Output
Power, 0.07% THD, 1 kHz
Center: 90W (8Ω) RMS Output
Power, 0.07% THD, 1 kHz
Rear: 35W + 35W (8Ω) RMS Output
Power, 0.3% THD, 1 kHz
●
Digital Sound Field Processor
●
Dolby Pro Logic Surround Decoder
●
Theater-like Sound Experience by the
Combination of Dolby Pro Logic and
YAMAHA DSP Technology (CINEMA DSP)
●
Automatic Input Balance Control for
Dolby Pro Logic Surround
●
Test Tone Generator for Easier Speaker
Balance Adjustment
●
3 Center Channel Modes
(NORMAL/WIDE/PHANTOM)
● BASS EXTENSION Switch for Reinforcing
Bass Response
● 40-Station Random Access Preset Tuning
● Automatic Preset Tuning
● Preset Station Shifting Capability (Preset
Editing)
● IF Count Direct PLL Synthesizer Tuning
System
● Video Signal Input/Output Capability
● 6-Channel Discrete Input Terminals for
Connecting with a Dolby Digital (AC-3)
Decoder
● SLEEP Timer
●
“Learning” Remote Control Transmitter
FEATURES
4
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the cabinet assure proper ventilation of
the unit. If these openings are obstructed, the temperature
inside the cabinet will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in well-
ventilated condition. Make sure to allow a space of at least
10 cm behind, 20 cm on the both sides and 30 cm above
the top panel of the unit. Otherwise it may not only damage
the unit, but also cause fire.
6. Always set the VOLUME control to “–
∞
” before starting
the audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
7. Do not attempt to clean the unit with chemical solvents;
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
9. When not planning to use this unit for long periods of time
(ie., vacation, etc.), disconnect the AC power plug from the
wall outlet.
10.To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
11.Grounding or polarization – Precautions should be taken
so that the grounding or polarization of an appliance is not
defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than the
outlet is rated to provide.
13.Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must
be set for your local main voltage BEFORE plugging
into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off.
In this state, this unit is designed to consume a very small
quantity of power.
IMPORTANT
Please record the serial number of this unit in the space
below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
FOR CANADIAN CUSTOMERS
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT AND FULLY INSERT.
THIS CLASS B DIGITAL APPARATUS MEETS ALL
REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch (located
at the rear) according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of
this unit from the AC outlet.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE POWER
SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
MAIN CENTER
MAINS
IMPEDANCE SELECTOR
SWITCHED
I20V 60Hz
I00W MAX. TOTAL
AC OUTLETS
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 6
Ω
MIN. /SPEAKER
A OR B
:4
Ω
MIN. /SPEAKER
A B
:8
Ω
MIN. /SPEAKER
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 8
Ω
MIN. /SPEAKER
A OR B
:8
Ω
MIN. /SPEAKER
A B
:I6
Ω
MIN. /SPEAKER
IMPEDANCE SELECTOR
(U.S.A. model)
5
PROFILE OF THIS UNIT
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field
Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to
bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system,
and this unit will sonically transform your room into a wide range of listening environments –movie theater, concert hall, and so on.
In addition, you get incredible realism from sources encoded with Dolby Surround using the built-in Dolby Pro Logic Surround
Decoder.
Please read this operation manual carefully and store it in a safe place for later reference.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but chances are you’ll still
notice something missing: the acoustic environment of the live
concert hall. Extensive research into the exact nature of the
sonic reflections that create the ambience of a large hall has
made it possible for Yamaha engineers to bring you this same
sound in your own listening room, so you’ll feel all the sound of
a live concert.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of venues such as an actual concert
hall, theater, etc. to allow you to accurately recreate one of
several actual live performance environments, all in your own
home.
Dolby Pro Logic Surround
This unit employs a Dolby Pro Logic Surround decoder similar
to professional Dolby Stereo decoders used in many movie
theaters. By using the Dolby Pro Logic Surround decoder, you
can experience the dramatic realism and impact of Dolby
Surround movie theater sound in your own home. Dolby Pro
Logic employs a four channel five speaker system. The Pro
Logic Surround system divides the input signal into four levels:
the left and right main channels, the center channel (used for
dialog), and the rear surround sound channels (used for sound
effects, background noise, and other ambient noises). The
center channel allows listeners seated in even less-than-ideal
positions to hear the dialog originating from the action on the
screen while experiencing good stereo imaging.
