Yamaha MG166CX Návod k obsluze

Yamaha
Značka
Yamaha
Modelka
MG166CX
Kategorie
Audio mixéry
Typ
Návod k obsluze
EN
DE
FR
ES
EnglishDeutschFrançaisEspañol
Features
Input Channels...................................................................page 12
With up to 16 (MG166CX/MG166C: 10) mic/line inputs or up to four
stereo inputs, the MG mixer can simultaneously connect to a wide
range of devices: microphones, line-level devices, stereo
synthesizers, and more.
Compression......................................................................page 10
Compression increases the overall level without introducing
distortion by compressing excessive peaks in the signals from
microphones and guitars.
AUX Sends and Stereo AUX Return.................................page 16
You can use the AUX SEND jack to feed the signal sent to an
external signal processor, and then return the processed stereo
signal through the RETURN jack.
High-quality digital effects (MG166CX)....................pages 15, 19
With digital effects built in, the MG166CX can deliver a wide range
of sound variations all by itself.
Caractéristiques
Canaux d’entrée.................................................................page 48
Avec 16 entrées micro/ligne (MG166CX/MG166C: 10) ou quatre
entrées stéréo maximum, la console de mixage MG peut connecter
simultanément une grande variété d’appareils : micros, appareils
de ligne, synthétiseurs stéréo, etc.
Compression......................................................................page 46
La compression augmente le niveau général sans engendrer de
distorsion en comprimant les pics excessifs des signaux des
micros et des guitares.
Envois AUX et retour AUX stéréo.....................................page 52
Vous pouvez utiliser la prise jack AUX SEND pour envoyer le signal
vers une unité de traitement de signaux externes, puis pour
renvoyer le signal stéréo traité via la prise jack RETURN.
Effets numériques de qualité supérieure (MG166CX)
...pages 51, 55
Grâce aux effets numériques intégrés, la console MG166CX peut
proposer de nombreuses variations de sons.
Funktionen
Eingangskanäle..................................................................Seite 30
Mit bis zu 16 Mikrofon-/Line-Eingängen (MG166CX/MG166C: 10)
oder bis zu vier Stereoeingängen können viele Geräte gleichzeitig
am MG-Mischpult angeschlossen werden: Mikrofone, Geräte mit
Leitungspegel, Stereo-Synthesizer uvm.
Kompression......................................................................Seite 28
Kompression erhöht den Durchschnittspegel, ohne Verzerrung
hinzuzufügen, indem übermäßige Pegelspitzen der Signale von
Mikrofonen oder Gitarren komprimiert werden.
AUX Sends und Stereo AUX Return.................................Seite 34
Von der AUX SEND-Buchse können Sie das Signal einzeln an
einen externen Signalprozessor führen, und das verarbeitete
Stereosignal über die RETURN-Buchse zurück in das Pult führen.
Hochwertige Digitaleffekte (MG166CX)....................Seiten 33, 37
Mit den eingebauten digitalen Effekten kann das MG166CX aus
sich heraus eine Reihe von Klangvariationen liefern.
Características
Canales de entrada.........................................................página 66
Con un máximo de 16 entradas de micrófono/línea
(MG166CX/MG166C: 10) o cuatro entradas estereofónicas, la
mezcladora MG puede conectarse simultáneamente con una gran
variedad de dispositivos: micrófonos, dispositivos de nivel de línea,
sintetizadores estereofónicos, etc.
Compresión.....................................................................página 64
La compresión aumenta el nivel general sin causar distorsión,
mediante la compresión del exceso de picos en las señales de los
micrófonos y guitarras.
Envíos AUX y retorno AUX estereofónico....................página 70
Puede utilizar la toma AUX SEND para introducir la señal enviada
en un procesador de señales externo y luego devolver la señal
estereofónica procesada a través de la toma RETURN (retorno).
Efectos digitales de alta calidad (MG166CX)........páginas 69, 73
Gracias a sus efectos digitales incorporados, la mezcladora
MG166CX puede producir por sí misma una amplia gama de
variaciones de sonido.
Owner’s Manual
Bedienungsanleitung
Mode d’emploi
Manual de instrucciones
MG206C/MG166CX/MG166C Owner’s Manual
2
* This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (2 wires)
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured makings identifying the terminals
in your plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions
contained in this manual, meets FCC requirements. Modifi-
cations not expressly approved by Yamaha may void your
authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories
and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all
installation instructions. Failure to follow instructions could
void your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15 for
Class “B” digital devices. Compliance with these require-
ments provides a reasonable level of assurance that your use
of this product in a residential environment will not result in
harmful interference with other electronic devices. This
equipment generates/uses radio frequencies and, if not
installed and used according to the instructions found in the
users manual, may cause interference harmful to the opera-
tion of other electronic devices. Compliance with FCC regula-
* This applies only to the MG166CX distributed by YAMAHA CORPORATION OF AMERICA, not the MG206C/MG166C. (class B)
tions does not guarantee that interference will not occur in all
installations. If this product is found to be the source of inter-
ference, which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using one of
the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to distrib-
ute this type of product. If you can not locate the appropriate
retailer, please contact Yamaha Corporation of America,
Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distrib-
uted by Yamaha Corporation of America or its subsidiaries.
