Yamaha EMX 5000-20 Uživatelský manuál

Kategorie
Audio mixéry
Typ
Uživatelský manuál

Tato příručka je také vhodná pro

Owner’s Manual
E
Keep This Manual For Future Reference.
EMX5000-20/EMX5000-12
1
The Owner’s Manual Revisions
Thank you for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. Parts of the EMX5000-20, EMX5000-12 owner’s
manual have been revised. Please refer to the following revisions rather than the corresponding sections of the original owner’s
manual.
P.14
POWER amp section
X
LIMITER indicator
If the output level of signals received at the SPEAKERS
jacks (output of the internal power amplifier) reaches
maximum, the indicator will light.
P.15
Other indicators and controls
^
Level Meter
This LED display shows the
level of signals received at the
ST OUT jack (input/output
panel
0
).
P.18
Rear panel
3
SPEAKERS (speaker output) jacks
These jacks are used to connect speakers.
Jacks 1 are Speakon-type connectors. Use only Neutrik
NL4FC plugs for connecting Speakon connectors.
Jacks 2 are 1/4”phone jacks. The setting of the control
panel power amp select switch
Y
will determine the sig-
nal that is output to these jacks, and the number and
appropriate impedance of the speakers that can be con-
nected.
P.33
Block/Level Diagram
Power Amplifier output section level diagram (bottom right)
These plots show the nominal output and maximum output
levels of signals received at the SPEAKERS jacks. If the output
level is +4dB (Level Meter “0”), the internal power amplifier
will deliver 100W into a 4
load. If the output level is +11dB
(LIMITER indicator lights), the internal amplifier will deliver
a maximum of 500W into 4
.
E
Caution:
If the LIMITER indicator flashes continuous-
ly, the internal power amplifier section is being exces-
sively overloaded and may malfunction. Reduce the
output level at the ST OUT fader (
K
) below the level
that the indicator flashes only briefly on the highest
transient peaks.
Note:
The SPEAKERS 1 & 2 jacks (rear panel
3
) out-
put the signals received at the ST OUT jack via the inter-
nal power amplifier. Check the output signal level via
the LIMITER indicator (
X
). The LIMITER indicator
will light before the Level Meter “8” or “PEAK” LED
light.
X
`
2–
2+
1+
1–
Neutrik NL4FC
CHANNEL A
STEREO/PARALLEL BRIDGE
1+ A+
1– A–
2+ B+
2– B–
CHANNEL B
1+ B+
1– B–
1+ +
1–
2+
2–
+30dB
+20dB
+10dB
0dB
PA
+11dB
+4dB
SPEAKERS OUT
MAXIMUM OUTPUT [500W/4]
NOMINAL OUTPUT [100W/4]
6
EMX5000-20/EMX5000-12
Block/Level Diagram
CH INPUT
[–60~–16dB]
[–34~+10dB]
CH INSERT I/O
[0dB]
EMX5000-12:CH1-8
EMX5000-20:CH1-16
EMX5000-12:CH1-8
EMX5000-20:CH1-16
A
B
GAIN
[–60~–16dB]
[–34~+10dB]
PHANTOM
8CH/SW
EMX5000-12:[CH1-8]
EMX5000-20:[CH1-8] [CH9-16]
PA D
HPF
HPF
BA
HA
+48V
26dB
[0dB]
[0dB]
[0dB]
3-Stage EQ
Lo Gain
Hi Gain
Mid f
Mid Gain
BA
ON
[–10dB]
[0dB]
CH Fader
PEAK
SIGNAL
PA N
POST
PFL
POST
EFFECT1
EFFECT2
AUX1
AUX2
[0dB]
[–6dB]
[–6dB]
[–6dB]
[–6dB]
STEREO L (NON-MUTE)
STEREO R (NON-MUTE)
EFFECT1 (NON-MUTE)
EFFECT2 (NON-MUTE)
AUX1 (NON-MUTE)
AUX2 (NON-MUTE)
STEREO L (MUTE)
STEREO R (MUTE)
EFFECT1 (MUTE)
EFFECT2 (MUTE)
AUX1 (MUTE)
AUX2 (MUTE)
PFL L / AFL L
PFL R / AFL R
PFL
AFL
SUM
SUM
SUM
SUM
[0dB]
[0dB]
[0dB]
[0dB]
STAND-BY
EMX5000-12:CH1-8
EMX5000-20:CH1-16
SUM
SUM
[0dB]
[0dB]
REC OUT
[–10dBV]
L
R
9-Stage GEQ
9-Stage GEQ
63Hz
125Hz
250Hz
500Hz
1kHz
2kHz
4kHz
8kHz
16kHz
GEQ
BA
BA
BA
BA
[–6dB]
[–10dB]
ST OUT
ST SUB OUT
DR
DR
ST SUB OUT
[+4dB]
L
R
ST OUT
[+4dB]
L
R
PEAK
PEAK
YSP
YSP
POWER AMP IN
[+4dB]
YA MAHA
SPEAKER
PROCESSING
A
B
PA
LIMITTER
LIMITTER
PROTECTOR
Power Select
PA
SPEAKERS
[500Wmax@4ohms]
A
A
BRIDGE
B
2
1
1
2
500W
300W
100W
500W
300W
100W
+1
–1
+2
–2
+1
–1
+2
–2
POWER AMP Controls
INV
Signal Select
MAIN L
AUX1
AUX1
MONO BRIDGE
MAIN R
MONO
AUX2
MONO BRIDGE
FREQ
80–120Hz
(12dB/oct)
INV
LPF
LPF
SUM
MONO OUT
[+4dB]
[–10dB]
MONO OUT
BA
BA
AUX SEND1
[+4dB]
AUX SEND2
[+4dB]
[–10dB]
AUX1
[–10dB]
AUX2
AFL
AFL
AFL
SUM
SUM
SUM
[0dB]
SUM
[0dB]
SUM
[0dB]
[0dB]
[0dB]
SUM
[0dB]
SUMSUM
SUM
[–6dB]
SUM
[–6dB]
SUM
[0dB]
SUM
[0dB]
INV
[0dB]
INV
[0dB]
PFL
POST
POST
BAL
EFFECT1
EFFECT2
AUX1
AUX2
[0dB]
[–6dB]
[–6dB]
[–6dB]
[–6dB]
DN
BA
BA
[0dB]
[0dB]
[–10dB]
ST CH Fader
PEAK
SIGNAL
GAIN
[–34~+10dB]
ST CH INPUT
[–34~+10dB]
EMX5000-12:CH9(L)/10(R),CH11(L)/12(R)
EMX5000-20:CH17(L)/18(R),CH19(L)/20(R)
HA
HA
[0dB]
L
R
3-Stage EQ
3-Stage EQ
Lo
Hi
Mid
BA
BA
PA D
PA D
PFL
AUX1
ST
AUX2
[0dB]
[+4dB] [–6dB]
[–6dB]
[–6dB]
[–6dB]
[–16dB]
[–16dB]