Dolby Surround is encoded on the sound track of pre-recorded
video tapes, laser discs, and some TV/cable broadcasts. When
you play a source encoded with Dolby Surround on this unit,
the Dolby Pro Logic Surround decoder decodes the signal and
distributes the surround-sound effects.
This Dolby Pro Logic Surround Decoder employs a digital
signal processing system. This system improves the stability of
sound at each channel and minimizes crosstalk between
channels, so that positioning of sounds around the room is
more accurate compared with conventional analog signal
processing systems.
In addition, this unit features a built-in automatic input balance
control. This always assures you the best performance without
manual adjustment.
Manufactured under license from Dolby Laboratories Licensing
Corporation. “Dolby”, “AC-3”, “Pro Logic”, and the double-D
symbol are trademarks of Dolby Laboratories Licensing
Corporation.
Dolby Pro Logic Surround + DSP
CINEMA DSP
Dolby Surround sound system shows its full ability in a large
movie theater, because movie sounds are originally designed
to be reproduced in a large movie theater using many
speakers. It is difficult to create a sound environment similar to
that of a movie theater in your listening room, because the
room size, materials of inside walls, the number of speakers,
etc. of your listening room is much different from those of a
movie theater.
Yamaha DSP technology made it possible to present you with
nearly the same sound experience as that of a large movie
theater in your listening room by compensating for lack of
presence and dynamics in your listening room with its original
digital sound fields combined with Dolby Surround sound field.
The combination of Dolby Pro Logic Surround and DSP is used
on the sound field program “ PRO LOGIC ENHANCED”.
The YAMAHA “CINEMA DSP” logo indicates these programs are
created by the combination of Dolby Pro Logic and YAMAHA
DSP technology.
6
SPEAKER SETUP
SPEAKERS TO BE USED
This unit is designed to provide the best sound-field quality with a 5 speaker configuration. The most effective speakers to use with
this unit are main speakers, rear speakers and a center speaker. You may omit the center speaker. (Refer to the “4-Speaker
Configuration” shown below.)
The main speakers are used for the main source sound plus the effect sounds. They will probably be the speakers from your
present stereo system. The rear speakers are used for the effect and surround sounds, and the center speaker is for the center
sounds (dialog etc.) within programs encoded with Dolby Surround. The center speaker needs to be equal in power to the main
speakers, although the rear speakers should not be equal. However, all the speakers should have high enough power handling to
accept the maximum output of this unit.
SPEAKER PLACEMENT
The recommended speaker configuration, the 5-speaker configuration, will require two speaker pairs: main speakers (your normal
stereo speakers), and rear speakers, plus a center speaker. When you place these speakers, refer to the following.
Main: In normal position. (The position of your present
stereo speaker system.)
Rear: Behind your listening position, facing slightly inward.
Nearly six feet (approx. 1.8 m) up from the floor.
Center: Precisely between the main speakers. (To avoid
interference with TV sets, use a magnetically shielded
speaker.)
Front L Center Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L
Rear R
Front L Front R
Dialogue
Surround sound
Dialogue
Surround sound
Rear L Rear R
Front R
Center
Front L
TV set
Rear R
Rear L
Main L
Main R
Main L
Main R
Main L
Main R
SPEAKER CONFIGURATION
5-Speaker Configuration
This configuration is the most effective and recommended one.
In this configuration, the center speaker is necessary as well as
the rear speakers. If the program DOLBY PRO LOGIC or
DOLBY PRO LOGIC ENHANCED is selected, conversations
will be output from the center speaker and the ambience will be
excellent.
• Set the center channel mode to the “NORMAL” or “WIDE”
position. (For details, refer to page 18.)
4-Speaker Configuration
The center speaker is not used in this configuration. If the
program DOLBY PRO LOGIC or DOLBY PRO LOGIC
ENHANCED is selected, the center sound is output from the
left and the right main speakers. However, the sound effect of
other programs can be the same as that of the 5-speaker
configuration.
• Be sure to set the center channel mode to the “PHANTOM”
position. (For details, refer to page 18.)
7
CONNECTIONS
Never plug in this unit and other components until all connections are completed.
