Yamaha GO44 Uživatelský manuál

Značka: Yamaha

Modelka: GO44

Kategorie: Hudební nástroje

Typ: Uživatelský manuál

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

Yamaha Web Site (English Only)

http://www.yamahasynth.com

Yamaha Manual Library

http://www.yamaha.co.jp/manual/

Owner‘s Manual

This product utilizes batteries or an external power

supply (adapter). DO NOT connect this product to

any power supply or adapter other than one

described in the manual, on the name plate, or

speciﬁcally recommended by Yamaha.

WARNING: Do not place this product in a position

where anyone could walk on, trip over ,or roll any-

thing over power or connecting cords of any kind.

The use of an extension cord is not recommended!

If you must use an extension cord, the minimum

wire size for a 25’ cord (or less ) is 18 AWG. NOTE:

The smaller the AWG number ,the larger the cur-

rent handling capacity. For longer extension cords,

consult a local electrician.

This product should be used only with the compo-

nents supplied or; a cart, rack, or stand that is rec-

ommended by Yamaha. If a cart, etc., is used,

please observe all safety markings and instructions

that accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is

believed to be correct at the time of printing. How-

ever, Yamaha reserves the right to change or mod-

ify any of the speciﬁcations without notice or

obligation to update existing units.

This product, either alone or in combination with an

ampliﬁer and headphones or speaker/s, may be

capable of producing sound levels that could cause

permanent hearing loss. DO NOT operate for long

periods of time at a high volume level or at a level

that is uncomfortable. If you experience any hear-

ing loss or ringing in the ears, you should consult

an audiologist.

IMPORTANT: The louder the sound, the shorter

the time period before damage occurs.

Some Yamaha products may have benches

and / or accessory mounting ﬁxtures that are

either supplied with the product or as optional

accessories. Some of these items are designed

to be dealer assembled or installed. Please

make sure that benches are stable and any

optional ﬁxtures (where applicable) are well

secured BEFORE using.

Benches supplied by Yamaha are designed for

seating only. No other uses are recommended.

NOTICE:

Service charges incurred due to a lack of knowl-

edge relating to how a function or effect works

(when the unit is operating as designed) are not

covered by the manufacturer’s warranty, and are

therefore the owners responsibility. Please study

this manual carefully and consult your dealer

before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both

user safe and environmentally friendly. We sin-

cerely believe that our products and the production

methods used to produce them, meet these goals.

In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice:

This product MAY contain a small non-recharge-

able battery which (if applicable) is soldered in

place. The average life span of this type of battery

is approximately ﬁve years. When replacement

becomes necessary, contact a qualiﬁed service

representative to perform the replacement.

This product may also use “household” type batter-

ies. Some of these may be rechargeable. Make

sure that the battery being charged is a recharge-

able type and that the charger is intended for the

battery being charged.

When installing batteries, do not mix batteries with

new, or with batteries of a different type. Batteries

MUST be installed correctly. Mismatches or incor-

rect installation may result in overheating and bat-

tery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any

battery. Keep all batteries away from children. Dis-

pose of used batteries promptly and as regulated

by the laws in your area. Note: Check with any

retailer of household type batteries in your area for

battery disposal information.

Disposal Notice:

Should this product become damaged beyond

repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local,

state, and federal regulations that relate to the dis-

posal of products that contain lead, batteries, plas-

tics, etc. If your dealer is unable to assist you,

please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the

product. The model number, serial number, power

requirements, etc., are located on this plate. You

should record the model number, serial number,

and the date of purchase in the spaces provided

below and retain this manual as a permanent

record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

SPECIAL MESSAGE SECTION

92-BP (bottom)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets

FCC requirements. Modiﬁcations not expressly

approved by Yamaha may void your authority,

granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to

accessories and/or another product use only

high quality shielded cables. Cable/s supplied

with this product MUST be used. Follow all

installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use

this product in the USA.

