Yamaha R-S201 Uživatelský manuál

Integrated Amplifier

Amplificateur Intégré

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

Printed in Malaysia ZH10650

Receiver

Ampli-Tuner

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around this unit.

Top: 30 cm (11-3/4 in)

Rear: 20 cm (7-7/8 in)

Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to an AC wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the AC wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from an AC wall

outlet or this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the AC wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press A (power) to set this unit

to standby mode, and then disconnect the AC power plug

from the AC wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

20 Install this unit near the AC wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

This label is required to be attached to a product of which

the temperature of the top cover may be hot during

operation.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed,

as a plug with bared flexible cord is hazardous if engaged

in a live socket outlet.

■ Special Instructions for U.K. Model

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as

it is connected to the AC wall outlet, even if this unit itself is turned

off by A. This state is called the standby mode. In this state, this

unit is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may

not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

Make sure that neither core is connected to the earth terminal of the

three pin plug.

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

English

USEFUL FEATURES ............................................ 1

SUPPLIED ACCESSORIES ................................. 1

CONTROLS AND FUNCTIONS ......................... 2

Front panel................................................................. 2

Front panel display .................................................... 4

Rear panel..................................................................5

Remote control........................................................... 6

Using the remote control ........................................... 8

CONNECTIONS .................................................... 9

Connecting speakers and source components............ 9

Connecting the FM and AM antennas..................... 11

Connecting power cable .......................................... 11

PLAYBACK ..........................................................12

Playing a source....................................................... 12

Using the sleep timer............................................... 13

FM/AM TUNING..................................................14

Using preset functions ............................................. 14

Receiving Radio Data System information

(Only for Europe model) ..................................... 18

SETTING THE OPTION MENU FOR EACH

INPUT SOURCE...............................................19

Option menu items................................................... 19

TROUBLESHOOTING .......................................20

SPECIFICATIONS...............................................23

■ About this manual

• y indicates a tip for your operation.

• The instructions in this manual describe the operation of this unit with the supplied remote control. You can also use the buttons or

knobs on the front panel if they have the same or similar names as those on the remote control.

This unit allows you to:

◆ Listen to FM and AM radio stations (see page 14)

◆ Use the remote control of this unit to operate a Yamaha

CD player (see page 7)

◆ Save power by using the AUTO POWER STANDBY

function (see page 19)

Please check that you received all of the following parts.

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

USEFUL FEATURES

SUPPLIED ACCESSORIES

Remote control

AM loop antenna

Batteries (x2)

(AA, R6, UM-3)

Indoor FM antennas

*

One of the above is supplied depending on the region of purchase.

2 En

INTRODUCTION

1 A (power)

Turns this unit on, or sets it to standby mode.

This unit consumes a small amount of power even when in

standby mode.

2 FM MODE

Changes the FM radio wave reception mode (stereo or

monaural) when TUNER is selected as the input

source (see page 14).

3 Remote control sensor

Receives infrared signals from the remote control.

4 STANDBY/ON indicator

5 MEMORY

Stores the current FM/AM station as a preset when

TUNER is selected as the input source (see page 15).

6 FM/AM

Sets the FM/AM tuner band to FM or AM when

TUNER is selected as the input source (see page 14).

7 PRESET j / i

Selects a preset FM/AM station when TUNER is

selected as the input source (see page 16).

8 TUNING jj / ii

Selects the tuning frequency when TUNER is selected

as the input source (see page 14).

9 Front panel display

Shows information about the operational status of this

unit.

CONTROLS AND FUNCTIONS

Front panel

Note

Indicator Status

Brightly lit

The power of this unit is “on”.

Dimly lit

This unit is in “standby” mode.

Off

The power of this unit is “off”.

To turn off this unit, disconnect

the power cable from an AC

wall outlet.

CONTROLS AND FUNCTIONS

3 En

INTRODUCTION

English

0 PHONES jack

Outputs audio to your headphones for private

listening.

Press SPEAKERS A/B so that the SP A/B indicators (see

page 4) turn off before you connect your headphones to the

PHONES jack.

A SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the

rear panel each time the corresponding button is

pressed (see page

12

).

B BASS –/+

Increases or decreases the low frequency response.

Control range: –10 dB to +10 dB

C TREBLE –/+

Increases or decreases the high frequency response.