ST SUB IN 1,2
[+4dB]
L (MONO)
R
2TR IN
[–10dBV]
BA
BA
[0dB]
[–6dB]
[–6dB]
L
R
PROGRAM
PARAMETER
PROGRAM
PARAMETER
DIGITAL
EFFECT1
ON
ON
IN
L OUT
R OUT
DIGITAL
EFFECT2
IN
L OUT
R OUT
ST
EFFECT1 RTN
EFFECT2 RTN
PFL
PFL
PFL
AUX1
AUX2
[–12dB]
[–12dB]
AUX1
AUX2
[–12dB]
[–12dB]
FOOT SWITCH
TA P
TA P
ON/OFF
0dB=0.775V
0dBV=1V
+30dB
+20dB
+10dB
0dB
–10dB
–20dB
–30dB
–40dB
–50dB
–60dB
ST CH INPUT
GAIN Min. [+10dB]
ST CH INPUT
GAIN Max. [–34dB]
CH INPUT A, B
GAIN Max. [–60dB]
CH INPUT A, B GAIN Min. [–16dB]
ST SUB IN [+4dB]
CH & ST CH to ST [0dB] (PAN, BAL turned hard left/right)
CH & ST CH to AUX/EFFECT [–6dB]
ST SUB IN to ST/AUX [–6dB]
2TR IN to ST [–6dB]
2TR IN [–10dBV]
fader [–10dB]
[PHONES 3mW@40ohms]
ST OUT•ST SUB OUT•MONO OUT [+4dB]
AUX SEND, EFFECT SEND [+4dB]
REC OUT [–10dBV]
PHONES [–16dB]
ST SUB level control [–6dB]
EFFECT [–6dB]
ST•MONO•AUX fader [–10dB]
SPEAKERS OUT
MAXIMUM OUTPUT [500W/4]
NOMINAL OUTPUT [100W/4]
+40dB
+30dB
+20dB
+10dB
0dB
–10dB
–20dB
–30dB
–40dB
–50dB
–60dB
INV
INV
INV
INV
EFFECT SEND1
[+4dB]
EFFECT SEND2
[+4dB]
PHONES
[3mW@40ohms]
[–16dB]
PHONES
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with
these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all
installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the
problem by using one of the following measures: Relocate either this product or the device that is being affected by the interference. Utilize power outlets that are on
different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in
is 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service
Division, 6600 Orangethorpe Ave, Buena Park, CA 90620
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magni-
tude to constitute a risk of electric shock to
persons.
The exclamation point within an equilat-
eral triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The above warning is located on the
rear of the unit.
European Specifications Only
This mark indicates a dangerous electrically live terminal.
When connecting an external wire to this terminal, it is
necessary either to have “a person who have received
appropriate guidance on handling” make the connection or to
use leads or a cord that have been manufactured in such a way
that the connection can be made simply and without problem.
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
GREEN-AND-YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured markings identifying the terminals in
your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be
connected to the terminal in the plug which is marked by the letter E
or by the safety earth symbol or coloured GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
* This applies only to products distributed by YAMAHA KEMBLE
MUSIC (U.K.) LTD.
Precautions
3
EMX5000-20/EMX5000-12—Owner’s Manual
Precautions
WARNING
Connect this unit’s power cord only to an AC outlet of the type
stated in this Owner’s Manual or as marked on the unit. Failure
to do so is a fire and electrical shock hazard.
Do not allow water to enter this unit or allow the unit to
become wet. Fire or electrical shock may result.
Do not place a container with liquid or small metal objects on
top of this unit. Liquid or metal objects inside this unit are a fire
and electrical shock hazard.
Do not place heavy objects, including this unit, on top of the
power cord. A damaged power cord is a fire and electrical shock
hazard. In particular, be careful not to place heavy objects on a
power cord covered by a carpet.
Use only the included power cord for this unit. Using other
types may be a fire and electrical shock hazard.
The power to this device is not completely shut off even when
the power switch is turned off. Locate the device close to the AC
outlet so you can easily reach the power plug.
Do not scratch, bend, twist, pull, or heat the power cord. A
damaged power cord is a fire and electrical shock hazard.
Do not remove the unit’s cover. You could receive an electrical
shock. If you think internal inspection, maintenance, or repair
is necessary, contact your dealer.
Do not modify the unit. Doing so is a fire and electrical shock
hazard.
If lightning begins to occur, turn off the power switch of the
unit as soon as possible, and unplug the power cable plug from
the electrical outlet.
If there is a possibility of lightning, do not touch the power
cable plug if it is still connected. Doing so may be an electrical
shock hazard.