CONNECTIONS WITH OTHER COMPONENTS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
* If you have YAMAHA components numbered as 1, 2, 3, etc. on the rear panel, connections can be made easily by making sure
to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.
*
1
,
*
2
: See the next page.
FM
ANT
AM
ANT
GND
75Ω UNBAL.
GND
MONITOR
OUT
DVD/LD
TV/DBS
VIDEO
IN OUT
VCR
VIDEO SIGNAL
PHONO CD
TAPE ( MD ) DVD/LD
TV/DBS
VCR
TAPE
PB
REC
OUT
IN OUT
AUDIO SIGNAL
1 3 4
MAIN CENTER REAR
(SURROUND)
OUTPUT
SUB
WOOFER
6CH DISCRETE INPUT
DVD/LD TV/DBS
SURROUND
CENTERMAIN
REAR
(SURROUND)
CENTER
CD
DUAL
SINGLE
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
MAIN
SPEAKERS
A
B
A
B
SUB
WOOFER
MAINS
IMPEDANCE SELECTOR
SWITCHED
I20V 60Hz
I00W MAX. TOTAL
AC OUTLETS
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 6
Ω
MIN. /SPEAKER
A OR B
:4
Ω
MIN. /SPEAKER
A B
:8
Ω
MIN. /SPEAKER
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 8
Ω
MIN. /SPEAKER
A OR B
:8
Ω
MIN. /SPEAKER
A B
:I6
Ω
MIN. /SPEAKER
GND
OUTPUT
OUTPUT
LINE OUT
LINE IN
VIDEO OUT
AUDIO OUT
AUDIO OUT
AUDIO IN
VIDEO IN
VIDEO OUT
VIDEO IN
AUDIO OUT
VIDEO OUT
(U.S.A. model)
To AC outlet
Turntable LD player etc.
Video cassette recorder
TV/Satellite tuner
Tape deck,
MD recorder, etc.
CD player
Monitor TV
*
2
*
1
8
AC OUTLET(S) (SWITCHED)
[U.S.A., Canada and General models]
........................................................ 2 SWITCHED OUTLETS
[Australia model]................................ 1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of components)
that can be connected to the SWITCHED AC OUTLET(S) is
100 watts.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to the GND
terminal will normally minimize hum, but in some cases better
results may be obtained with the ground wire disconnected.
CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL)
These terminals are used to connect any video input source such as a camcorder to this unit.
Camcorder
L
R
VIDEO
VIDEO AUX
VIDEO L AUDIO R
VIDEO OUT
AUDIO OUT L
AUDIO OUT R
*
1
*
2
9
Connecting with a Dolby Digital (AC-3) Decoder
If you have a Dolby Digital (AC-3) Decoder unit or an LD player etc. which incorporates a Dolby Digital (AC-3) Decoder, its discrete
outputs can be connected to this unit.
Notes
• The laserdisc player (or another unit) must be also
connected to the DVD/LD (or TV/DBS) AUDIO SIGNAL input
terminals of this unit for playing a source with the Dolby Pro
Logic Surround decoded or in normal stereo (or monaural).
• The discrete signals input to this unit cannot be recorded by
a tape deck, MD recorder or VCR. To record a source played
on the laserdisc player (or another unit), it must be
connected to the DVD/LD (or TV/DBS) AUDIO/VIDEO
SIGNAL input terminals of this unit.
• If you made no connection to the SUBWOOFER input
terminal of this unit or you will not use a subwoofer, you
should make a setting for distributing signals at the LFE
channel to the right and left MAIN output terminals on the
Dolby Digital (AC-3) Decoder unit.
For details, refer to the owner’s manual for the Dolby Digital
(AC-3) Decoder unit.
FM
ANT
AM
ANT
GND
75Ω UNBAL.
