Yamaha RS60A Návod k obsluze

Yamaha
Značka
Yamaha
Modelka
RS60A
Kategorie
Hudební bubny
Typ
Návod k obsluze
RS60A
q w e
r t y
e
e
w
q
w
t
y
w
w
r
3
4
1
2
YAMAHA
Electronic Drum Rack System
Assembly Instructions
Thank you for purchasing the Yamaha Electronic Drum Rack System RS60A.
Before using, thoroughly read this assembly manual, and use this product safely and correctly.
RS60A
● Pad and Drum Trigger Grouping (option)
qDTXPRESS
Drum Trigger Module
wTP60
Drum Pad
ePCY60
Cymbal Pad
rKP60
Kick Pad
tHH60
Hi-hat Control Pedal
yFoot Pedal
* FP-700 etc.
■ RS60A Rack Stand Parts ■ RS60A
+
Pad grouping : Set up example
* Before assembling the rack stand, make sure all of the parts shown below
are included.
Left Side Assembly (x1)
Center Pipe Assembly (x1)
Right Side Assembly (x1)
Module Holder (x1)
(4 screws included)
Module Holder Clamp (x1)
Hex Rod Cylinder (x6)
Drum Pad Clamp (x3)
Cymbal Holder (x2)
Cable Band (x10)
Tuning Key (x1)
Assembly Instructions
(this sheet)
Center Bar (x1)
e
e
w
q
w
t
y
w
w
r
* Specifications are subject to change without notice.
Before using, please read this “Assembly Instruction” sheet,
and use this product in a safe and proper manner.
Especially for children, parents or an instructor should teach the
children the proper manner in which to use the device.
Caution (including danger, or warning). This mark indicates
cautions in which you should pay close attention to.
Acts indicated with this icon are prohibited and should not
be attempted.
This icon indicates acts that you are urged to follow.
* Specifications are subject to change without notice.
Always set the instrument on a flat and solid surface.
Placement on a sloping, unstable surface or on steps
may result in the instrument being unstable and over-
turning.
Make sure all bolts are tightened firmly. Loose bolts
may result in the rack overturning or parts dropping
causing injury.
When adjusting the height or angle, do not suddenly
loosen the bolt. The pad may drop, the rack or pipes
may slip, pinching or causing injury to hands or fingers.
Do not sit or step on the rack. The rack may overturn
or be damaged resulting in injury.
Please be careful when children are close to or touch-
ing the product. The product has many pipes and arms
so careless movement around the product may result
in injury.
When setting the pads and modules, please pay close
attention in regards to the handling and setting of
cables. Feet may become entangled in the cables re-
sulting in falls.
If this symbol is ignored and the equipment is
used improperly, fatal injury to persons or se-
rious damage could occur.
Do not put your hands or feet under the foot pedal or
foot switch. They may be pinched resulting in injury.
Watch your fingers when adjusting clamps. They may
become pinched resulting in injury.
Be careful around pipe ends, inside the pipe and screw
ends. Metal shavings, etc. may injure your fingers.
Do not attach acoustic drums to the electronic drum
rack. Clamps may be damaged and drums may drop,
causing injury.
If this symbol is ignored and the equipment is
used improperly, there is a danger of injury to
persons handling the equipment, and material
damage could occur.
CAUTION
WARNING
3
Attach the Drum Pad Clamps
3-1 Insert the Hex Rod Cylinders into the Drum Pad Clamp ,
and tighten the fixing bolts.
3-2 Attach the Drum Pad Clamps
to the tom tom and hi-hat
locations.
3-3 Insert the Hex Rod Cylinder
into the Pads, adjust the angle
and secure.
4
1
Insert the Center Bar into the tube clamps on the Left Side As-
sembly
and Right Side Assembly . Then slide the tube
clamps on the Center Pipe
onto the Left and Right Side
Assemblies and tighten all fixing bolts.
2
Module Holder
DTXPRESS
Hex Rod Cylinder
Attach the Module Holder Clamp
Left Side Assembly
Hex Rod Cylinder
■ RS60A Assembly
* A screw driver (+ or -) is necessary to complete the assembly.
Step 4-2
Step 3-1
Step 4-1
Step 2-1
Step 2-2
Step 2-3
Step 2-4
Step 3-3
Step 3-2
Cymbal Pad
Tighten
Tighten
After the above assembly is complete, set the Kick Pad, Hi-Hat Con-
trol Pedal, etc. into position and connect the necessary cables. To
keep cable out of the way while playing, use the supplied Cable Bands
to hold the cables to the rack systems’s pipes.
Drum Pad Clamp
Cymbal Holder
Attach the Module Holder
2-1 Insert the Hex Rod Cylinder into the Module Holder Clamp
, and tighten the fixing bolts.
2-2 Attach the Module Holder Clamp
to the upright pipe on the
Left Side Assembly
.
2-3 Attach the DTXPRESS to the Module Holder
. Using a screw
driver and the supplied screws, attach the Module Holder
to
the screw hole on the bottom of the DTXPRESS.
2-4 Attach the Module Holder
, with the DTXPRESS attached,
to the Module Holder Clamp
.
Attach the Cymbal Holders
4-1 Insert the Cymbal Holders into the Cymbal Holder Clamps
that are attach to the left and right sides of the Center Pipe
,
and tighten all fixing bolts.
4-2 Attach the Cymbal Pad to the Cymbal Holders
, adjust the
position and tighten the fixing bolts. (Refer to the Cymbal Pad’s
Owner’s Manual for instructions on attaching the cymbal pad to
the cymbal holder.)
Please make sure that the fixing bolts on each part, such as clamps, pads, etc. are firmly tightened.
Bolts that are too tight or too loose may result in damage to the part or the part dropping. Please use caution.
Drum Pad
Cymbal Holder
Drum Pad Clamp
Attach the Center Pipe
Right Side Assembly
Tighten
Tighten
Left Side Assembly
Attach the Center Bar
Tighten
Tighten
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Yamaha RS60A Návod k obsluze

Yamaha
Značka
Yamaha
Modelka
RS60A
Kategorie
Hudební bubny
Typ
Návod k obsluze
Stáhnout PDF
zpráva

v jiných jazycích

Související papíry