3. NOTE: This product has been tested and found

to comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements

provides a reasonable level of assurance that

your use of this product in a residential environ-

ment will not result in harmful interference with

other electronic devices. This equipment gener-

ates/uses radio frequencies and, if not installed

and used according to the instructions found in

the users manual, may cause interference

harmful to the operation of other electronic

devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in

all installations. If this product is found to be the

source of interference, which can be deter-

mined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one

of the following measures:

Relocate either this product or the device that is

being affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

ﬁlter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is

300 ohm ribbon lead, change the lead-in to co-

axial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local

retailer authorized to distribute this type of prod-

uct. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of

America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those

products distributed by Yamaha Corporation of

America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : MOBILE AUDIO INTERFACE

Model Name : GO44

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

(FCC DoC)

(3)-9

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions

include, but are not limited to, the following:

• Only use the voltage speciﬁed as correct for the instrument.

The required voltage is printed on the name plate of the

instrument.

• Use the speciﬁed adaptor (PA-3C or an equivalent

recommended by Yamaha) only. Using the wrong adaptor can

result in damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

• Do not place the AC adaptor cord near heat sources such as

heaters or radiators, and do not excessively bend or otherwise

damage the cord, place heavy objects on it, or place it in a

position where anyone could walk on, trip over, or roll anything

over it.

• Do not open the instrument or attempt to disassemble the

internal parts or modify them in any way. The instrument

contains no user-serviceable parts. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in

damp or wet conditions, or place containers on it containing

liquids which might spill into any openings.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a ﬁre.

• If the AC adaptor cord or plug becomes frayed or damaged, or

if there is a sudden loss of sound during use of the instrument,

or if any unusual smells or smoke should appear to be caused

by it, immediately disconnect the adaptor plug from the outlet,

and have the instrument inspected by qualiﬁed Yamaha service

personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or

others, or damage to the instrument or other property. These precautions include, but are not limited

to, the following:

• When removing the electric plug from the instrument or an

outlet, always hold the plug itself and not the cord.

• Unplug the AC power adaptor when not using the instrument,

or during electrical storms.

• Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality,

or possibly cause overheating in the outlet.

• Do not expose the instrument to excessive dust or vibrations,

or extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day) to prevent the possibility of

panel disﬁguration or damage to the internal components.

• Do not use the instrument in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices. Otherwise,

the instrument, TV, or radio may generate noise.

• Do not place the instrument in an unstable position where it

might accidentally fall over.

Power supply/AC power adaptor

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/AC power adaptor Location

(3)-9

• Before moving the instrument, remove all connected adaptor

and other cables.

• When setting up the instrument, make sure that the AC outlet you

are using is easily accessible. If some trouble or malfunction

occurs, immediately disconnect the plug from the outlet.

• Before connecting the instrument to other electronic

components, turn off the power for all components. Before

turning the power on or off for all components, set all volume

levels to minimum. Also, be sure to set the volumes of all

components at their minimum levels and gradually raise the

volume controls while playing the instrument to set the desired

listening level.

• When cleaning the instrument, use a soft, dry cloth. Do not use

paint thinners, solvents, cleaning ﬂuids, or chemical-

impregnated wiping cloths.

• Never insert or drop paper, metallic, or other objects into the

gaps on the panel. If this happens, immediately unplug the

power cord from the AC outlet. Then have the instrument

inspected by qualiﬁed Yamaha service personnel.

• Do not place vinyl, plastic or rubber objects on the instrument,

since this might discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the buttons,

switches or connectors.

• Do not use the instrument/device or headphones for a long

period of time at a high or uncomfortable volume level, since

this can cause permanent hearing loss. If you experience any

hearing loss or ringing in the ears, consult a physician.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the instrument, or data that is lost or destroyed.

SPECIAL NOTICES

- This owner’s manual is the exclusive copyright of Yamaha Corporation.

- The supplied Cubase LE, HALion SE, and Groove Agent SE are the exclusive copyrights of Steinberg Media

Technologies GmbH.

- Copying of the supplied software or reproduction of this manual in whole or in part by any means is expressly

forbidden without the written consent of the manufacturer.

-Yamaha makes no representations or warranties with regard to the use of the software and documentation

and cannot be held responsible for the results of the use of this manual and the software.