GND
MONITOR
OUT
DVD/LD
TV/DBS
VIDEO
IN OUT
VCR
VIDEO SIGNAL
PHONO CD
TAPE ( MD ) DVD/LD
TV/DBS
VCR
TAPE
PB
REC
OUT
IN OUT
AUDIO SIGNAL
1 3 4
6CH DISCRETE INPUT
DVD/LD TV/DBS
SURROUND
CENTERMAIN
SUB
WOOFER
MONITOR
OUT
S VIDEO
IN OUT
VCR
AC-3 RF
OUT
AC-3 RF
IN
DIGITAL
IN
DIGITAL
OUT
VIDEO OUT
AUDIO OUT
6CH DISCRETE OUTPUT
CENTER SURROUNDMAIN
SUB
WOOFER
Dolby Digital (AC-3) Decoder unit
RF Demodulator
Laserdisc player with AC-3 RF output or
another unit with AC-3 RF output
(U.S.A. model)
10
CONNECTING SPEAKERS
MAIN CENTER REAR
(SURROUND)
OUTPUT
SUB
WOOFER
REAR
(SURROUND)
CENTER
CD
DUAL
SINGLE
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
MAIN
SPEAKERS
A
B
A
B
IMPEDANCE SELECTOR
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 6
Ω
MIN. /SPEAKER
A OR B
:4
Ω
MIN. /SPEAKER
A B
:8
Ω
MIN. /SPEAKER
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 8
Ω
MIN. /SPEAKER
A OR B
:8
Ω
MIN. /SPEAKER
A B
:I6
Ω
MIN. /SPEAKER
Rear speaker Rear speaker
Center speaker
Main speakers B
Left
Right
Left
Right
Main speakers A
Subwoofer system
Left
Right
Note
Use speakers with the specified impedance shown on the rear
of this unit.
Note on main speaker connections:
One or two speaker systems can be connected to this unit. If
you use only one speaker system, connect it to either the
SPEAKERS A or B terminals.
Note on a subwoofer connection:
You may wish to add a subwoofer to reinforce low frequencies
or to output low bass sound from the subwoofer channel when
reproducing discrete signals.
Connect the SUBWOOFER OUTPUT terminal of this unit to
the INPUT terminal of the subwoofer amplifier, and connect the
speaker terminals of the subwoofer amplifier to the subwoofer.
With some subwoofers, including the Yamaha Active Servo
Processing Subwoofer System, the amplifier and subwoofer
are in the same unit.
Note on center speaker connection:
One or two center speakers can be connected to this unit. If
you cannot place the center speaker on or under the TV, it is
recommended to use two center speakers and place them on
both sides of the TV to orient the center sound at the center
position. For connecting two center speakers, follow the
method shown below.
REAR
(SURROUND)
CENTER
CD
DUAL
SINGLE
Center speaker
Center speaker
(U.S.A. model)
11
For connecting to the MAIN SPEAKERS terminals
Red: positive (+)
Black: negative (–)
➀
Unscrew the knob.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Tighten the knob and
secure the wire.
Banana Plug connections are also possible. Simply insert the
Banana Plug connector into the corresponding terminal.
For connecting to the REAR and CENTER SPEAKERS
terminals
Red: positive (+)
Black: negative (–)
➀
Press the tab.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Release the tab and
secure the wire.
➁
➂
➀
1
2
3
How to Connect:
Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are
faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –
markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.
Caution
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could damage
this unit and/or speakers.
12
MAIN OUTPUT terminals
These terminals are for main channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive main speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
* Output signals from the MAIN OUTPUT terminals only are
affected by the use of BASS, TREBLE, BALANCE controls
and BASS EXTENSION switch.
CENTER OUTPUT terminal
This terminal is for center channel line output. There is no
connection to this terminal when you use the built-in amplifier.
However, if you drive a center speaker with an external power
amplifier, connect the input terminal of the external amplifier to
this terminal.
REAR (SURROUND) OUTPUT terminals
These terminals are for rear channel line output. There is no
connection to these terminals when you use the built-in
amplifier.
However, if you drive rear speakers with an external stereo
power amplifier, connect the input terminals of the external
amplifier (MAIN IN or AUX terminals of a power amplifier or an
integrated amplifier) to these terminals.
SUBWOOFER OUTPUT terminal
This terminal is for connecting with the input terminal of an
amplifier for driving a subwoofer.
When the input signals to this unit are in normal 2-channel
stereo, this terminal outputs only frequencies below 200 Hz
from the main and center channels. When discrete signals are
input to this unit and are selected as the input source, this
terminal outputs signals from the subwoofer channel.
Note
Output level of signals from all of these terminals are
adjusted by the use of VOLUME control on the front panel
or MASTER VOLUME keys on the remote control
transmitter.