FCC INFORMATION (U.S.A.)
MG206C/MG166CX/MG166C Owner’s Manual
3
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Only use the voltage specified as correct for the device. The required voltage is
printed on the name plate of the device.
• Use only the included power adaptor (PA-30 or an equivalent recommended by
Yamaha).
• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
• Do not open the device or attempt to disassemble the internal parts or modify
them in any way. The device contains no user-serviceable parts. If it should
appear to be malfunctioning, discontinue use immediately and have it inspected
by qualified Yamaha service personnel.
• Do not expose the device to rain, use it near water or in damp or wet conditions,
or place containers on it containing liquids which might spill into any openings.
• Never insert or remove an electric plug with wet hands.
• If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the device, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the device inspected by
qualified Yamaha service personnel.
• If this device or the AC power adaptor should be dropped or damaged,
immediately turn off the power switch, disconnect the electric plug from the
outlet, and have the device inspected by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the device or other property. These precautions include, but are not limited to, the following:
• Remove the electric plug from the outlet when the device is not to be used for
extended periods of time, or during electrical storms.
• When removing the electric plug from the device or an outlet, always hold the
plug itself and not the cord. Pulling by the cord can damage it.
•To avoid generating unwanted noise, make sure there is adequate distance (50
cm or more) between the AC power adaptor and the device.
• Do not cover or wrap the AC power adaptor with a cloth or blanket.
• Before moving the device, remove all connected cables.
• When setting up the device, make sure that the AC outlet you are using is easily
accessible. If some trouble or malfunction occurs, immediately turn off the
power switch and disconnect the plug from the outlet. Even when the power
switch is turned off, electricity is still flowing to the product all the minimum
level. When you are not using the product for a long time, make sure to unplug
the power cord from the wall AC outlet.
• If this device is to be mounted in an EIA-standard rack, leave the back of the rack
open and make sure that it is at least 10 cm away from walls or surfaces. Also, if
this device is to be mounted with devices that tend to generate heat, such as
power amplifiers, be sure to keep an adequate gap between this device and the
heat-generating devices or install ventilation panels to prevent high
temperatures from developing inside this device.
Inadequate ventilation can result in overheating, possibly causing damage to the
device(s), or even fire.
•Avoid setting all equalizer controls and faders to their maximum. Depending on
the condition of the connected devices, doing so may cause feedback and may
damage the speakers.
• Do not expose the device to excessive dust or vibrations, or extreme cold or heat
(such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration or damage to the internal components.
• Do not place the device in an unstable position where it might accidentally fall
over.
• Do not block the vents. This device has ventilation holes at the bottom/rear to
prevent the internal temperature from becoming too high. In particular, do not
place the device on its side or upside down. Inadequate ventilation can result in
overheating, possibly causing damage to the device(s), or even fire.
• Do not use the device in the vicinity of a TV, radio, stereo equipment, mobile
phone, or other electric devices. Doing so may result in noise, both in the device
itself and in the TV or radio next to it.
Power supply/Power cord
Do not open
Water warning
If you notice any abnormality
Power supply/Power cord
Location
(5)-4 1/2
MG206C/MG166CX/MG166C Owner’s Manual
4
• Before connecting the device to other devices, turn off the power for all devices.
Before turning the power on or off for all devices, set all volume levels to
minimum.
• When turning on the AC power in your audio system, always turn on the power
amplifier LAST, to avoid speaker damage. When turning the power off, the power
amplifier should be turned off FIRST for the same reason.
• Do not insert your fingers or hands in any gaps or openings on the device
(vents, etc.).
•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any
gaps or openings on the device (vents, etc.) If this happens, turn off the power
immediately and unplug the power cord from the AC outlet. Then have the
device inspected by qualified Yamaha service personnel.
• Do not use the device or headphones for a long period of time at a high or
uncomfortable volume level, since this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the ears, consult a physician.
• Do not rest your weight on the device or place heavy objects on it, and avoid use
excessive force on the buttons, switches or connectors.
Always turn the power off when the device is not in use.
Even when the power switch is in the “STANDBY” position, electricity is still flowing to the device at the minimum level. When you are not using the device for a long time,
make sure you unplug the power cord from the wall AC outlet.
The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualified Yamaha service
personnel about replacing defective components.
The MG mixer may heat up by as much as 15 to 20°C while the power is on. This is normal. Please note that the panel temperature may exceed 50°C in ambient temperatures
higher than 30°C, and use caution to prevent burns.
* This Owner’s Manual applies to the MG206C/MG166CX/MG166C. The main differences between the three models are the number of input channels and whether the
internal effects are included. The MG206C has 20 input channels while the MG166CX/MG166C have 16 channels. And only the MG166CX has internal effects.
* In this manual the term “MG mixsers” refers to the MG206C, MG166CX and MG166C.
* Illustrations herein are for explanatory purposes only, and may not match actual appearance during operation.
* Company names and product names herein are trademarks or registered trademarks of their respective companies.
Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
Connections Handling caution
XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
Insert TRS phone jacks are wired as follows: sleeve: ground, tip: send, and ring: return.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the device, or data that is lost or destroyed.