Control range: –10 dB to +10 dB

D INPUT l / h

Selects the input source you want to listen to.

E VOLUME control

Increases or decreases the sound output level.

Note

CONTROLS AND FUNCTIONS

4 En

1 PRESET indicator

2 MEMORY indicator

3 SP (SPEAKERS) A/B indicators

Light up according to the set of speakers selected.

Both indicators light up when both sets of speakers are

selected.

4 TUNED indicator

Lights up when this unit is tuned in to an FM or AM

station with a strong signal.

5 SLEEP indicator

Lights up when the sleep timer is turned on (see

page 13).

6 ST indicator

Lights up when this unit is in stereo mode and tuning

in an FM station with a stereo broadcast.

7 kHz/MHz indicators

Lights up according to the current broadcast

frequency.

kHz: AM

MHz: FM

8 Multi-information display

Shows information when adjusting or changing

settings.

Front panel display

Indicator Status

lights up

Recalling a preset radio station.

Searching an FM/AM station

manually to register as a preset.

blinks

Scanning for FM stations

automatically to register as

presets.

Indicator Status

lights up

Registering an FM/AM station

as a preset has been completed.

blinks

Searching an FM/AM station

manually to register as a preset.

Scanning for FM stations

automatically to register as

presets.

CONTROLS AND FUNCTIONS

5 En

INTRODUCTION

English

1 ANTENNA terminals

Used to connect FM and AM antennas (see page 11).

2 Power cable

For connecting this unit to an AC wall outlet (see

page 11).

3 CD jacks

Used to connect a CD player (see page 9).

4 LINE 1-2 jacks

Used to connect audio components (see page 9).

5 LINE 3 jacks

PB (Playback) jacks

Used to connect to audio output jacks of an audio

component.

REC (Recording) jacks

Used to connect to audio input jacks of an audio

component.

6 SPEAKERS terminals

Used to connect speakers (see page 9).

7 VOLTAGE SELECTOR (Only for General

model)

Rear panel

CONTROLS AND FUNCTIONS

6 En

■ Common controls

The following parts and controls can be used no matter

which input source is selected.

1 Infrared signal transmitter

Sends infrared signals.

2

A (power)

Turns this unit on, or sets it to standby mode.

3 SLEEP

Sets the sleep timer (see page 13).

4 Input selector buttons

Select the input source you want to listen to.

y

• The input source names correspond to the names of the

connection jacks on the rear panel.

• To select TUNER as the input source using the remote

control, press FM or AM.

5 TREBLE –/+

Increases or decreases the high frequency response.

Control range: –10 dB to +10 dB

6 BASS –/+

Increases or decreases the low frequency response.

Control range: –10 dB to +10 dB

7 BALANCE L/R

Adjusts the sound output balance of the left and right

speakers to compensate for sound imbalances.

Control range:

8 B / C / D / E / ENTER

Selects and confirms items in the Option menu (see

page 19).

9 MENU

Turns the Option menu on and off (see page 19).

0 VOLUME +/–

Increases or decreases the sound output level.

A SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the

rear panel each time the corresponding button is

pressed (see page

12

).

B DIMMER

Select the brightness level of the front panel display

from 3 levels by pressing this button repeatedly.

y

• This setting is retained even if you turn off this unit.

• The default setting is the brightest.

C MUTE

Mutes the sound output. Press again to restore the

sound output to the previous volume level.

Remote control

(+20 dB) (center) (+20 dB)

The opposite side of

channel is muted.

The opposite side of

channel is muted.

CONTROLS AND FUNCTIONS

7 En

INTRODUCTION

English

■ FM/AM controls

The following buttons can be used when TUNER is

selected as the input source.

D TUNING jj / ii

Selects the tuning frequency (see page 14).

PRESET j / i

Selects a preset FM/AM station (see page 16).

MEMORY

Stores the current FM/AM station as a preset (see

page 15).

INFO

Only for Europe model:

Switches information shown on the front panel display

(see page 18).

■ Yamaha CD player controls

The following buttons can be used to control a Yamaha

CD player.

E Yamaha CD player control buttons

s Stops playback

e Pauses playback

p Starts playback

DISC SKIP Skips to the next disc in a CD changer

b Skips backward

a Skips forward

Ejects the disc

w Rewinds playback

f Fast-forwards playback

Even when using a Yamaha CD player, certain components and

features may not be available. Refer to your component’s owner’s

manual for more information.