OUTPUT terminals (for driving speakers with external amplifiers)
Be sure to switch this only when the power of this unit is turned
off.
Select the position whose requirements your speaker system
meets.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
IF THIS UNIT FAILS TO TURN ON WHEN THE POWER
SWITCH IS PRESSED
The IMPEDANCE SELECTOR switch may not be set to
either end closely. If so, set the switch to either end closely.
(Upper position)
Rear: The impedance of each speaker must be 6Ω or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 6Ω or higher.
If you use two center speakers, the impedance of
each speaker must be 3Ω or higher.
Main: If you use one pair of main speakers, the impedance
of each speaker must be 4Ω or higher.
If you use two pairs of main speakers, the impedance
of each speaker must be 8Ω or higher.
(Lower position)
Rear: The impedance of each speaker must be 8Ω or
higher.
Center: If you use one center speaker, the impedance of the
speaker must be 8Ω or higher.
If you use two center speakers, the impedance of
each speaker must be 4Ω or higher.
Main: If you use one pair of main speakers, the impedance
of each speaker must be 8Ω or higher.
<Except Canada model>
If you use two pairs of main speakers, the impedance
of each speaker must be 16Ω or higher.
IMPEDANCE SELECTOR switch
IMPEDANCE SELECTOR
SINGLE
:
6
Ω
MIN. /SPEAKER
DUAL
:3
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 6
Ω
MIN. /SPEAKER
A OR B
:4
Ω
MIN. /SPEAKER
A B
:8
Ω
MIN. /SPEAKER
SINGLE
:
8
Ω
MIN. /SPEAKER
DUAL
:4
Ω
MIN. /SPEAKER
CENTER
MAIN
REAR 8
Ω
MIN. /SPEAKER
A OR B
:8
Ω
MIN. /SPEAKER
A B
:I6
Ω
MIN. /SPEAKER
MAIN CENTER REAR
(SURROUND)
OUTPUT
SUB
WOOFER
(U.S.A. model)
13
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminals correctly, referring to the following diagram.
●
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
●
When connecting the indoor
FM antenna, insert its
connector into the FM ANT
terminal firmly.
●
If you need an outdoor
FM antenna to improve
FM reception quality, either
300-ohm feeder or coaxial cable may be used. In locations
troubled by electrical interference, coaxial cable is
preferable.
FM
ANT
AM
ANT
GND
75Ω UNBAL.
GND
PHONO
➀
➁
➂
Orient so that the best
reception is obtained.
1 2 3
Outdoor FM antenna
Outdoor AM antenna
AM loop
antenna
(included)
Ground
75-ohm/300-ohm
antenna adapter
75-ohm/300-ohm
antenna adapter
75-ohm coaxial cable
300-ohm feeder
Indoor FM
antenna
(included)
1 POWER switch
Press this switch to switch the power on. Press it again to
switch the power off.
2 Standby mode indicator
(Except U.S.A. and Canada models)
While the power is on, pressing the SYSTEM POWER OFF
key on the remote control transmitter switches the unit to the
standby mode. In this mode, this indicator is illuminated.
3 Remote control sensor
Receives signals from the remote control transmitter.
4 Display panel
Shows various information. (Refer to page 16 for details.)
5 Input selector buttons
Select a program source to listen to or watch. When a button is
pressed, the name of selected source appears on the display.
6 DSP program selector buttons
Select a DSP program. When a button is pressed, the name of
selected program lights up on the display.
7 2CH/6CH selector button
When the TV/DBS or DVD/LD input source is selected,
pressing this button switches the input signals between 2
channel stereo signals and 6 channel discrete signals. When
switched to “6CH”, discrete signals from the unit connected to
the 6CH DISCRETE INPUT DVD/LD TV/DBS terminals of this
unit are selected as the input signals.
8 EFFECT button
Switches on/off the digital sound field processor (including the
Dolby Pro Logic Surround decoder).
9 VOLUME control
Used to raise or lower the volume level.
0 PHONES jack
When you listen with headphones, connect the headphones to
the PHONES jack. You can listen to the sound to be output
from the main speakers through headphones.
When listening with headphones privately, set both the
SPEAKERS A and B switches to the OFF position and switch
off the digital sound field processor (so that no DSP program
name is illuminated on the display) by pressing the EFFECT
button.