Copying of commercially available music or other audio data for purposes other than personal use is strictly prohibited by copyright law. Please respect all
copyrights, and consult with a copyright specialist if you are in doubt about permissible use.
(5)-4 2/2
MG206C/MG166CX/MG166C Owner’s Manual
5
Introduction .......................................... 5
Contents...........................................................5
Before Turning on the Mixer ............................5
Turning the Power On......................................5
■ Mixer Basics................................ 6
Quick Guide.......................................... 6
Making the Most of Your Mixer........... 8
Balanced, Unbalanced
—What’s the Difference?..............................8
Signal Levels and the Decibel..........................8
To EQ or Not to EQ..........................................9
Ambience.......................................................10
The Modulation Effects:
Phasing, Chorus, and Flanging ..................10
Compression..................................................10
■ Reference .................................. 11
Setup ................................................... 11
Front & Rear Panels........................... 12
Channel Control Section................................12
Digital Effects.................................................15
Master Control Section ..................................16
Digital Effect Program List (Only MG166CX).19
Jack List.........................................................19
Troubleshooting................................. 20
Specifications..................................... 75
Accessories
• Owner’s Manual
•AC power adaptor (PA-30)*
*May not be included depending on your particular area. Please
check with your Yamaha dealer.
Introduction
Thank you for your purchase of the Yamaha MG206C/MG166CX/MG166C mixing console. The
MG206C/MG166CX/MG166C feature input channels suitable for a wide range of usage environments.
And the MG166CX includes high-quality built-in digital effects that can provide some very serious
sound. The mixer combines ease of operation with support for multiple usage environments.
Please read through this manual carefully before beginning use, so that you will be able to take full
advantage of this mixer’s superlative features and enjoy trouble-free operation for years to come.
1
Be sure that the mixer’s power switch is in the
STANDBY position.
Use only the included power adaptor (PA-30) or
an equivalent recommended by Yamaha. Use of a
different adaptor may result in equipment dam-
age, overheating, or fire.
2
Connect the power adaptor to the AC ADAPTOR IN
connector (
q) on the rear of the mixer, and then
turn the fastening ring clockwise (
w) to secure the
connection.
3
Plug the power adaptor into a standard household
power outlet.
• Be sure to unplug the adaptor from the outlet
when not using the mixer, or when there are
lightning storms in the area.
•To avoid generating unwanted noise, make
sure there is 50 cm or more between the power
adaptor and the mixer.
Press the mixer’s power switch to the ON position.
When you are ready to turn the power off, press the
power switch to the STANDBY position.
Note that trace current continues to flow while the
switch is in the STANDBY position. If you do not plan
to use the mixer again for a long while, please be sure
to unplug the adaptor from the wall outlet.
Before Turning on the Mixer
Turning the Power On
CAUTION
q
w
CAUTION
CAUTION
Contents
MG206C/MG166CX/MG166C Owner’s Manual
Mixer Basics
6
Quick Guide
We begin by connecting a pair of speakers and generating some stereo output. Note that
operations and procedures will vary somewhat according to the input devices you are using.
Getting Sound to the Speakers
PAN/BAL switches
1, 4
GAIN controls
4
PEAK indicators
Equalizer
5 ON switches
4 PFL switches
5 ST switches
1, 7 Channel faders
4, 7
Level meter
3
PHANTOM switch
Microphones, instruments
2
Speakers
Power Amp
2
Headphones
2, 4
Monitor Speakers
1, 6, 7 STEREO OUT Master fader
MG206C
1, 3 POWER switch
Mixer Basics
Mixer Basics
Quick Guide
MG206C/MG166CX/MG166C Owner’s Manual
7
1
Be sure that your mixer is turned off
and that all level controls* are turned
all the way down.
* STEREO OUT Master fader, Channel faders, GAIN
controls, etc.
Set the equalizer and the PAN/BAL controls to
their ▼ positions.
2
Turn off any other external devices,
then connect microphones, instru-
ments, and speakers.
•For information on connecting external
devices see the Connection Example on page
11.
• Connect electric guitars and basses through
an intermediary device such as a direct box,
preamp, or amp simulator. Connecting these
instruments directly to the MG mixer may
result in degraded sound and noise.
3
To avoid damage to your speakers,
power up the devices in the following
order: Peripheral devices →→
→→
MG mixer
→→
→→
power amps (or powered speakers).
Reverse this order when turning
power off.
If you are using condenser microphones that
require phantom power, turn the MG mixer’s
phantom power switch on before turning on
the power to the power amp or powered
speakers. See page 17 for more detail.
4
Adjust the channel GAIN controls so
that the corresponding PEAK indica-
tors flash briefly on the highest peak
levels.
To use the level meter to get an accurate read-
ing of the incoming signal level, turn the chan-
nel PFL switch on. Adjust the GAIN controls so
that the level meter indication occasionally
rises above the “▼” (0) level.
Note that the PHONES jack outputs the pre-
fader signal from all channels on which the
PFL switch is ON so that those signals can be
monitored via the headphones.
5
Turn on the ON and ST switches for
each channel you are using.
6
Set the STEREO OUT Master fader to
the “0” position.
7
Set the Channel faders to create the
desired initial balance, then adjust the
overall volume using the STEREO
OUT Master fader.