- The supplied disk is a CD-ROM. Do not attempt to play the disk on an audio CD player. Doing so may result

in irreparable damage to your audio CD player.

- Copying of the commercially available musical data including but not limited to MIDI data and/or audio data

is strictly prohibited except for your personal use.

- The screen displays as illustrated in this owner’s manual are for instructional purposes, and may appear

somewhat different from the screens which appear on your computer.

- Future upgrades of application and system software and any changes in speciﬁcations and functions will be

announced separately.

-Windows is the registered trademarks of Microsoft

Corporation.

- Apple and Macintosh are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

- FireWire and the FireWire symbol are trademarks of Apple Computer, Inc., registered in the U.S. and other

countries. The FireWire logo is a trademark of Apple Computer, Inc.

- Steinberg, Cubase, HALion, and Groove Agent are the registered trademarks of Steinberg Media Technologies

GmbH.

- The company names and product names in this Owner’s Manual are the trademarks or registered trademarks

of their respective companies.

- Speciﬁcations and descriptions in this owner’s manual are for information purposes only.

-Yamaha Corp. reserves the right to change or modify products or speciﬁcations at any time without prior

notice. Since speciﬁcations, equipment or options may not be the same in every locale, please check with

your Yamaha dealer.

Connections

Maintenance

Handling caution

Welcome to the GO44

Thank you for choosing the Yamaha GO44 Mobile Audio Interface.

The GO44 is a portable IEEE1394 (FireWire

) audio/MIDI interface featuring multi-channel

operation and professional-quality audio. Connect the GO44 to a computer equipped with an

IEEE1394 (FireWire) port and enjoy the powerful, versatile features of digital audio recording and

editing.

In order to take full advantage of the many features and capabilities provided by the GO44, we

urge you to read this owner’s manual thoroughly before using your GO44 system, and keep the

manual in a safe, accessible location for future reference.

Table of contents

Package Contents............................................................................................ 7

About the Included Software.......................................................................... 7

Power Supply................................................................................................... 7

Software Installation — Windows users ......................................................... 8

Compatible operating systems....................................................................... 8

Preparing to Install......................................................................................... 8

Installing the driver and the Control Panel ..................................................... 9

Assigning the GO44 as the default system audio device (Windows) ............. 11

Software Installation — Macintosh users ..................................................... 12

Compatible operating systems..................................................................... 12

Installing the Control Panel.......................................................................... 12

Assigning the GO44 as the default system audio device (Mac OS X)............ 12

Connectors and controls............................................................................... 13

Front Panel .................................................................................................. 13

Rear Panel.................................................................................................... 13

I/O cable ..................................................................................................... 14

Drivers ........................................................................................................... 16

Windows drivers .......................................................................................... 16

Mac OS X drivers ......................................................................................... 18

GO44 Control Panel ...................................................................................... 19

MAIN display ............................................................................................... 19

The ASIO control panel (Windows only)....................................................... 21

The SCENES panel ....................................................................................... 21

ABOUT ........................................................................................................ 22

Specifications................................................................................................. 23

System Requirements.................................................................................... 24

Troubleshooting............................................................................................ 25

The GO44 package contains the following

items. Check the contents for missing items.

• GO44 main unit

• AC Power Adaptor (PA-3C)

• I/O cable

• GO44 Owner’s Manual

•2 CD-ROMs

(Windows/Macintosh hybrid CD)

• IEEE1394 (FireWire) cable

(6–pin/6–pin)

• IEEE1394 (FireWire) adaptor

(4–pin/6–pin)

* May not be included depending on your particular

area. Please check with your Yamaha dealer.

The included CD-ROMs contain the following

software (driver).

“TOOLS for GO44/GO46” CD-ROM

• Driver/Control Panel installer (Windows)

• Control Panel installer (Macintosh)

• GO44 Owner’s Manual (PDF)

• VST Instruments (VSTi)

HALion SE (Windows/Macintosh)

Groove Agent SE (Windows/Macintosh)

“Cubase LE” CD-ROM

• Cubase LE (Windows/Macintosh)

• The serial number necessary for installing Cubase LE

(Windows) is printed on a sheet included with the CD-

ROM.