14
PHONES
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
NATURAL SOUND AV RECEIVER
R–V902
CINEMA DSP
A
ON
OFF
ON
OFF
B
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
POWER
SPEAKERSPHONES
BASS TREBLE BALANCE
VIDEO AUX
VIDEO L AUDIO R
VOLUME
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
BASS
EXTENSION
55
4
3
2
l
0
l
2
3
4
DELAY/CENTER
/REAR/SWFR
FM
/
AM
MAN'L
/
AUTO FM
TUNING
MODE
AUTO
/
MAN'L MONO
CENTER
MODE
DISCO
CONCERT
HALL
ROCK
CONCERT
EFFECT
DOWN
TUNING
UP
MEMORY
EDIT
TIME
/
LEVEL
PRESET
kHz
MHz
MEMORY
AUTO PTY HOLD
SLEEP
TAPE MONITOR
STEREO
ms dB
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
DISCO
ROCK CONCERT
CONCERT HALL
A
/
B
/
C
/
D
/
E
1
2 3 4 5 6 7 8
VCR DVD
/
LDTV
/
DBS
VIDEO AUX
TUNER
CD
PHONO
NORMAL
WIDE
PHANTOM
EFFECT OFF
PS
EON
INFO AFFAIRS SPORT
NEWS
RT CTPTY
0
20
l00
40 60
1
0A BC D E F G HI
J
LMKN
23 4 5 6 789
TAPE (MD) MON 2CH/6CH
A SPEAKERS switches
Set the switch A or B (or both A and B) for the main speaker
system (connected to this unit) you will use to the ON position.
Set the switch for the main speaker system you will not use to
the OFF position.
B A/B/C/D/E button
Press this button to select a desired group (A–E) of preset
stations.
C BASS EXTENSION switch
When this switch is pressed inward (ON), boosts bass
frequency response at the main left and main right channels
while maintaining overall tonal balance. If you do not have a
subwoofer, the use of this switch will be effective to reinforce
the bass frequencies.
D Preset station number selector buttons
Select a preset station number (1 to 8).
E Tone controls
These controls are effective only for the sound from the main
speakers.
BASS
Used to increase or decrease the low frequency response.
The 0 position produces flat response.
TREBLE
Used to increase or decrease the high frequency response.
The 0 position produces flat response.
F BALANCE control
Adjusts the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused by
speaker location or listening room conditions.
G FM/AM buttons
Press this button to switch the reception band to FM or AM.
H MEMORY (MAN’L/AUTO FM) button
When this button is pressed, the MEMORY indicator flashes for
about 5 seconds. During this period, select a desired preset
station number by pressing the corresponding preset station
number selector button to enter the displayed station into the
memory.
When this button is pressed and held for about 3 seconds, the
automatic preset tuning begins. (Refer to page 25 for details.)
I EDIT button
This button is used to exchange the places of two preset
stations with each other.
J TUNING DOWN/UP button
Used for tuning. Press the “UP” side to tune in to higher
frequencies, and press the “DOWN” side to tune in to lower
frequencies.
K TUNING MODE (AUTO/MAN’L MONO) button
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this button
so that “AUTO” lights up on the display. To select the manual
tuning mode, press this button so that “AUTO” goes off.
L DELAY/CENTER/REAR/SWFR and TIME/LEVEL +/–
buttons
Adjust the delay time (DELAY), the rear channel output level
(REAR), center channel output level (CENTER) and the output
level to the SUBWOOFER OUTPUT terminal (SWFR).
Select the item which you want to adjust by pressing the
DELAY/CENTER/REAR/SWFR button and adjust its time or
level by pressing the TIME/LEVEL +/– button.
M CENTER MODE button
Selects a center channel output mode (NORMAL, WIDE or
PHANTOM). (For details, refer to page 18.)
N VIDEO AUX terminals
Connect an auxiliary video or audio input source unit such as a
camcorder to these terminals. The source connected to these
terminals can be selected by the corresponding input selector
button.
15
1 Multi-information display
Displays various information, for example station frequency,
preset station number and name of selected input source.
2 STEREO indicator
Lights up when an FM stereo broadcast with sufficient signal
strength is received.
3 Signal-level meter
Indicates the signal level of the received station.
If multipath interference is detected, the indication decreases.