•To use the level meter to view the level being
applied to the STEREO L/R buses, set the
PFL switch off ( ) and the MONITOR switch
to STEREO ( ).
• If the PEAK indicator lights frequently, lower
the Channel faders a little to avoid distortion.
NOTE
NOTE
CAUTION
NOTE
NOTE
MG206C/MG166CX/MG166C Owner’s Manual
Mixer Basics
8
Making the Most of Your Mixer
You’ve got yourself a mixer and now you’re ready to use it.
Just plug everything in, twiddle the controls, and away you go … right?
Well, if you’ve done this before you won’t have any problems, but if this is the first time you’ve
ever used a mixer you might want to read through this little tutorial and pick up a few basics
that will help you get better performance and make better mixes.
Balanced, Unbalanced—What’s the Difference?
In a word: “noise.” The whole point of balanced lines is noise rejection, and it’s something they’re very good at.
Any length of wire will act as an antenna to pick up the random electromagnetic radiation we’re constantly sur-
rounded by: radio and TV signals as well as spurious electromagnetic noise generated by power lines, motors,
electric appliances, computer monitors, and a variety of other sources. The longer the wire, the more noise it is
likely to pick up. That’s why balanced lines are the best choice for long cable runs. If your “studio” is basically con-
fined to your desktop and all connections are no more than a meter or two in length, then unbalanced lines are
fine—unless you’re surrounded by extremely high levels of electromagnetic noise. Another place balanced lines
are almost always used is in microphone cables. The reason for this is that the output signal from most micro-
phones is very small, so even a tiny amount of noise will be relatively large, and will be amplified to an alarming
degree in the mixer’s high-gain head amplifier.
Signal Levels and the Decibel
Let’s take a look at one of the most commonly used units in
audio: the decibel (dB). If the smallest sound that can be
heard by the human ear is given an arbitrary value of 1, then
the loudest sound that can be heard is approximately
1,000,000 (one million) times louder. That’s too many digits
to deal with for practical calculations, and so the more appro-
priate “decibel” (dB) unit was created for sound-related mea-
surements. In this system the difference between the softest
and loudest sounds that can be heard is 120 dB. This is a
non-linear scale, and a difference of 3 dB actually results in a
doubling or halving of the loudness.
You might encounter a number of different varieties of the
dB: dBu, dBV, dBM and others, but the dBu is the basic deci-
bel unit. In the case of dBu, “0 dBu” is specified as a signal
level of 0.775 volts. For example, if a microphone’s output
level is -40 dBu (0.00775 V), then to raise that level to 0 dBu
(0.775 V) in the mixer’s preamp stage requires that the signal
be amplified by 100 times.
A mixer may be required to handle signals at a wide range of
levels, and it is necessary match input and output levels as closely as possible. In most cases the “nominal” level
for a mixer’s input and outputs is marked on the panel or listed in the owner’s manual.
Hot (+)
Cold (–)
Ground
Source
Cable
Noise cancelled
Noise-free
signal
Phase
inversion
Receiving device
Phase
inversion
To summarize
Microphones Use balanced lines.
Short line-
level runs
Unbalanced lines are fine if
you’re in a relatively noise-
free environment.
Long line-
level runs
The ambient electromag-
netic noise level will be the
ultimate deciding factor, but
balanced is best.
Noise
Balanced noise cancellation
+ 20 dBu
0 dBu
0.775 V
-
20 dBu
-
40 dBu
-
60 dBu
The inputs and outputs on
home-use audio gear usually
have a nominal level of –7.8 dBu
(–10 dBV).
Most professional mixers,
power amplifiers, and other
types of equipment have inputs
and outputs with a nominal level
of +4 dBu.
Microphone signal levels vary
over a wide range depending on
the type of microphone and the
source. Average speech is
about –30 dBu, but the twitter-
ing of a bird might be lower than
–50 dBu while a solid bass
drum beat might produce a level
as high as 0 dBu.
Mixer Basics
Making the Most of Your Mixer
MG206C/MG166CX/MG166C Owner’s Manual
9
To EQ or Not to EQ
In general: less is better. There are many situations in which you’ll need to cut certain frequency ranges, but use
boost sparingly, and with caution. Proper use of EQ can eliminate interference between instruments in a mix and
give the overall sound better definition. Bad EQ—and most commonly bad boost—just sounds terrible.
Cut for a Cleaner Mix
For example: cymbals have a lot of energy in the mid and
low frequency ranges that you don’t really perceive as
musical sound, but which can interfere with the clarity of
other instruments in these ranges. You can basically turn
the low EQ on cymbal channels all the way down without
changing the way they sound in the mix. You’ll hear the dif-
ference, however, in the way the mix sounds more “spa-
cious,” and instruments in the lower ranges will have better
definition. Surprisingly enough, piano also has an incredi-
bly powerful low end that can benefit from a bit of low-fre-
quency roll-off to let other instruments—notably drums and
bass—do their jobs more effectively. Naturally you won’t
want to do this if the piano is playing solo.
The reverse applies to kick drums and bass guitars: you
can often roll off the high end to create more space in the
mix without compromising the character of the instruments.