Note

CONTROLS AND FUNCTIONS

8 En

■ Installing batteries ■ Operation range

Point the remote control at the remote control sensor on

this unit and remain within the operating range shown

below.

■ Notes on remote control and batteries

• The area between the remote control and this unit must be clear of large obstacles.

• Be careful not to spill water or other liquids on the remote control.

• Be careful not to drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bathroom

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Change all batteries if you notice the operation range of the remote control narrows.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a

different specification.

• Before inserting new batteries, wipe the battery compartment clean.

• Dispose of batteries according to your regional regulations.

• Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or her mouth.

• If you plan not to use this unit for a long period of time, remove the batteries from this unit. Otherwise, the batteries will wear out,

possibly resulting in a leakage of battery liquid that may damage this unit.

Using the remote control

AA, R6, UM-3 batteries

Approximately

6 m (20 ft)

Remote control

9 En

PREPARATION

English

PREPARATION

Make sure to connect L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will

be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and

lack bass. Refer to the owner’s manual for each of your components.

Make sure to use RCA cables to connect audio components.

• Do not connect this unit or other components to the main power until all connections between components are

complete.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the

speakers.

CONNECTIONS

Connecting speakers and source components

CAUTION

Audio

out

CD recorder,

etc.

DVD player,

etc.

Audio

out

Left

Audio

out

Audio

out

Audio

in

Speakers B

Tape deck, etc.

CD player

Speakers A

Right

LeftRight

10 En

CONNECTIONS

■ REC jacks

• The REC jacks output audio signals of the currently

selected input (except when LINE 3 is selected).

• Volume level, tone control and balance settings do not

affect the REC jacks.

■ Connecting speaker cables

When inserting speaker cables into the speaker terminals, insert

only the bare speaker wire. If insulated cable is inserted, the

connection may be poor and sound may not be heard.

Speaker impedance must be set as shown below.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section.

A bi-wire compatible speaker has four binding post

terminals. These two sets of terminals allow the speaker to

be split into two independent sections. With these

connections, the mid and high frequency drivers are

connected to one set of terminals and the low frequency

driver to another set of terminals.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker.

y

To use the bi-wire connections, press SPEAKERS A and

SPEAKERS B so that both SP A and B light up on the front panel

display.

Note

CAUTION

Speaker connection Speaker impedance

SPEAKERS A or

SPEAKERS B

8 Ω or higher

SPEAKERS A and

SPEAKERS B

16 Ω or higher

(except for North

America model)

Bi-wiring

8 Ω or higher

Remove approximately

10 mm (3/8 in) of

insulation from the end of

each speaker cable.

Note

Rear panel

Speaker

SPEAKERS A/B

11 En

CONNECTIONS

PREPARATION

English

Indoor antennas for receiving FM and AM broadcasts are

included with this unit. In general, these antennas should

provide sufficient signal strength. Connect each antenna

correctly to the designated terminals.

If you experience poor reception quality, install an outdoor

antenna. Consult the nearest authorized Yamaha dealer or service

center about outdoor antennas.

■ Assembling the supplied AM loop

antenna

■ Connecting the wire of the AM loop

antenna

Plug the power cable into an AC wall outlet after all other

connections are complete.

Only for General model:

Before connecting the power cable, make sure you set

VOLTAGE SELECTOR of this unit according to your

local voltage. Improper setting of VOLTAGE SELECTOR

may cause fire and damage to this unit.

Connecting the FM and AM

antennas

Note

Indoor FM

antenna

(included)

Outdoor AM antenna*

Outdoor FM antenna

AM loop

antenna

(included)**

*Outdoor AM antenna

Use 5 to 10 m of vinyl-covered wire extended outdoors from a

window.

**AM loop antenna (included)

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

• The AM loop antenna should be placed away from this unit.

• The wires of the AM antenna have no polarity.

Connecting power cable

CAUTION

To the AC wall

outlet with the

power cable

12 En

BASIC OPERATION

1 Press A (power) to turn on this unit.

2 Press one of the Input selector buttons to

select the desired input source.

3 Press SPEAKERS A and/or SPEAKERS B to

select desired speaker(s).

• When one set of speakers is connected using bi-wire

connections, or when using two sets of speakers simultaneously

(A and B), make sure SP A and SP B are displayed on the front

panel display.