4 SLEEP indicator
Lights up while the built-in SLEEP timer is functioning.
5 Center channel mode indicators
The name of a selected center channel mode lights up only
when a program which uses the Dolby Pro Logic Surround
decoder is selected.
6 EFFECT OFF indicator
Lights up if neither the digital sound field processor nor the
Dolby Pro Logic Surround decoder is on. In this state, sound
output is 2-channel stereo.
7 MEMORY indicator
When the MEMORY button is pressed, this indicator flashes
for about 5 seconds. During this period, the displayed station
can be programmed to the memory by using the A/B/C/D/E
button and the preset station number selector buttons.
8 AUTO indicator
Lights up when this unit is in the automatic tuning mode.
9 TAPE MONITOR indicator
Lights up when the tape deck (or MD recorder etc.) is selected
as the input source by pressing the TAPE (MD) MON button.
0 DSP program indicators
The name of a selected DSP program lights up when the built-
in digital sound field processor and/or the Dolby Pro Logic
Surround decoder is on.
16
DISPLAY PANEL
PRESET
kHz
MHz
MEMORY
AUTO
SLEEP
TAPE MONITOR
STEREO
ms dB
PRO LOGIC
ENHANCED
CONCERT
VIDEO
MONO
MOVIE
STADIUM
DISCO
ROCK CONCERT
CONCERT HALL
NORMAL
WIDE
PHANTOM
EFFECT OFF
0
20
l00
40 60
123456
879 0
1
Set to the “
∞
” position.
2 Turn the power on.
3 Select the main speakers to be used.
* If you use two main speaker systems, press both the A
and B switches.
4
Set to the “0” position.
5
Set to the “OFF ( )”.
6
17
SPEAKER BALANCE ADJUSTMENT
This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test
tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from
each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround
decoder.
The adjustment of each speaker output level should be done at your listening position with the remote control transmitter.
Otherwise, the result may not be satisfactory.
SPEAKERS
A
ON
OFF
B
BASS TREBLE
55
4
3
2
l
0
l
2
3
4
55
4
3
2
l
0
l
2
3
4
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
POWER
BA
B
VCR
DVD/LD
V-AUX
PHONO
EFFECT
ON/OFF
TV/DBS
C
DIR
DISCSTOP
PRESET
A/B/C/D/E
PRO LOGIC ENHANCED
123
456
789
MOVIE
STADIUM
DISCO
MONO
VIDEO
CONCERT
ROCK HALL
TIME/LEVEL
DELAY
CENTER
REAR
SWFR
TEST
S EEP 2CH/6CH
0
+10
1
2
3
l6
20
28
40
60
l2
8
4
2
0
–dB
BASS
EXTENSION
ON
OFF
5 4
6
TEST
CONTINUED
18
l6
20
28
40
60
l2
8
4
2
0
–dB
7 Select the center channel output mode suitable for your
speaker configuration.
(Refer to “SPEAKER CONFIGURATION” on page 6.)
On the feature of each mode, refer to the “Note” shown
below.
Note
In step 7, when you select a center channel output mode, note
the following.
For 5 speaker configuration)
NORMAL: Select this mode when you use a center speaker
that is smaller than the main speakers. In this
mode, the bass tone will be output from the main
speakers.
WIDE: Select this mode when you use the center speaker
approximately same sized as the main speakers.
For 4 speaker configuration)
PHANTOM: Select this mode when you do not use the center
speaker. The center sound will be output from the
left and right main speakers.
8 Turn up the volume.
You will hear a test tone (like pink noise) from the left main
speaker, then the center speaker, then the right main
speaker, and then the rear speakers, for about two seconds
each. The display changes as shown below.
* The test tone from the left rear speaker and the right
rear speaker will be heard at the same time.
9 Adjust the BALANCE control so that the effect sound
output level of the left main speaker and the right main
speaker are the same.
CENTER
MODE
NORMAL
WIDE
PHANTOM
7
9
BALANCE
55
4
3
2
l
0
l
2
3
4
LR
TIME/LEVEL
DELAY
CENTER
REAR
SWFR
TEST
SLEEP 2CH/6CH
MASTER VOLUME
TV
VCR
OFF
SYSTEM
POWER
0
+10
REMOTE CONTROL
TRANSMITTER
8
Main (L)
Main (R)
Center
Rear (L and R)
19
10 Adjust the sound output levels of the center
speaker and the rear speakers so that they
become almost as same as that of the main
speakers.
a) Press once or more so that “CENTER” or “REAR”
appears on the display.