You’ll have to use your ears, though, because each instru-
ment is different and sometimes you’ll want the “snap” of a
bass guitar, for example, to come through.
Boost with Caution
If you’re trying to create special or unusual effects,
go ahead and boost away as much as you like.
But if you’re just trying to achieve a good-sounding
mix, boost only in very small increments. A tiny
boost in the midrange can give vocals more pres-
ence, or a touch of high boost can give certain
instruments more “air.” Listen, and if things don’t
sound clear and clean try using cut to remove fre-
quencies that are cluttering up the mix rather than
trying to boost the mix into clarity.
One of the biggest problems with too much boost
is that it adds gain to the signal, increasing noise
and potentially overloading the subsequent cir-
cuitry.
Some Frequency Facts
The lowest and highest frequencies than can be heard by the human ear are generally considered to be around 20 Hz
and 20,000 Hz, respectively. Average conversation occurs in the range from about 300 Hz to about 3,000 Hz. The fre-
quency of a standard pitchfork used to tune guitars and other instruments is 440 Hz (this corresponds to the “A3” key
on a piano tuned to concert pitch). Double this frequency to 880 Hz and you have a pitch one octave higher (i.e. “A4”
on the piano keyboard). In the same way you can halve the frequency to 220 Hz to produce “A2” an octave lower.
20 50 100 200 500 1 k 2 k 5 k 10 k 20 k
(
Hz
)
The fundamental and harmonic frequency ranges of some
musical instruments.
Piano
Bass Drum
Snare Drum
Bass
Guitar
Trombone
Tr umpet
Cymba
l
Fundamental: The frequency that determines the basic
musical pitch.
Harmonics: Multiples of the fundamental frequency
that play a role in determining the timbre
of the instrument.
Frequency (Hz)
LOW Boost
LOW Flat
MID Boost
MID Flat
HIGH Boost
HIGH Flat
HIGH Cut
MID Cut
LOW Cut
Signal
Level (dB)
Making the Most of Your Mixer
MG206C/MG166CX/MG166C Owner’s Manual
Mixer Basics
10
Ambience
Your mixes can be further refined by adding ambi-
ence effects such as reverb or delay. The MG166CX’s
internal effects can be used to add reverb or delay to
individual channels in the same way as external
effects processors. (Refer to page 15).
Reverb and Delay Time
The optimum reverb time for a piece of music will
depend on the music’s tempo and density, but as a
general rule longer reverb times are good for ballads,
while shorter reverb times are more suited to up-
tempo tunes. Delay times can be adjusted to create a
wide variety of “grooves”. When adding delay to a
vocal, for example, try setting the delay time to dotted
eighth notes corresponding to the tune’s tempo.
Reverb Tone
Different reverb programs will have different “reverb
tone” due to differences in the reverb time of the high
or low frequencies. Too much reverb, particularly in
the high frequencies, can result in unnatural sound
and interfere with the high frequencies in other parts
of the mix. It’s always a good idea to choose a reverb
program that gives you the depth you want without
detracting from the clarity of the mix.
Reverb Level
It’s amazing how quickly your ears can lose perspec-
tive and fool you into believing that a totally washed-
out mix sounds perfectly fine. To avoid falling into this
trap start with reverb level all the way down, then
gradually bring the reverb into the mix until you can
just hear the difference. Any more than this normally
becomes a “special effect.”
The Modulation Effects:
Phasing, Chorus, and Flanging
All of these effects work on basically the same princi-
ple: a portion of the audio signal is “time-shifted” and
then mixed back with the direct signal. The amount of
time shift is controlled, or “modulated”, by an LFO
(Low-frequency Oscillator).
For phasing effects the shift is very small. The phase
difference between the modulated and direct signals
causes cancellation at some frequencies and rein-
forces the signal at others and this causes the shim-
mering sound we hear.
For chorus and flanging the signal is delayed by sev-
eral milliseconds, with the delay time modulated by
an LFO, and recombined with the direct signal. In
addition to the phasing effect described above, the
delay modulation causes a perceived pitch shift
which, when mixed with the direct signal, results in a
harmonically rich swirling or swishing sound.
The difference between chorus and flanging effects is
primarily in the amount of delay time and feedback
used—flanging uses longer delay times than chorus,
whereas chorus generally uses a more complex
delay structure. Chorus is most often used to thicken
the sound of an instrument, while flanging is usually
used as an outright “special effect” to produce other-
worldly sonic swoops.
Compression
One form of compression known as “limiting” can,
when properly used, produce a smooth, unified
sound with no excessive peaks or distortion. A com-
mon example of the use of compression is to “tame” a
vocal that has a wide dynamic range in order to
tighten up the mix. With the right amount of compres-
sion you’ll be able to clearly hear whispered pas-
sages while passionate shouts are still well balanced
in the mix. Compression can also be valuable on
bass guitar. Too much compression can be a cause of
feedback, however, so use it sparingly.
Most compressors require several critical parameters
to be set properly to achieve the desired sound. The
MG compressor makes achieving great sound much
easier: all you need to do is set a single “compres-
sion” control and all of the pertinent parameters are
automatically adjusted for you.