• When listening with headphones, turn off the speakers.

4 Play the source.

5 Press VOLUME +/– to adjust the sound

output level.

y

You can adjust the tonal quality by using BASS –/+ and

TREBLE –/+, and the left/right sound balance of speakers

by using BALANCE L/R (see page 6).

6 When finished listening, press A (power) to

set this unit to standby mode.

Press A (power) to turn this unit on again.

y

• You can also use the buttons or knobs on the front panel if they

have the same or similar names as those on the remote control.

• For recording, see page 5.

PLAYBACK

Playing a source

A (power)

Input selector

buttons

SPEAKERS A/B

VOLUME +/–

TREBLE –/+

BASS –/+

BALANCE L/R

Notes

13 En

PLAYBACK

BASIC

OPERATION

English

Use this feature to automatically set this unit to standby

mode after a certain amount of time. The sleep timer is

useful when you are going to sleep while this unit is

playing or recording a source.

Press SLEEP repeatedly to set the amount of

time before this unit is set to standby mode.

Each time you press SLEEP, the front panel display

changes cyclically as shown below.

The SLEEP indicator blinks while setting the amount

of time for the sleep timer.

If the sleep timer is set, the SLEEP indicator on the

front panel display lights up.

y

To cancel the sleep timer, do one of the following:

– Select “SLEEP OFF”.

– Set this unit to standby mode.

Using the sleep timer

A (power)

SLEEP

14 En

• The radio frequencies differ depending on the country or region where this unit is being used. Front panel display illustrations shown

in this section are based on Europe model.

• Only for Asia and General models:

Be sure to set the tuner frequency step according to the frequency spacing in your area before you tune into a radio station (see

page 19).

1 Press FM/AM to select TUNER as the input

source and select the band.

2 Press and hold TUNING jj / ii to begin

tuning.

Press ii to tune in to a higher frequency.

Press jj to tune in to a lower frequency.

When this unit tunes in to a station, the TUNED

indicator lights up on the front panel display.

If the tuning search does not stop at the desired station because

the station signals are weak, press TUNING jj / ii repeatedly to

tune in to the desired station.

y

You can also use the buttons on the front panel if they have the

same or similar names as those on the remote control.

■ Improving FM reception

If the signal from the station is weak and the sound quality

is not good, set the FM band reception mode to monaural

mode to improve reception.

Front panel

Press FM MODE, and then make sure the ST indicator is

turned off (see page 4).

Remote control

Enter FM MODE from the Option menu to select MONO

(monaural mode) (see page 19).

You can register up to 40 radio stations as presets. Once

you have registered stations, you can easily tune in to

them by recalling the presets.

■ Presetting stations automatically

(FM stations only)

You can automatically register FM stations that have

strong signals.

• If a station is registered to a preset number that already has a

station registered to it, the previously registered station is

overwritten.

• If the station you want to store is weak in signal strength, press

TUNING jj / ii repeatedly to tune in to the desired station.

• Only for Europe model:

Only Radio Data System broadcasting stations can be preset

automatically.

y

FM stations registered as presets using the automatic preset

registration feature will be heard in stereo.

FM/AM TUNING

Notes

Note

TUNING jj / ii

FM/AM

Using preset functions

Notes

PRESET j / i

FM

B / C / D

ENTER

MENU

15 En

FM/AM TUNING

BASIC

OPERATION

English

1 Press FM to select TUNER as the input

source.

2 Press MENU to enter the Option menu.

The Option menu for TUNER is displayed (see

page 19).

3 Press B / C to select “AUTO PRESET”, and

then press ENTER.

This unit starts scanning the FM band about

3 seconds later from the lowest frequency upwards.

y

• Before scanning begins, you can specify the first preset

number to be used by pressing PRESET j / i or B/C.

• To cancel scanning, press D.

When a station to preset is found, information is

displayed on the front panel display as shown in the

illustration above.

When scanning is complete, “FINISH” is displayed,

and then the display returns to the Option menu.

To return the display to the original state, press

MENU.

■ Presetting stations manually

You can manually register the desired radio stations.

1 Tune in to the desired FM/AM station.

See page 14 for tuning instructions.