• Please install Cubase LE while connected to the

internet and enter all required items during installa-

tion.

•For Macintosh computers double-click the “Cubase

LE.pkg” icon.

•To install VSTi, double-click the following ﬁle on the

“TOOLS for GO44/GO46” CD-ROM.

Windows: VSTi Set\Setup VSTi Set.exe

Macintosh: VSTi Set\Setup VSTi Set.pkg

The GO44 does not have a power switch. The power is automatically turned on when the AC

power adaptor is connected. The GO44 can also be powered via the 6–pin/6–pin IEEE1394

(FireWire) port, making an AC power adaptor unnecessary. However, not all IEEE1394 (FireWire)

controllers deliver a constant operating voltage — therefore, we recommend using the included

AC power adaptor. The AC power adaptor is also useful whenever you would like to conserve the

battery power of your laptop. The AC power adaptor is required if your computer only features a

4–pin IEEE1394 (FireWire) port.

Package Contents

About the Included Software

NOTE

Power Supply

Please perform the following steps in the given order. Do not connect the GO44 module to the

computer until instructed to do so.

Compatible operating systems

The GO44 can be used only under Windows XP (Home/Professional editions) SP (Service Pack) 1

and SP2. Other Windows versions are not supported. To check your Windows version, right click

the [My Computer] icon and select [Properties] from the context menu. You can also access this

menu item by clicking: [Start] → [Control Panel] → [System]. The Service Pack can be obtained

free of charge from the Microsoft web site (www.microsoft.com).

• Refer to the system requirements printed on the package, or in the PDF manual page 24. You can also

check the latest system requirements on the Internet.

http://www.yamahasynth.com/

• If the [System] icon is not shown in the Control Panel, click “Switch to Classic View” in the upper left of the

window to display all control panels and icons.

Preparing to Install

Select [Start] → [Control Panel] and go to [System] → [Hardware] → [Driver Signing] → [Driver

Signing Options] and check the radio button to the left of “Ignore — Install the software anyway

and don’t ask for my approval” and click [OK].

After completing the installation, make sure to restore the original setting if necessary.

Software Installation — Windows

users

NOTE

Software Installation — Windows users

Installing the driver and the Control Panel

1. Insert the included “TOOLS for GO44/GO46” CD-ROM in the CD-ROM drive of

your computer.

2. Double-click on the CD-ROM drive icon in the My Computer menu. Open

[GO44Driver_] → [GO44 Setup.exe] to start the InstallShield Wizard.

3. Select a language for the setup wizard and click [Next] to continue with the instal-

lation. The welcome message of the InstallShield Wizard appears. Click [Next].

4. If you want to specify a different location, click [Change]. Then click [Next].

Software Installation — Windows users

5. Click [Install] to start the installation.

6. As soon as the message shown below appears, connect the GO44 to your com-

puter’s IEEE1394 (FireWire) port using the included cable, and click [OK]. Win-

dows XP will automatically recognize the device as new hardware and will open

the driver installation dialog.

7. Check the radio button to the left of “Yes, I want to restart my computer now.”

and click [Finish] to restart the computer and complete the installation.

Software Installation — Windows users

8. Once the driver installation is complete, the GO44 should appear as the following

entry in the Device Manager. The Device Manager can be found on the Control

Panel under [System]

→ [Hardware]. Then click the [Device Manager] button.

Assigning the GO44 as the default system audio

device (Windows)

If you would like to use the GO44 not only for specific audio applications, but as your default

Windows audio device, go to the Control Panel, select [Sounds and Audio Devices] → [Audio]

and specify the GO44 audio driver as the default device for the desired functions. Since the

GO44 is a professional audio interface, the levels can only be adjusted using the included GO44

Control Panel. The Windows mixer is disabled to prevent it from adversely affecting the signal

quality.

Compatible operating systems

The GO44 can only be used under Mac OS 10.3.4 (OS X) or higher.