If the power cord is damaged (i.e., cut or a bare wire is
exposed), ask your dealer for a replacement. Using the unit
with a damaged power cord is a fire and electrical shock hazard.
Should this unit be dropped or the cabinet be damaged, turn the
power switch off, remove the power plug from the AC outlet,
and contact your dealer. If you continue using the unit without
heeding this instruction, fire or electrical shock may result.
If you notice any abnormality, such as smoke, odor, or noise, or
if a foreign object or liquid gets inside the unit, turn it off
immediately. Remove the power cord from the AC outlet. Con-
sult your dealer for repair. Using the unit in this condition is a
fire and electrical shock hazard.
CAUTION
Keep this unit away from the following locations:
- Locations exposed to oil splashes or steam, such as near
cooking stoves, humidifiers, etc.
- Unstable surfaces, such as a wobbly table or slope.
- Locations exposed to excessive heat, such as inside a car with
all the windows closed, or places that receive direct sunlight.
- Locations subject to excessive humidity or dust accumula-
tion.
Hold the power cord plug when disconnecting it from an AC
outlet. Never pull the cord. A damaged power cord is a poten-
tial fire and electrical shock hazard.
Do not touch the power plug with wet hands. Doing so is a
potential electrical shock hazard.
This unit has ventilation holes at the rear to prevent the internal
temperature rising too high. Do not block them. Blocked venti-
lation holes are a fire hazard.
To relocate the unit, turn the power switch off, remove the
power plug from the AC outlet, and remove all connecting
cables. Damaged cables may cause fire or electrical shock.
Turn off all musical instruments, audio equipment, and speak-
ers when connecting to this unit. Use the correct connecting
cables and connect as specified.
Always lower the volume control to minimum before turning
on the power to this unit. A sudden blast of sound may damage
your hearing.
Use only speaker cables when connecting speakers to amplifier
outputs. Using other types of cables is a fire hazard.
If you know you will not use this unit for a long period of time,
such as when going on vacation, remove the power plug from
the AC outlet. Leaving it connected is a potential fire hazard.
Clean the contacts of the phone plug before connecting it to the
SPEAKERS jack of this unit. Dirty contacts may generate heat.
To prevent electrical shock when cleaning the unit, remove the
power plug from the AC outlet.
Installation
Operation
In case an abnormality occurs during operation
Installation
Operation
Maintenance
4
Precautions
EMX5000-20/EMX5000-12—Owner’s Manual
XLR-type connectors are wired as follows: pin 1: ground, pin 2:
hot (+), and pin 3: cold (–).
Insert TRS phone jacks are wired as follows: sleeve: ground, tip:
send, and ring: return.
The performance of components with moving contacts, such
switches, rotary controls, faders, and connectors, deteriorates
over time. The rate of deterioration depends on the operating
environment and is unavoidable. Consult your dealer about
replacing defective components.
Using a cell phone (mobile telephone) near this unit may induce
noise. If noise occurs, use the telephone away from the unit.
Do not set all equalizer controls and faders to maximum.
Doing so may cause oscillation depending on the condition of
the connected unit and speakers, and may damage the speakers.
The digital circuits of this unit may induce a slight noise into
nearby radios and TVs. If noise occurs, relocate the affected
equipment.
PRECAUTIONS FOR OPERATION – FOR CORRECT OPERATION –
Replacing abrasive parts
Connector pin assignments
Influence on cell phone usage
Volume level setting
Interference with other electronic devices
Introduction
5
EMX5000-20/EMX5000-12—Owner’s Manual
Introduction
Thank you for purchasing the Yamaha
EMX5000-20/EMX5000-12
Powered Mixer.
In order to take full advantage of the
EMX5000-20/EMX5000-12
and enjoy long,
trouble-free performance, please read this owner’s manual carefully, and keep it
in a safe place for future reference.
Features
The EMX5000-20/EMX5000-12 provides versatile
inputs, such as two stereo input channels and two ste-
reo sub inputs, as well as 16 (EMX5000-20), 8
(EMX5000-12) monaural input channels compatible
with mic/line signals. The mixer also has ample power,
with a maximum output of 500 W+500 W (1000 W
with bridge connection), and is suitable for a wide
range of applications from installed systems to small-
scale PA systems.
A two-channel power amp is built-in. The signals out-
put to speakers can be selected as stereo (ST L-R),
AUX+monaural (AUX 1- MONO), two AUX (AUX1-
AUX2) or monaural (bridge connection).
In addition to the speaker output jacks, two stereo
output channels for line-level signals, two AUX output
channels, two effect outputs, and one monaural out-
put are provided. You can easily expand the system by
adding a power amplifier or powered speakers.
The EMX5000-20/EMX5000-12 also has a PHONES
jack, which is very useful for checking the sound. You
can monitor only a specific channel or bus signal
through the headphones.
Each amp contains a limiter circuit to prevent distor-
tion due to excessive input levels.
A maximum output select switch lets you switch the
maximum output of the amp between three levels.
This lets you adjust the maximum output of the inter-
nal power amp as appropriate for the size of the room
or the input capacity of the speakers.
Two multi-effect units are built-in, each providing six-
teen types of effect equivalent in quality to the
acclaimed Yamaha SPX series of multi-effect units.
The effects can be used to add reverb or ambience to
vocals or instruments. The sixteen types (provided by
each of the two effect units) include TAP DELAY,
which lets you easily adjust the delay time.
The EMX5000-20/EMX5000-12 has implemented
“EEEngine”, Yamahas epochal amp drive technology
to create an unrivaled high-efficiency drive.
The EEEngine’s energy-saver/low-heat-generation
design has reduced power consumption to 50% or
less, and reduced heat generation to 35% or less (in
field applications, compared to Yamahas previous
models), and has lead to a reduction in energy cost
and to less-restrictive installation requirements related
to heat generation.