2 Press MEMORY.

“MANUAL PRESET” is displayed briefly on the

front panel display, and then the preset number to

which the station will be registered is displayed.

y

By holding down MEMORY for more than 2 seconds, you

can skip the following steps and automatically register the

selected station to an empty preset number (i.e., the preset

number following the last preset number used).

3 Press PRESET j / i to select the preset

number to which the station will be

registered.

When you select a preset number to which no station

is registered, “EMPTY” is displayed. When you

select a preset number to which a station has already

been registered, the frequency of the station is

displayed.

4 Press MEMORY.

When registration is complete, the display returns to

the original state.

y

• To cancel registration, switch input or band or do not perform

any operations for about 30 seconds.

• You can also preset stations manually by pressing buttons on

the front panel with the same names as remote control .

Preset number Frequency

PRESET j / i

MEMORY

Preset number

16 En

FM/AM TUNING

■ Recalling a preset station

You can recall preset stations that were registered by

presetting automatically or manually.

1 Press FM/AM to select TUNER as the input

source.

2 Press PRESET j / i to select a preset

number.

y

• Preset numbers to which no stations are registered are

skipped.

• If this unit does not have any preset stations, “NO

PRESET” is displayed.

• If the station signals that you want to recall are weak, try

tuning in to a station manually.

• You can also recall a preset station by pressing

PRESET j / i on the front panel.

■ Clearing a preset station

Follow the steps below to clear a preset station.

1 Press FM/AM to select TUNER as the input

source.

2 Press MENU to enter the Option menu.

The Option menu for TUNER is displayed (see

page 19).

3 Press B / C to select “CLEAR PRESET”, and

then press ENTER.

4 Select the desired preset station number by

pressing B / C repeatedly.

The selected preset number blinks on the front panel

display.

y

• You can also use PRESET j / i instead.

• To cancel clearing the preset station, press D or leave this

unit without any operations for about 30 seconds.

PRESET j / i

FM/AM

B / C / D

ENTER

MENU

FM/AM

PRESET j / i

17 En

FM/AM TUNING

BASIC

OPERATION

English

5 Press ENTER again to confirm.

“CLEARED” is displayed on the front panel display.

Then, another preset station is shown on the front

panel display. When there is no more preset station,

“NO PRESET” is displayed, and then the display

returns to the Option menu.

To return the display to the original state, press

MENU.

■ Clearing all preset stations

Follow the steps below to clear all preset stations.

1 Press FM/AM to select TUNER as the input

source.

2 Press MENU to enter the Option menu.

The Option menu for TUNER is displayed (see

page 19).

3 Press B / C to select “CLEAR ALL PRESET”,

and then press ENTER.

y

To cancel the operation and return to the Option menu,

press D.

4 Press B / C to select “CLEAR OK”, and then

press ENTER.

y

To cancel without clearing the presets, select “CLEAR NO”.

When all presets have been cleared, “CLEARED” is

displayed, and then the display returns to the Option

menu.

To return the display to the original state, press

MENU.

B / C / D

ENTER

FM/AM

MENU

18 En

FM/AM TUNING

Radio Data System is a data transmission system used by

FM stations in many countries.

1 Press FM to select TUNER as the input

source.

2 Tune in to the desired Radio Data System

broadcasting station.

3 Press INFO repeatedly to select the desired

Radio Data System display mode.

When you select Program Type, the following program

types can be displayed.

Receiving Radio Data System

information

(Only for Europe model)

Choice Description

Frequency This unit displays the

frequency of the current

station.

Program Service Default setting. This unit

displays the name of the Radio

Data System program currently

being received.

Program Type This unit displays the type of

the Radio Data System

program currently being

received.

Radio Text This unit displays about the

Radio Data System program

currently being received.

Clock Time This unit displays the current

time being received.

INFO

FM

Program type Description

NEWS

News

AFFAIRS

Current affairs

INFO

General information

SPORT

Sport

EDUCATE

Education

DRAMA

Drama

CULTURE

Culture

SCIENCE

Science

VARIED

Light entertainment

POP M

Popular music

ROCK M

Rock music

EASY M

Middle-of-the-road

music (easy listening)

LIGHT M

Light classics

CLASSICS

Serious classics

OTHER M

Other music

Stránka se načítá ...

Yamaha R-S201 Uživatelský manuál

Tato příručka je také vhodná pro

Yamaha R-S201 Uživatelský manuál

v jiných jazycích

Jiné dokumenty