Refer to the system requirements printed on the package, or in the PDF manual page 24. You can

also check the latest system requirements on the Internet.

http://www.yamahasynth.com/

Installing the Control Panel

The GO44 uses the operating system’s CoreAudio and CoreMIDI drivers. Therefore, it is not

necessary to install a device-specific driver. Simply plug the device into your IEEE1394 (FireWire)

port using the included cable and the GO44 can be used immediately. However, to take full

advantage of the advanced routing, sample rate switching, and other control features, please

install the included Control Panel.

Insert the included “TOOLS for GO44/GO46” CD-ROM in the CD-ROM drive of

your computer.

2. Double-click on the CD-ROM drive icon and open [GO44Driver_] → [GO44

Setup.pkg] to start the InstallShield Wizard.

3. The welcome message of the InstallShield Wizard appears. Click [Continue].

4. Select the hard disk drive where the Mac OS is installed as the destination for the

installation. Click [Continue].

5. Click [Install] to start the installation.

6. Click [Restart] to complete the installation.

For information about the Control Panel, see page 19 of the PDF manual.

Assigning the GO44 as the default system audio

device (Mac OS X)

If you would like to use the GO44 not only for specific audio applications, but as your default

Mac OS X audio device, select the GO44 audio driver in the [Sound] control panel as the default

device for audio output.

Software Installation — Macintosh

users

NOTE

Front Panel

A PHONES jack

Output for a 1/4" stereo headphone jack. This signal output applies not only to that of the

OUTPUT 1/2 jacks (see Rear Panel), but also allows monitoring of other audio channels using

the GO44 Control Panel. (See page 19.)

B VOLUME control

Adjusts the output level of the PHONES jack. Turn this control to the right to increase the level,

and left to decrease it.

Rear Panel

C DC IN jack

Connects the AC power adaptor to this jack.

D IEEE1394 (FireWire) port

Connects the GO44 system to your computer using the included IEEE1394 (FireWire) cable.

E MIDI / DIGITAL jack

For connection of the included I/O cable (page 14), allowing input/output of digital audio

and MIDI data.

Connectors and controls

3 54 6 7

Connectors and controls

F INPUT 1/2 jacks

The GO44 System features two high-quality analog mono inputs. The connections have been

designed for balanced/unbalanced phone 1/4" jacks. The input levels for these jacks can be

selected from three different gain settings, HIGH, MID, and LOW. Refer to page 19 for details

on how to make these settings.

G OUTPUT 1/2 jacks

The connections have been designed for balanced/unbalanced phone 1/4" jacks for main out-

put. You can connect mixers, powered speakers, or ampliﬁers. The analog outputs operate

with instrument-compatible levels of 2.0 Vrms.

I/O cable

H MIDI IN jack

Connects MIDI devices such as MIDI keyboards and DAW controllers. For connecting MIDI

devices, connect the MIDI OUT terminal of the MIDI device to this jack using a MIDI cable.

I MIDI OUT jack

Connects to MIDI devices such as synthesizers and tone generators. For connecting MIDI

devices, connect the MIDI IN terminal of the MIDI device to this jack using a MIDI cable. This

can also be used as a MIDI Thru terminal, for MIDI sequence software that allows routing of

incoming MIDI data through the OUT jack, using a Thru (or MIDI Echo) function.

J DIGITAL IN jack

This coaxial type digital audio jack is for the digital input of audio signals. The interface can

receive sample rates of up to 24-bit/96 kHz. The input signal can be adjusted in the Digital

Mixer of the GO44 Control Panel. (See page 19.)

8 9 J K

Connectors and controls

When recording from a digital source, make sure that the sampling rates of both devices (e.g.

DAT recorder and laptop) are synchronized. The S/PDIF protocol contains a signal called

wordclock for this purpose. If the Master Clock switch is set to “EXTERNAL” in the GO44 Con-

trol panel, the GO44 will automatically synchronize to it and the “DIGITAL IN” channel will be

available in the mixer.

ASIO applications such as Cubase often have an option to switch the hardware from an inter-

nal to an external (sometimes also called S/PDIF) clock source. This changeover currently has

no effect on the GO44.

