Yamaha SPS-10MM Návod k obsluze

Typ
Návod k obsluze
ASSEMBLY
INSTRUCTIONS
Read this before use
SPEAKER STAND
SPS-10MM
Thank you for selecting the Yamaha SPS-10MM speaker stand.
This speaker stand is only for the speaker systems
listed in “USABLE SPEAKERS” below. Do not use the
speakers other than these listed.
To prevent the speaker from falling, use the screws
and parts provided with the stand.
To prevent the speaker stand from falling over, select
a location which is flat and stable.
To avoid accidents resulting from tripping over loose
speaker cables and to prevent the speaker stand from
falling over, fix the speaker cables to the wall, etc.
Do not let the children lean on the stand as this might
cause the serious accidents resulting from the falling
over of the speaker stand.
To prevent the speaker stand from discoloring and
warping, keep the speaker stand away from the
stoves and places where it will be exposed to direct
sunlight, etc.
Do not attempt to clean the speaker stand with
chemical solvents as this might damage the finish.
Use a clean, dry cloth.
Secure placement or installation is the owner’s
responsibility. YAMAHA shall not be liable for any
accident caused by improper placement or
installation of speakers.
PRECAUTIONS
618–868 (24-5/16”–34-3/16”)
282
(11-1/8”)
64
(2-1/2”)
21
(13/16”)
80
(3-3/16”)
300
(11-13/16”)
300
(11-13/16”)
60
(2-3/8”)
DIMENSIONS (mm/inch)
Top view
Front view
SPECIFICATIONS
Dimensions (W x H x D) : 300 x 618 – 868 x 300mm
(11-13/16” x 24-5/16
– 34-3/16” x 11-13/16”)
Weight : 1.6 kg (3 lbs. 8 oz.)
USABLE SPEAKERS
NS-10MM
NS-10MMT
NX-220P
(the main and rear speakers included in the NS-P220
speaker package)
NS-E104
(the rear speakers included in the NS-P320 speaker
package)
NS-E114
(the rear speakers included in the NS-P326 speaker
package)
NX-S100S
(the front and rear speakers included in the DVX-S100
sound system)
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Japan V816800-1
ASSEMBLY FIGURE
ASSEMBLY PROCEDURES
Before beginning assembly, check the parts list and make sure all the parts are included.
ASSEMBLY PROCEDURES
(You will need a screwdriver for assembly.)
1. Attaching the base and support.
Pass the support through the hole from the bottom of the base,
and fasten the + self-binding tapping screws
1.
Fix the support so that the holes for the screws comes to the
rear side.
Do not overtighten the + self-binding tapping screws 1.
Doing so may damage the screws or assembly.
2. Attaching the pole and support.
Insert the pole to the support, and fasten the hexagon socket
set screws 2 into the three hole on the support using the
included wrench 5.
The line on the pole shows the limit of the stand height. Do
not use the stand pulling out the pole above from this line.
The hexagon socket set screw 2 of the lower side becomes
ineffective and the fixation becomes unstable.
3. Attaching the pads.
Put the pads 4 to the four corners on the bottom of the base to
prevent the stand from moving rickety.
4.
Attaching the gaskets.
Put the gaskets 6 to the both side of the plate.
5.
Wiring the speaker cables.
Insert the speaker cables to the hole on the plate, and aligned
them to the grooved part on the bottom of the base.
6. Attaching the speakers.
Line up the holes on the bottom of the speaker and the center
hole on the plate, and fasten the + binding screws 3.
In order to ensure that the speakers do not fall, always hold
the speakers while attaching the speakers.
PARTS LIST
NAME PARTS NOS.
QUANTITY
1 + self-binding tapping screws EP040090 12
(4 x 12)
2 Hexagon socket set screws VV249400 7
3 + self-binding screws (4 x 8) EG340360 4
4 Pads VV249200 8
5 Wrench (hexagonal) VV249500 1
6 Gaskets VV249300 4
Speaker
Speaker
cable
Pole
Limit of the stand
height
Plate
Support
Base
6
3
6
3
2
2
4
1
1
4
5
  • Page 1 1
  • Page 2 2

Yamaha SPS-10MM Návod k obsluze

Typ
Návod k obsluze