Contents
Introduction............................................................5
Features ................................................................5
EMX5000-20/EMX5000-12 Quick Guide ....................6
Front and rear panel..................................................10
Control panel.......................................................10
Input/output panel................................................16
Rear panel...........................................................18
Installation/Connections............................................19
Installation ...........................................................19
Connection ..........................................................19
Connecting input/output equipment.....................21
Basic operation .........................................................22
Connecting microphones and instruments..........22
Using the digital effect.........................................22
Example setups.........................................................24
As a conference/entertainment hall sound
system..............................................................24
As a band PA.......................................................26
Using a subwoofer...............................................28
Troubleshooting ........................................................29
Specifications............................................................30
General specifications.........................................30
Input specifications..............................................31
Output specifications...........................................31
Dimensions..........................................................32
Installing an optional rack mount kit ....................32
Block/Level Diagram............................................33
6
EMX5000-20/EMX5000-12 Quick Guide
EMX5000-20/EMX5000-12—Owner’s Manual
EMX5000-20/
EMX5000-12
Quick Guide
The following steps (1–5) explain the basic con-
nection and operation of the EMX5000-20/
EMX5000-12.
Also, please read “Front and Rear Panel” and
“Basic Operation following this Quick Guide
section to learn more about using the EMX5000-
20/EMX5000-12.
Connection
Connecting speakers
Using speaker cables, connect each speaker to the
SPEAKERS A jack and to the B jack in the
SPEAKERS jack section on the rear panel of the
EMX5000-20/EMX5000-12.
In the example shown by the above diagram, two
main speakers are connected (one each to left and
right) in stereo. For other connection examples,
refer to pages 20–21.
You may connect to either of the two jacks on the
speakers.
Be sure to use a cable designed for speaker connec-
tion.
Speakers with a Speakon connector can also be con-
nected using a Speakon cable. In this case, use the
SPEAKERS 1 jacks to output the signal from the
EMX5000-20/EMX5000-12.
When connecting a Speakon connector to the
EMX5000-20/EMX5000-12, be sure to turn the plug to
the right to lock the connection after inserting the plug.
Never connect the speakers in the manner shown
below. Otherwise, the EMX5000-20/EMX5000-
12’s built-in power amplifier will be damaged.
Setting the power amplifier mode
Set the power amp select switch (located on the
right corner on the panel) to ST L-R.
This quick guide explains how to connect one main
speaker each to left and right for stereo operation. If
the power amp select switch is set to the ST L-R
position as shown here, the stereo R signal will be
output from the SPEAKERS A jacks, and the stereo
L signal from the SPEAKERS B jacks.
Refer to pages 14, 19, 20 for other connections and
power amp select switch settings.
STEP 1
EMX5000-20 (EMX5000-12)
EMX5000-20 (EMX5000-12)
Power amp select switch
EMX5000-20
(EMX5000-12)
EMX5000-20/EMX5000-12 Quick Guide
7
EMX5000-20/EMX5000-12—Owner’s Manual
Connecting a microphone
Make sure that the power is turned off to the
EMX5000-20/EMX5000-12.
Connect mics to channels 1–16 (EMX5000-20)
or 1–8 (EMX5000-12), using the INPUT A jacks
if the mic has an XLR plug, or the INPUT B jacks
if the mic has a phone plug.
Using a condenser microphone
Turn on the PHANTOM switch (located in the upper
center corner on the panel).
The PHANTOM switch supplies phantom power to
all channel inputs at once (EMX5000-20: 1–8 and 9–
16, EMX5000-12: 1–8), so mics other than con-
denser mics must be connected to the INPUT B
jacks.
Do not connect or disconnect a condenser micro-
phone while the power to the unit is on and the
PHANTOM switch has been turned on.
Connecting a CD player, MD player, and/or cassette
deck
Connect a CD player or MD player to the 2TR IN
jacks. Refer to the operation manual of the corre-
sponding device for more information on the
input and output of the device.
To connect a second player, use the LINE jack.
Connect a recorder to the REC OUT jacks.
Connecting an electric acoustic guitar or electric
bass
Connect electric/acoustic guitars or electric
basses via an effect processor or direct box to the
INPUT B jack.
You cannot use the INPUT A jack and the INPUT B
jack for the same channel at the same time. If a
microphone has already been connected to the
INPUT B jack of a channel, you cannot connect the
effect unit to the INPUT A jack of the channel.
EMX5000-20 (EMX5000-12)
Microphone
EMX5000-20
(EMX5000-12)
PHANTOM switch
EMX5000-20
(EMX5000-12)
Recorder
(Cassette, DAT, MD)
CD player
EMX5000-20
(EMX5000-12)
Direct box
Effect unit
Electric-acoustic
guitar
Electric
bass
8
EMX5000-20/EMX5000-12 Quick Guide
EMX5000-20/EMX5000-12—Owner’s Manual
Connecting an electronic musical instrument
To the EMX5000-20/EMX5000-12’s LINE or ST
SUB IN jacks, you can connect an electronic
musical instrument such as a synthesizer, drum
machine, signal processor connected to an elec-
tric guitar, etc. Refer to the diagram below to
make a stereo connection from the output jacks
(such as L/MONO and R) of an electronic musi-
cal instrument to the LINE or ST SUB IN jacks in
stereo.
Power on
1 Turn on the power to all external devices con-
nected to the EMX5000-20/EMX5000-12.
2 Make sure that the ST OUT fader of the
EMX5000-20/EMX5000-12 is lowered, and then
press the POWER switch of the EMX5000-20/
EMX5000-12 to turn it on.
Be sure to follow the power up sequence specified
above to prevent the speakers from being damaged.
To correct the low range, turn on the YAMAHA
SPEAKER PROCESSING switch in the upper right
corner of the panel.