* Select “CENTER” to adjust the output level of the
center speaker, and select “REAR” to adjust the
output level of the rear speakers.
b) Adjust its level.
* Pressing the + side raises and the – side lowers the
level.
11 Cancel the test tone.
Notes
●
Once you have completed these adjustments, you can
adjust whole sound level on your audio system by using
the VOLUME control (or the MASTER VOLUME keys on
the remote control transmitter) only.
●
If you use external power amplifiers, you may also use
their volume controls to achieve proper balance.
●
In step 10, if the center channel mode is in the
“PHANTOM” position, the sound output level of the center
speaker cannot be adjusted. This is because in this
mode, the center sound is automatically output from the
left and right main speakers.
V-AUX
PHONO
EFFECT
ON/OFF
PRO LOGIC ENHANCED
123
456
789
MOVIE
STADIUM
DISCO
MONO
VIDEO
CONCERT
ROCK HALL
TIME/LEVEL
DELAY
CENTER
REAR
SWFR
TEST
SLEEP 2CH/6CH
MASTER VOLUME
TV
VCR
OFF
SYSTEM
POWER
0
+10
Disappears.
TEST
11
10
1
Set to the “
∞
” position.
2 Turn the power on.
3 Select the desired input source by using the input
selector buttons.
(For video sources, turn the TV/monitor ON.)
* The name of the selected input source will appear on
the display.
4 Select the main speakers to be used.
* If you use two main speaker systems, press both the A
and B switches.
5 Play the source. (For detailed information on the
tuning operation, refer to page 23.)
6
Adjust to the desired output level.
7 If desired, adjust the BASS, TREBLE, BALANCE
controls, etc. (refer to page 22.) and use the digital
sound field processor. (Refer to page 28.)
Notes on using the input selector buttons
●
Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
* To select the source connected to the VIDEO AUX
terminals on the front panel, press VIDEO AUX.
●
The selection of TAPE (MD) MON cannot be canceled by
pressing another input selector button. To cancel it, press
TAPE (MD) MON again so that “TAPE MONITOR”
disappears from the display.
When you select a button other than TAPE (MD) MON,
make sure that “TAPE MONITOR” is not illuminated on the
display.
●
If you select the input selector button for a video source
without canceling the selection of TAPE (MD) MON, the
playback result will be the video image from the video
source and the sound from the audio tape (or MD etc.).
●
Once you play a video source, its video image will not be
interrupted even if the input selector button for an audio
source is selected.
To turn off the power
Press the POWER switch again.
20
BASIC OPERATIONS
TO PLAY A SOURCE
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
SPEAKERS
A
ON
OFF
B
l6
20
28
40
60
l2
8
4
2
0
–dB
VOLUME
VCR DVD
/
LDTV
/
DBS
VIDEO AUX
TAPE (MD) MON 2CH/6CH
POWER
1, 6
2
4
7
l6
20
28
40
60
l2
8
4
2
0
–dB
3
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Yamaha R-5 Uživatelský manuál
- Kategorie
- Přijímač
- Typ
- Uživatelský manuál
- Tato příručka je také vhodná pro
v jiných jazycích
- polski: Yamaha R-5 Instrukcja obsługi
- español: Yamaha R-5 Manual de usuario
- italiano: Yamaha R-5 Manuale utente
- Deutsch: Yamaha R-5 Benutzerhandbuch
- svenska: Yamaha R-5 Användarmanual
- português: Yamaha R-5 Manual do usuário
- français: Yamaha R-5 Manuel utilisateur
- Türkçe: Yamaha R-5 Kullanım kılavuzu
- English: Yamaha R-5 User manual
- dansk: Yamaha R-5 Brugermanual
- русский: Yamaha R-5 Руководство пользователя
- suomi: Yamaha R-5 Ohjekirja
- Nederlands: Yamaha R-5 Handleiding
- română: Yamaha R-5 Manual de utilizare
Související papíry
-
Yamaha RX-V592RDS Uživatelský manuál
-
-
-
-
-
-
-
-
-