(Min)
(Max)
INPUT
OUTPUT
Reference
MG206C/MG166CX/MG166C Owner’s Manual
11
Setup
DI
Recorder
Synthesizer
CD Player
Microphone
Powered speakers
Powered monitor
speakers
Bass
Headphones
Guitar
Effect processor
Effect processor
(exciter)
Powered monitor
speakers
MG206C
Rear panel
Reference
MG206C/MG166CX/MG166C Owner’s Manual
Reference
12
Front & Rear Panels
Channel Control Section
1
2
1
5
6 6
C C
D D
F
G
H
F
G
H
I I
E E
0
A
9 9
7 7
8
0
A
BB
4
3
Channels
13/14 and 15/16
(Stereo)
Channels
1 to 8
(Monaural)
Channels
9 to 12
(Monaural)
● MG206C
Channels
17/18 and 19/20
(Stereo)
1
2
1
5
6
6
C
D
F
G
H
I
E
0
A
9 9
7
7
8
3
4
B
C
D
F
G
H
I
E
0
B
A
Channels
9/10 and 11/12
(Stereo)
Channels
1 to 6
(Monaural)
Channels
7 and 8
(Monaural)
Channels
13/14 and 15/16
(Stereo)
● MG166CX/MG166C
* A MG166C : EFFECT → AUX3
Reference
Front & Rear Panels
MG206C/MG166CX/MG166C Owner’s Manual
13
1 MIC Input jacks
These are balanced XLR-type microphone input jacks. (1:
Ground; 2: Hot; 3: Cold)
2 LINE Input Jacks (monaural channels)
These are balanced TRS phone-jack line inputs. (T: Hot; R:
Cold; S: Ground). You can connect either balanced or unbal-
anced phone plugs to these jacks.
3 LINE Input Jacks (stereo channels)
These are unbalanced phone-jack stereo line inputs.
4 LINE Input Jacks (stereo channels)
These are unbalanced stereo RCA pin jacks.
On channels that provide multiple input jack options
only one type of jack can be used at a time.
5 INSERT Jacks
These jacks can be used to insert an external signal-process-
ing device between the equalizer and fader of the corre-
sponding monaural input channel. The INSERT jacks are
ideal for connecting devices such as graphic equalizers,
compressors, or noise filters into the corresponding chan-
nels.
These are TRS (tip, ring, sleeve) phone jacks that
carry both the send and return signal (tip = send/out;
ring = return/in; sleeve = ground). Patching external
devices via an INSERT jack requires a special cable
such as illustrated below (insert cable sold sepa-
rately).
The signal output from the INSERT jacks is
reverse-phased. This should not be a problem
when connecting to an effect unit, but please be
aware of the possibility of phase conflict when
connecting to other types of device. A reversed-
phased signal may result in degraded sound
quality or even complete sound cancellation.
6 GAIN Control
Adjusts the input signal level. To get the best balance
between the S/N ratio and the dynamic range, adjust the gain
so that the PEAK indicator
9 lights only occasionally and
briefly on the highest input transients. The -60 to -16 scale is
the MIC input adjustment range. The -34 to +10 scale is the
LINE input adjustment range.
7 Switch (High-Pass Filter)
This switch toggles the HPF on or off. To turn the HPF on,
press the switch in ( ). The HPF cuts frequencies below
80 Hz (the HPF does not apply to the line inputs of stereo
input channels
3, 4).
8 COMP Control
Adjusts the amount of compression applied to the channel.
As the knob is turned to the right the compression ratio
increases while the output gain is automatically adjusted
accordingly. The result is smoother, more even dynamics
because louder signals are attenuated while the overall level
is boosted.
Avoid setting the compression too high, as the higher
average output level that results may lead to feed-
back.
9 PEAK indicator
The peak level of the post-EQ signal is detected, and the
PEAK indicator lights red when the level reaches 3 dB
below clipping.
For XLR-equipped stereo input channels, both the post-EQ
and post-mic-amp peak levels are detected, and the indicator
lights red if either of these levels reaches 3 dB below clip-
ping.
0 Equalizer (HIGH, MID and LOW)
This three-band equalizer adjusts the channel’s high, mid,
and low frequency bands. Setting the knob to the “▼” posi-
tion produces a flat response in the corresponding band.
Turning the knob to the right boosts the corresponding fre-
quency band, while turning to the left attenuates the band.
The monaural channels have MID frequency controls to
adjust the midrange frequency band.
The following table shows the EQ type, frequency, and max-
imum cut/boost for each of the three bands.
* The monaural channel MID frequency can be adjusted from
250 Hz to 5 kHz. The MID frequency is 2.5 kHz when the
MID frequency control is set at the center position.