Sound output
Set the ST OUT fader and the input channel fad-
ers to the “–
position, and while playing the
instrument (or singing into the mic) connected
to the channel you want to check, raise the GAIN
control of the channel so that the PEAK indicator
of that channel lights occasionally.
Do not press the 26dB PAD switch if sound is input
from the microphone. Otherwise, press the 26dB
PAD switch on.
Set the ST OUT fader to the “0” position, and
raise the faders of the input channels to adjust the
volume.
Please be aware that if the PEAK indicator of the ST
level meter is continuously lit for an extended time,
the internal amp or the connected speakers may be
damaged.
EMX5000-20
(EMX5000-12)
Synthesizer,
Drum machine,
Guitar processor
STEP 2
EMX5000-20
(EMX5000-12)
STEP 3
EMX5000-20
(EMX5000-12)
EMX5000-20
(EMX5000-12)
EMX5000-20/EMX5000-12 Quick Guide
9
EMX5000-20/EMX5000-12—Owner’s Manual
Use the ST OUT fader to adjust the volume of the
speakers.
Applying built-in effects
1 Use the PROGRAM selector to select the type of
effect that you want to apply.
2 Turn on the ON switch in the EFFECT section.
The ON switch indicator lights up.
3 Set the EFFECT RTN fader to the “0” position.
4 If you want to use effect channel 1, adjust the
effect depth by turning the EFF1 control of the
channel to which you want to apply the effect.
Power off
1 Press the POWER switch of the EMX5000-20/
EMX5000-12 to turn off the power to the unit.
2 Turn off the power to all connected devices.
Be sure to follow the power off sequence specified
above to prevent the speakers from being dam-
aged.
• In preparation for the next time you will use the
EMX5000-20/EMX5000-12, we recommend that
you set the faders of the EMX5000-20/EMX5000-
12 to the “–
position.
EMX5000-20
(EMX5000-12)
STEP 4
EMX5000-20
(EMX5000-12)
2
1
EMX5000-20
(EMX5000-12)
3
EMX5000-20
(EMX5000-12)
4
STEP 5
10
Front and rear panel
EMX5000-20/EMX5000-12—Owner’s Manual
Front and rear panel
Control panel
Channel control section
In this section, you can adjust equalization (fre-
quency response), volume level, effect and AUX
output levels for the input signal of each channel.
1
26 dB pad switch
This switch attenuates the input signal by 26 dB.
Attenuation is on when the switch is pressed
inward.
2
GAIN control
Use this knob to adjust the sensitivity according
to the input signal level, so that the input level is
appropriate.
For the best balance of S/N ratio and dynamic
range, adjust this knob so that the peak indicator
0
lights occasionally.
* When the knob is at the position, the input
sensitivity will be +4 dB.
3
(High pass filter) switch
This is an on/off switch for the high-pass filter.
The high-pass filter is on when the switch is
pressed inward, and the frequency region below
80 Hz will be attenuated at 18 dB/octave.
4
Equalizer controls (HIGH, MID, LOW)
This is a 3-band equalizer that adjusts the high
frequency range, mid frequency range, and low
frequency range of each channel.
When the HIGH and LOW knobs are in the
position, the high and low ranges will have a flat
response. Turning a knob toward the right will
boost the corresponding frequency range, and
turning it toward the left will cut it.
For the mid range, use the upper MID knob to
specify the center frequency of the range, and use
the lower knob to set the amount of boost or cut
that will occur. The frequency response is flat
when the lower knob is set to the
position.
Turning the lower knob toward the right will
boost the corresponding frequency range, and
turning the knob toward the left will cut it.
The base frequency (or center frequency), range
of boost or cut, and equalizer type of each band
are as follows:
HIGH: 10kHz, ±15 dB, shelving type
MID: 250Hz–5kHz, ±15 dB, peaking type
LOW: 100Hz, ±15 dB, shelving type
1
3
2
4
5
7
9
4
5
8
9
A
A
C
C
B
B
2
66
0
0
*
Control panel
11
EMX5000-20/EMX5000-12—Owner’s Manual
5
AUX1, AUX2 controls / POST switches
These knobs adjust the level at which the input
signal will be sent to the AUX1 and 2 buses.
Nominal level is when the knob is set to the
position. The position from which the signal is
sent can be set by the POST switch to either pre-
fader (before the channel fader
C
) or post-fader
(after the channel fader
C
). When the switch is
pressed inward, post-fader is selected.
The signal will be output from the AUX1 and 2
buses to the AUX SEND 1 and 2 jacks of the
input/output section, and can be sent to external
monitor amps or powered speakers.
6
EFF 1, 2 controls (EFFECT)
For each channel, these control the amount of
signal that is sent to the EFFECT 1, 2 buses.
The signal of the EFFECT 1, 2 buses is sent to the
EFFECT SEND 1, 2 jack (input/output panel
9
).
It is also sent to the built-in effect when the ON
switch
S
in the digital effect section is turned on.
7
PAN (panpot) control
(EMX5000-20: Channels 1–16,
EMX5000-12: Channels 1–8)
The PAN knobs set the stereo position of the sig-
nal that is sent to the STEREO bus. The signal is
located in the center when the knob is positioned
at “
, at right at R, and at left at L.
8
BAL (balance) control
(EMX5000-20: Channels 17/18–19/20,
EMX5000-12: Channels 9/10–11/12)
The BAL knobs set the balance between the left
and right channels, and assign the signals
received at inputs 17/18–19/20, 9/10–11/12 to the
STEREO bus.
9
ON switch, indicator
This is an on/off switch for the input signal of
each channel. The indicator will light if this
switch is turned on.
0
PEAK indicator
The indicator will light 3 dB before clipping,
warning that clipping level is near.
A
SIGNAL indicator
This indicator will light if a signal is being input
to the corresponding channel.