Make sure to use RCA pin cables specially made for digital audio applications.

K DIGITAL OUT jack

This digital audio jack is for the digital output of audio signals. The interface can transmit sam-

ple rates of up to 24-bit/96 kHz. For playback, set the routing in the Control Panel to the digi-

tal output. AC3 and DTS can also be played back via the digital output. Select “NON AUDIO”

for the digital output in the Control Panel under “ROUTING”. (See page 20.) The non-audio

signals are not sent to the analog outputs.

NOTE

Windows drivers

The GO44 audio interface features two kinds of audio drivers that support a variety of

applications. The audio drivers support all bit rates between 8 and 24 bits with all common

sample rates between 32 and 192 kHz. (Supports digital I/O up to 96 kHz)

MME driver

The Windows MME driver is a multi-channel driver that supports all channels of the GO44. The

specific routing options for these drivers can be found in the GO44 Control Panel. In most

Windows programs, you will encounter MME drivers with the designation “GO44(GO44 (1)) In

1” for input channel and “GO44(GO44 (1)) MC Out” for output channel.

ASIO driver

ASIO (Audio Streaming Input Output) is an audio transfer protocol developed by Steinberg. The

advantage of the ASIO driver is the extremely low audio recording and playback delay times, also

known as latency. Values of around 5 ms on fast, cleanly configured systems — at sample rates

exceeding 96 kHz — are quite realistic. The format also supports sound cards with multiple

inputs and outputs — so-called multi-I/O cards, as well as direct monitoring and multi-client

mode (ASIO 2.0 or later). In the programs that make use of Steinberg’s ASIO interface, the ASIO

driver for the GO44 is listed as “ASIO GO4x.”

Cubase LE

Drivers

For Cubase, the inputs are called “Line 1/2 left GO44”, “SPDIF left GO44”, etc. Also, the outputs

(generally called “busses” or “channels”) available in the individual programs are generally called

“Multichannel 1 GO44”, “SPDIF/AC3 left GO44”, etc.

Cubase LE

MIDI driver

This driver is for using the GO44 MIDI IN and MIDI OUT ports. The driver is designated as

“GO44(GO44 (1)) Midi In 1” (MIDI input) and “GO44(GO44 (1)) Midi Out 1” (MIDI output).

MIDI ﬁles, which can be played back using Windows’ media players, are also to be transferred to

externally connected devices such as synthesizers and tone generators. Open the “Sounds and

Audio Devices Properties” window from the Windows Control Panel, go to “Audio” and set the

“MIDI music playback” device to the driver mentioned above.

NOTE

Drivers

Mac OS X drivers

In Mac OS X, the GO44 system is supported completely by Apple CoreAudio and CoreMIDI.

Device-specific drivers are not required. If you would like to use the GO44 for the default system

sound output, select the GO44 audio driver in [System Preferences] → [Sound] → [Output].

The CoreAudio/MIDI driver can also be selected in DAW applications such as Cubase. Buffer sizes

generally can also be configured there to accelerate access to the audio system.

Cubase LE

The GO44 Control Panel is quite intuitive and should not present beginners with major problems.

Here, depending on the requirements of each situation, you can have total control of the audio

interface, reduce levels, route inputs to any output or set the Master Clock values.

The functions and the positions of the control elements are generally identical between the two

platforms, Windows and Mac OS. The following example illustrations have been taken from the

Windows version of the Control Panel.

MAIN display

In the MAIN display, you can control the digital mixer of the GO44, set sample rates, route any

input to any output, etc.

If you are working with common DAW applications, you should also use the DAW for level control.

The advantage for doing this is that the settings are usually saved together with your project (song,

arrangement etc.)

ANALOG IN / DIGITAL IN

Here you can control the levels of analog input channels in the ANALOG IN column and digital

input channels in the DIGITAL IN column. Use the faders to control the levels of corresponding

channels. The [MUTE] buttons can be used to mute the individual channels.