NOTE
NOTE
To the INSERT I/O jack
To the input jack of the
external processor
Tip: OUT
Tip: IN
To the output jack of
the external processor
Sleeve (Ground)
Ring: IN
Tip: OUT
CAUTION
Band Type Frequency
Maximum
Cut/Boost
HIGH
Shelving 10 kHz
±15 dBMID Peaking 2.5 kHz*
LOW
Shelving 100 Hz
NOTE
Front & Rear Panels
MG206C/MG166CX/MG166C Owner’s Manual
Reference
14
A AUX, EFFECT Control
Adjusts the level of the signal sent from the channel to the
AUX and EFFECT buses. These knobs should generally be
set close to the “▼” position. These controls send either the
signal from immediately prior to the channel fader (pre-fader
signal) or the signal after the channel fader (post-fader sig-
nal) to the corresponding buses. The types of signals sent by
the AUX and EFFECT controls on each mixer model are as
follows:
• MG206C
AUX1: Pre-fader
AUX2, 3: Pre-fader/post-fader (determined by the AUX
PRE switch
B)
AUX4: Post-fader
• MG166CX
AUX1: Pre-fader
AUX2: Pre-fader/post-fader (determined by the AUX
PRE switch
B)
EFFECT: Post-fader
• MG166C
AUX1: Pre-fader
AUX2: Pre-fader/post-fader (determines by the AUX
PRE switch
B)
AUX3: Post-fader
•To send the signal to the STEREO bus engage the
ON switch ( ).
• On stereo channels, the L (odd) and R (even) input
signals are mixed and sent to the AUX and
EFFECT buses.
B AUX PRE Switch
Selects whether the pre-fader or the post-fader signal is fed
to the AUX buses. If the switch is on ( ), the mixer sends
the pre-fader signal to the AUX buses, so that AUX outputs
are not affected by the channel fader
I. If the switch is off
() the mixer sends the post-fader signal to the AUX
buses.
C PAN Control
PAN/BAL Control
BAL Control
The PAN control determines the stereo positioning of the
channel signal on the GROUP 1/2 and GROUP 3/4 buses or
on the STEREO L/R bus. The BAL control knob sets the
balance between left and right channels. Signals input to the
L input (odd channel) go to the GROUP 1 or 3 buses or to
the STEREO L bus; signals input to the R input (even chan-
nel) go to the GROUP 2 or 4 buses or the STEREO R bus.
On channels where this knob provides both PAN and
BAL control, the knob operates as a PAN control
when input is received via the MIC jack or L (MONO)
input only, and as a BAL control when input is
received via both L and R inputs.
D ON Switch
Turn this switch on to send the signal to the buses. The
switch lights orange when on.
E PFL (Pre-Fader Listen) Switch
This switch lets you monitor the channel’s pre-fader signal.
Press the switch in ( ) so that it lights to turn it on. When
the switch is on the channel pre-fader signal is output to the
PHONES and MONITOR OUT jacks for monitoring.
F 1-2 Switch
This switch assigns the channel’s signal to the GROUP 1/2
bus.
To send the signal to the GROUP 1/2 bus turn the
ON switch on ( ).
G 3-4 Switch
This switch assigns the channel’s signal to the GROUP 3/4
bus.
To send the signal to the GROUP 3/4 bus turn the
ON switch on ( ).
H ST Switch
This switch assigns the channel’s signal to the STEREO L/R
bus.
To send the signal to the STEREO bus turn the ON
switch on ( ).
I Channel Fader
Adjusts the level of the channel signal. Use these faders to
adjust the balance between the various channels.
Set the fader sliders for unused channels all the way
down to minimize noise.
NOTE
NOTE
NOTE
NOTE
NOTE
NOTE
Reference
Front & Rear Panels
MG206C/MG166CX/MG166C Owner’s Manual
15
1 FOOT SWITCH Jack
A Yamaha FC5 foot switch (sold separately) can be connected to this jack
and used to toggle the digital effects ON and OFF.
2 PROGRAM Dial
Selects one of the 16 internal effects. See page 19 for details about the
internal effects.
3 PARAMETER Control
Adjusts the parameter (depth, speed, etc.) for the selected effect. The last
value used with each effect type is saved.
When you change to a different effect type, the mixer automatically
restores the value that was previously used with that type (regard-
less of the current position of the PARAMETER knob).
These parameter values are reset when the power is turned off.
4 AUX Control
Adjusts the level of the signal sent from the internal digital effect unit to
the AUX buses.
The signal level sent to the AUX buses is not affected by the
EFFECT RTN fader.
5 ON Switch
Switches the internal effect on or off. The internal effect is applied only if
this switch is turned on. The switch lights orange when on.
An optional Yamaha FC5 foot switch (sold separately) can be used to tog-
gle the digital effects ON and OFF.
The ON switch lights and the internal effect unit is active when the
power is initially turned on.
6 PFL Switch
Turn this switch on to send the effect signal to the PFL bus.
7 1-2 Switch
This switch assigns the effect signal to the GROUP 1/2 bus.
8 3-4 Switch
This switch assigns the effect signal to the GROUP 3/4 bus.
9 ST Switch
This switch assigns the effect signal to the STEREO L/R bus.
0 EFFECT RTN Fader
Adjusts the signal level sent from the internal digital effect unit to the STE-
REO bus.
NOTE
NOTE
NOTE
Digital Effects * Only the MG166CX has digital effects.
4
3
5
0
2
6
1
7
8
9
Front & Rear Panels
MG206C/MG166CX/MG166C Owner’s Manual
Reference
16
Master Control Section
0
A
I
G
D
E
C
9
B
6
8
7
54321
H
F
0
A
I
G
E
9
B
H
F
6
8
4
1
3
7
25
D
C
Rear panel
● MG206C ● MG166CX/MG166C
* 1, C MG166C : EFFECT → AUX3
Reference
Front & Rear Panels
MG206C/MG166CX/MG166C Owner’s Manual
17
1 SEND Jacks (AUX, EFFECT)
These impedance balanced* TRS phone jacks output the sig-
nals from the AUX/EFFECT buses. The pre-fader send option
should be selected if you are connecting to a monitor system,
while the post-fader send option is the best choice when con-
necting to external signal processors (e.g. effects units).