B
PFL (pre-fader listen) switch
Channels for which this switch is on will send a
signal from a post-EQ pre-fader location to the
PHONES jack (input/output panel
D
). Use this
when you wish to use the headphones to monitor
only a specific channel.
C
Channel fader
This controls the output level of the input chan-
nel signal.
D PHANTOM indicator
This will light when the PHANTOM switch
(input/output panel 3) is on.
Stereo sub input section
In this section, you can adjust the input level of
external equipment connected to the ST SUB IN
1, 2 jacks on the input/output panel.
E AUX 1, 2 controls
This knob adjusts the amount of the signal sent
from the ST SUB IN 1 and 2 jacks (input/output
panel 7) to the AUX 1, 2 buses.
F ST (stereo) control
The ST knob adjusts the amount of stereo signal
sent from the ST SUB IN 1 and 2 jacks to the
STEREO bus.
Note: The amount of signal that is sent to the
EFFECT 1, 2 bus from each channel will be af-
fected not only by the setting of the EFFECT 1,
2 control, but also by the setting of the channel
fader C (post-fader send).
Note: If this switch is turned on, you can mon-
itor a channel even if the channel fader is low-
ered, or if the ON switch is off. This will not
affect the signals that are sent to the STEREO
bus, AUX 1 and 2 buses, and EFFECT bus.
D
F
G
F
E
G
E
12 Front and rear panel
EMX5000-20/EMX5000-12—Owner’s Manual
G PFL (pre-fader listen) switch
When this switch is turned on, the signal at the
point before the ST control knob F is sent to the
PHONES jack (input/output panel D).
Master control section
In this section, you can adjust the final level of
the outputs.
H AUX 1 fader
The AUX 1 fader adjusts the final level of the sig-
nal sent from the AUX 1 bus to the AUX SEND 1
jack (input/output panel 8). If the Power amp
select switch Y is set to AUX 1-MONO, using
this fader enables you to adjust the level of the
signal sent from the SPEAKERS A 1/2 jacks to the
speakers.
I AUX 2 fader
The AUX 2 fader adjusts the final level of the sig-
nal output from the AUX 2 bus to the AUX
SEND 2 jack (input/output panel 8). If the
Power amp select switch Y is set to AUX 1-
AUX 2, using this fader enables you to adjust the
level of the signal sent from the SPEAKERS B 1/2
jacks to the speakers.
J MONO OUT fader
The MONO OUT fader adjusts the final level of
the monaural signal output from the STEREO
bus to the MONO OUT jack (input/output panel
C).
If the Power amp select switch Y is set to AUX 1-
MONO, this fader also adjusts the level of the sig-
nal sent from the SPEAKERS B 1/2 jacks to the
speakers.
If the Power amp select switch Y is set to MONO
BRIDGE, this fader adjusts the level of the signal
sent from the SPEAKERS A 1 jacks to the speaker.
K ST OUT fader
The ST OUT fader adjusts the final level of the
signal sent from the STEREO bus to the ST OUT
jacks (input/output panel 0). If the Power amp
select switch Y is set to ST L-R, this fader also
adjusts the level of the signal sent to the SPEAK-
ERS jacks (rear panel 3).
L AFL (after fader listen) switch
When this switch is on, the output signal that
passes through the corresponding fader is sent to
the PHONES jack (input/output panel D). Use
these switches when you wish to monitor a par-
ticular output signal through the headphones.
2TR IN section
In this section, you can adjust the input level of a
cassette deck or a CD player that is connected to
the 2TR IN jacks (input/output panel 5).
M ST (stereo) control
This knob adjusts the level of the signal sent from
the 2TR IN jacks to the STEREO bus.
N PFL (pre-fader listen) switch
When this switch is on, the signal input from the
2TR IN jacks is routed at the point before the ST
control M to the PHONES jack (input/output
panel D).
Note: The ST control setting does not affect
the level of the signal sent to the PFL/AFL buses
(pre-fader send).
H I J K
L
Note: The setting of this fader does not affect
the signal output from the STEREO bus to the
ST SUB OUT jacks.
N
M
Control panel 13
EMX5000-20/EMX5000-12—Owner’s Manual
Digital effect section
This section enables you to turn the built-in two-
channel digital effects on/off and select the effect
type.
O PROGRAM selector
This knob selects the effect type for the internal
digital effect.
P PARAMETER control
This knob adjusts the time parameter of the
internal digital effect.
Q AUX 1/2 control
This knob adjusts the level of the return signal
that is sent from the built-in digital effect to the
AUX 1/2 buses.
R TAP switch, indicator
Only if the PROGRAM selector has selected
TAP DELAY as the internal effect type, you can
press this switch to set the desired delay time.
Press the TAP switch several times, and the inter-
val between the last two presses will be set as the
delay time. The specified time will be remem-
bered even if the power is turned off.
The LED beside the switch will blink in synchro-
nization with the delay time only when the effect
type is TAP DELAY.
S EFFECT 1/2 ON switch
This switch turns the internal digital effect on/
off.
T PFL (Pre-fader listen) switch
When this switch is on, the signal from before the
EFFECT 1/2 RTN faders U will be sent to the
PHONES jack (input/output panel D).
U EFFECT 1/2 RTN fader
This fader adjusts the level of the return signal
that is sent from the built-in digital effect to the
STEREO bus.
PP
OO
QQ
R
SS
TT
UU
14 Front and rear panel
EMX5000-20/EMX5000-12—Owner’s Manual
Graphic equalizer section
This section enables you to adjust the tone of the
STEREO bus signal.
V Graphic equalizer
This is a 9-band graphic equalizer that allows you
to adjust the frequency response of the STEREO
bus signal, providing a maximum of ±12 dB of
cut/boost for each frequency band.
This graphic equalizer affects both the STEREO
bus signal that is output to the speakers and the
line level signal that is output from the ST OUT
jacks (input/output panel 0), and MONO OUT
jack (input/output panel C).