In the ANALOG IN column, you can set the gain levels of the INPUT 1/2 jacks. Click the pull-

down menu at the top of the ANALOG IN column and select from among the settings “LOW”,

“MID”, and “HIGH” for the input channels. Select “HIGH” to connect low-level equipment such

as microphones, and “LOW” to connect high, line-level equipment such as keyboards.

A separate fader is available for each mono channel. The individual channels can be joined using

the switchable stereo link function. To turn on/off the stereo link function, click the [PAIR] button.

While the stereo link function is active, faders and mute operations are linked.

DIGITAL IN is grayed out until a signal is applied to the digital input and the MASTER CLOCK

(page 20) is set to [EXTERNAL].

GO44 Control Panel

NOTE

GO44 Control Panel

DAW IN 1/2, 3/4, 5/6

Here you can adjust the levels of the output signals sent from DAW applications.

As with the ANALOG IN / DIGITAL IN, a separate fader is available for each mono channel. The

individual channels can be joined using the switchable stereo link function (the [PAIR] button).

While the stereo link function is active, faders and mute operations are linked.

To send the mixed signal, [DIGITAL MIXER] must be assigned in the ROUTING section. If

[DIGITAL MIXER] is not assigned for any outputs, the operation of the digital mixer is ignored.

MASTER

The overall playback level of the digital mixer can be set with the Master control. In Windows,

faders and mute operations can be linked using the stereo link function.

MASTER CLOCK

This controls the sample rate used by the GO44. When digital inputs are not used, click the

[INTERNAL] button and choose from all commonly used sample rates from 32 to 192 kHz from

the pull-down menu.

When external devices such as DAT recorders are connected, click the [EXTERNAL] button. The

external sample rate is displayed in the box next to the [EXTERNAL] button. If no signal is

available or the connection has been interrupted, the message “--------” will be returned.

• When a sample rate of 192kHz is selected, only the ANALOG IN (for audio inputs) and DAW IN 1/2 (for

audio outputs) columns are available.

• When a sample rate of 192kHz is selected, avoid using MIDI inputs and outputs since this may cause some

noise and glitches in the sound.

ROUTING

Selects the output signal sent from the OUTPUT 1/2, PHONES, and DIGITAL OUT jacks. All input

signals (DAW IN 1/2, DAW IN 3/4, DAW IN 5/6, ANALOG IN, DIGITAL IN, and DIGITAL MIXER)

can be routed to the three output pairs*. Click the three buttons on the left-hand side to open a

pull-down menu from which you can select the desired pair. If you intend to use the digital

mixer, [DIGITAL MIXER] must also be selected on the input side, otherwise the signal will be sent

straight to the output, bypassing the faders.

* For the DIGITAL OUT jack, you can select

“NON AUDIO” (as shown above). In this case,

AC3 and DTS data will be transmitted only via

the digital output.

SETTINGS

Calls up the ASIO control panel (for ASIO driver settings), the SCENES panel for saving the GO44

Control Panel settings, and the ABOUT display for system related information.

NOTE

Stránka se načítá ...

Yamaha GO44 Uživatelský manuál

Značka: Yamaha

Modelka: GO44

Kategorie: Hudební nástroje

Typ: Uživatelský manuál

Stáhnout PDF

zpráva

v jiných jazycích

polski: Yamaha GO44 Instrukcja obsługi
español: Yamaha GO44 Manual de usuario
italiano: Yamaha GO44 Manuale utente
Deutsch: Yamaha GO44 Benutzerhandbuch
svenska: Yamaha GO44 Användarmanual
português: Yamaha GO44 Manual do usuário
français: Yamaha GO44 Manuel utilisateur
Türkçe: Yamaha GO44 Kullanım kılavuzu
English: Yamaha GO44 User manual
dansk: Yamaha GO44 Brugermanual
русский: Yamaha GO44 Руководство пользователя
suomi: Yamaha GO44 Ohjekirja
Nederlands: Yamaha GO44 Handleiding
română: Yamaha GO44 Manual de utilizare

Yamaha GO44 Uživatelský manuál

Yamaha GO44 Uživatelský manuál

v jiných jazycích

Související papíry