W ON switch
This switch turns the graphic equalizer on/off.
Power amp section
This section allows you to select the signals that
will be sent to the built-in two-channel power
amplifier.
X LIMITER indicator
This indicator lights up when the level of the sig-
nal output from the power amp section reaches
the maximum and the limiter is activated. Adjust
the ST OUT K and appropriate fader so that the
indicator lights up for only a short while when
the signal reaches the maximum level.
Y Power amp select switch
Select one of the following three settings to spec-
ify the signals to be routed to the corresponding
jacks according to the speaker connection at the
SPEAKERS jacks 3 on the rear panel.
ST L-R
The STEREO bus signals are output from the
SPEAKERS A 1/2 jacks and the SPEAKERS B 1/2
jacks. The final level of these signals is adjusted by
the master ST OUT fader.
AUX 1-MONO
The AUX 1 bus signals are output from the
SPEAKERS A 1/2 jacks, and a monaural signal
that is a mix of the STEREO bus signals is output
from the SPEAKERS B 1/2 jacks. The final level of
these signals is adjusted by the master AUX 1
fader and the MONO OUT fader.
AUX 1-AUX 2
The AUX 1, 2 buses signals are output from the
SPEAKERS A 1/2 jacks and the SPEAKERS B 1/2
jacks.
MONO BRIDGE
The monaural signal that is a mix of the STEREO
bus is output from the SPEAKERS A 1 jack. The
final level of this signal is adjusted by the master
MONO OUT fader.
Set the switch to this position when you connect
only one speaker to play a loud sound.
Z Maximum output select switch
This switch lets you change the maximum output
level of the two internal power amps between
three levels.
Set this as appropriate for the size of the room or
the input capacity of the speakers.
• 500W + 500W
The two internal amps will produce a maximum
of 500W + 500W/4.
• 300W + 300W
The two internal amps will produce a maximum
of 300W + 300W/4.
• 100W + 100W
The two internal amps will produce a maximum
of 100W + 100W/4.
Note: The indicator lights up or flashes for a
longer duration if the power amp section is sig-
nificantly overloaded, which could result in
malfunction. Avoid such a situation.
V
W
X
Y
Z
Control panel 15
EMX5000-20/EMX5000-12—Owner’s Manual
POWER indicator
[ POWER indicator
This indicator will light up when the power of the
EMX5000-20/EMX5000-12 is turned on.
YAMAHA SPEAKER PROCESSING
\ ON/OFF switch
This switch enables you to compensate the low
range of the speakers. The low range balance
when this switch is on varies depending on the
speakers.
First, check the low range balance by auditioning
the resultant sound, then set this switch to on or
off.
STAND-BY
] ON/OFF switch
This switch mutes (silences) the input signals
from channels 1–16 (EMX5000-20) or channels
1–8 (EMX5000-12). The indicator will blink
when this switch is on.
Other indicators and controls
^ Peak level indicator
This indicator allows you to monitor the level of
the signal output from the ST OUT jacks. The “0”
indicator lights up when the output level reaches
+4 dB.
a PHONES control
This knob adjusts the level of the signal moni-
tored via the PHONES jack (input/output panel
D).
b ST SUB OUT control
This knob adjusts the final level of the signal sent
from the STEREO bus to the ST SUB OUT jacks
(input/output panel A).
c LPF control, ON/OFF switch
This switch applies a low-pass filter to the signal
that is output from the PFL/AFL bus to the
MONO OUT jack. The frequency is indicated by
the position of the slit in the control trimmer that
is set into the panel above the switch. To adjust
the frequency, use a slotted screwdriver to turn
the control to the desired position. This will out-
put the region below the frequency (80–120 Hz)
you specify by the control knob.
Use this when you are using a sub-woofer.
[
\
]
Note: The setting of this control does not affect
signals that are sent from the STEREO bus to
the ST SUB OUT jacks and the SPEAKERS
jacks.
c
`
b
a
16 Front and rear panel
EMX5000-20/EMX5000-12—Owner’s Manual
Input/output panel
1 Channel input jacks (INPUT A, INPUT B)
EMX5000-20: 1–16, EMX5000-12: 1–8
By using the GAIN control (control panel 2)
you can connect any of the jacks to a wide range
of sources, from mics to line-level devices
(including synthesizers and rhythm machines).
The INPUT A jacks can provide +48V phantom
power, allowing you to use condenser micro-
phones.
The nominal input level is from –16 dB to –60 dB
when the 26 dB pad switch (control panel 1) is
off, or from +10 dB to –34 dB when it is on.
Both INPUT A and B are balanced.
They are compatible with microphones of output
impedance 50–600 or line level devices of
600.
Pin connections for the jacks are as follows:
* You can also connect a normal unbalanced phone plug.
2 INSERT I/O (insert) jacks
These are TRS phone jacks that enable you to
insert an external effect processor, such as a com-
pressor/limiter, between the equalizer and fader
of input channels. These connections require a
special “Y” cable, such as shown in the following
diagram. The nominal input/output levels are
0 dB.
A56 8
EF
G
0
D
1
43
2
7B
C
9
INPUT A jacks
(XLR type)
INPUT B jacks
(TRS phone jacks) *
Pin 1: ground Sleeve: ground
Pin 2: hot (+) Tip: hot (+)
Pin 3: cold (–) RIng: cold (–)
GND
RST
+-
GND
+-
12
3
Note: It is not possible to simultaneously use
both the INPUT A and B inputs of a given
channel. For each channel, use only one of the
inputs as appropriate for the input source.
Phantom power is switched on/off simulta-
neously for channels 1–8 and 9–16 (EMX5000-
20), 1–8 (EMX5000-12). For this reason, devic-
es (in particular, unbalanced devices) other
than condenser microphones must be connect-
ed to the INPUT B input jacks of channels or
channel 17/18–19/20 (EMX5000-20), 9/10–11/
12 (EMX5000-12) input jacks if the PHAN-
TOM +48V switch (control panel 3) is on.
to the input jack of
the external processor
to the output jack of
the external processor
to the INSERT I/O jack
Tip
Tip
Ring
Sleeve
Sleeve
Input/output panel 17
EMX5000-20/EMX5000-12—Owner’s Manual
3 PHANTOM switch
This is an on/off switch for the phantom power
supplied to the INPUT A jacks of channels 1–8
and 9–16 (on the EMX5000-20) or channels 1–8
(on the EMX5000-12). When this switch is on,
the indicator in the upper part of the control
panel will light.
4 LINE (stereo) input jacks
EMX5000-20: 17/18–19/20,
EMX5000-12: 9/10–11/12
These are the input jacks for channels 17/18–19/
20, 9/10–11/12 and are used to connect to the ste-
reo output jacks of electronic instruments, cas-
sette decks, or CD players.
You can connect either phone plugs or RCA
phono plugs, as appropriate for the type of jack
on the device you are connecting. The nominal
input level is from –34 dB to +10 dB.
5 2TR IN jacks
These are phono jacks that allow the signal from
an external device, such as a cassette deck and CD
player, to be added to the STEREO bus. The
nominal input level is –10 dBV.
6 REC OUT jacks
These phono jacks are used to connect to the
inputs of a recording device, such as a cassette
deck, to record the signal from the STEREO bus.
The nominal output level is –10 dBV.
7 ST SUB IN 1 (stereo sub 1) jacks
ST SUB IN 2 (stereo sub 2) jacks
These phone jacks are used to connect stereo out-
puts of a sub mixer or external effect processor.
The signal input here can be routed to the AUX 1
bus, AUX 2 bus, and STEREO bus. The nominal
input level is +4 dB.
8 AUX SEND 1 jack, AUX SEND 2 jack
These phone jacks output the line-level signals of
the AUX 1/2 buses. Connect stage-monitoring
amplifiers or powered speakers here. Use the
AUX 1 fader (control panel H) and the AUX 2
fader (control panel I) respectively to adjust the
final level of the signals output from these jacks.
The nominal output level is +4 dB.
9 EFFECT SEND 1 jack, EFFECT SEND 2 jack
The input of an external effect unit such as a
delay or echo can be connected to this jack.
The signal adjusted by the EFF 1, 2 control of
each channel will be sent to the EFFECT 1, 2 bus,
and output from this jack.
The nominal output level is +4 dB.
0 ST OUT jacks
These phone jacks output the line level signal of
the STEREO bus. The final output level from
these jacks is adjusted by the ST OUT fader (con-
trol panel K). The nominal output level is +4 dB.
A ST SUB OUT jacks
These phone jacks output the line-level signals of
the STEREO bus. Connect an external mixer or
additional PA system to these jacks.
Use the ST SUB OUT control (control panel b)
to adjust the final output level at the ST SUB
OUT jacks.
The nominal output level is +4 dB.
B P.AMP IN A, B (power amp input) jacks
These phone jacks are used to input line-level ste-
reo signals to the two-channel built-in power
amplifier. Connect an external mixer output here.
The nominal input level is +4 dB.
C MONO OUT jack
This phone jack mixes the STEREO bus signals
and output a monaural signal. Connect an addi-
tional PA system here. Use the MONO OUT
fader (control panel J) to adjust the final level of
the signal output from this jack. The nominal
output level is +4 dB.
D PHONES jack
This is a stereo phone type output jack, and is
used to monitor the channels selected by the PFL
switches on the front panel and the buses selected
by the AFL switches.
The nominal output is 3mW when headphones
are connected.
E FOOT SW EFFECT 2 ON/OFF jack
A separately sold Yamaha FC5 foot switch can be
connected to this jack so you can use your foot to
switch the built-in digital EFFECT 2 on/off.
Note: The setting of the graphic equalizer or
ST OUT fader on the control panel does not af-
fect the signals output from these jacks. Adjust
the recording level on the recording device.
Note: Use only the L jack to connect a monau-
ral output device.
Note: If you insert a plug into this jack, the cor-
responding channel of the power amplifier will
be isolated, and no signals will be sent from the
mixer section.
18 Front and rear panel
EMX5000-20/EMX5000-12—Owner’s Manual
F FOOT SW (EFFECT 2) TAP jack
When TAP DELAY is selected as the internal
effect type for the EFFECT 2 RTN channel, you
can connect a separately sold FC5 foot switch to
this jack, and press the foot switch to set the delay
time to the corresponding interval. When you
press the foot switch several times, the delay time
will be set to the interval between the last two
presses.
G LAMP jack
This is an XLR (3-pin female) output jack that
supplies power to a lamp.
Rear panel
1 AC inlet
Connect the socket end of the included AC cable
to this inlet. Connect the plug end of the cable to
an AC outlet of the voltage printed below the
inlet.
2 POWER switch
This switch turns on/off the power to the
EMX5000-20/EMX5000-12.
3 SPEAKERS (speaker output) jacks
These jacks are used to connect speakers.
Jacks 1 are Speakon-type connectors. Jacks 2 are
1/4" phone jacks. The setting of the control panel
power amp select switch Y will determine the
signal that is output to these jacks, and the num-
ber and appropriate impedance of the speakers
that can be connected.
21
3
Note: Before you turn the power of the
EMX5000-20/EMX5000-12 on or off, the fad-
ers and controls in the master section of the
control panel must be lowered to the minimum
position.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Yamaha EMX 5000-20 Uživatelský manuál

Kategorie
Audio mixéry
Typ
Uživatelský manuál
Tato příručka je také vhodná pro