See “AUX, EFFECT Control” on page 14 for information on
the types of signals sent by the AUX and EFFECT controls
on each mixer model.
2 GROUP OUT (1 to 4) Jacks
These impedance-balanced* TRS phone jacks output the
GROUP 1/2 and 3/4 signals. Use these jacks to connect to
the input jacks of an multi-track recorder, external mixer, or
other such device.
3 REC OUT (L, R) Jacks
These RCA pin jacks can be connected to an external
recorder such as an MD recorder in order to record the same
signal that is being output via the STEREO OUT jacks.
The mixer’s STEREO OUT Master fader has no
affect on the signal output via these jacks.
Be sure to make appropriate level adjustments at the
recording device.
4 2TR IN Jacks
These RCA pin jacks input a stereo sound source.
Use these jacks when you want to connect a CD player
directly to the mixer.
Select where you want to send the signal using the
2TR IN switch, and adjust the signal level using the
2TR IN control in the Master Control section.
5 RETURN L (MONO), R Jacks
These are unbalanced phone-jack type line inputs.
The signal received by these jacks can be sent to the STE-
REO L/R bus as well as the AUX1 and AUX2 buses. When a
stereo signal is returned a mono mix of the signal is sent to
the AUX1 and AUX2 buses. These jacks are typically used to
receive the signal returned from an external effect device
(reverb, delay, etc.).
• These jacks can also be used as an auxiliary ste-
reo input.
• If you connect to the L (MONO) jack only, the mixer
will recognize the signal as monaural and will send
the identical signal to both the L and R jacks.
6 STEREO OUT (L, R) Jacks
These jacks deliver the mixer’s stereo output. You use these
jacks, for example, to connect to the power amplifier driving
your main speakers. You can also connect these jacks to a
recording device when you wish to record mixer’s stereo
output while using the STEREO OUT Master fader
I for
level control.
• XLR jacks
XLR-type balanced output jacks.
• LINE jacks
TRS phone-type balanced output jacks.
7 MONITOR OUT jacks
These are impedance-balanced* TRS phone-type output
jacks.
The signal output by these jacks is determined by the
MONITOR switch, the 2TR IN switch, and the PFL
switches on the input channels.
8 PHONES Jack
Connect a pair of headphones to this TRS phone-type output
jack. The PHONES jack outputs the same signal as the
MONITOR OUT jacks.
9 PHANTOM +48 V Switch
This switch toggles phantom power on and off. When the
switch is on the mixer supplies +48V phantom power to all
channels that have XLR mic input jacks. Turn this switch on
when using one or more phantom-powered condenser micro-
phones.
When this switch is on the mixer supplies DC +48 V
power to pins 2 and 3 of all XLR-type MIC INPUT
jacks.
• Be sure to leave this switch off if you do not
need phantom power.
• When turning the switch on, be sure that only
condenser microphones are connected to the
XLR input jacks. Devices other than condenser
mics may be damaged if connected to the
phantom power supply. Note, however, that the
switch may be left on when connecting to bal-
anced dynamic microphones.
•To prevent damage to speakers, be sure to turn
off power amplifiers (or powered speakers)
before turning this switch on or off. We also
recommend that you turn all output controls
(STEREO OUT Master fader, GROUP 1-2 fader,
GROUP 3-4 fader, etc.) to their minimum set-
tings before operating the switch to avoid the
risk of loud noises that could cause hearing
loss or device damage.
0 POWER Indicator
This indicator lights when the mixer’s power is ON.
A Level Meter
This LED meter displays the level of the signal selected by
the MONITOR switch
D, 2TR IN switch E and PFL
switch. The “0” segment corresponds to the nominal output
level. The PEAK indicator lights red when the output
reaches the clipping level.
B RETURN
•AUX1, AUX2 Control
Adjusts the level at which the L/R signal received at the
RETURN jacks (L (MONO) and R) is sent to the AUX1 and
AUX2 buses.
• STEREO Control
Adjusts the level at which the signal received at the RETURN
jacks (L (MONO) and R) is sent to the STEREO L/R bus.
• If you supply a signal to the RETURN L (MONO)
jack only, the mixer sends the same signal to both
the L and R STEREO buses.
• (MG206C) Signals input via the RETURN1 jacks
are adjusted using the RETURN1 AUX1, AUX2 and
the STEREO controls, and signals input via the
RETURN2 jacks are adjusted using the RETURN2
AUX1, AUX2 and the STEREO controls.
NOTE
NOTE
NOTE
NOTE
NOTE
CAUTION
NOTE
* impedance balanced
Since the hot and cold terminals of impedance balanced output
jacks have the same impedance, these output jacks are less
affected by induced noise.
Front & Rear Panels
MG206C/MG166CX/MG166C Owner’s Manual
Reference
18
C Master SEND Controls (AUX, EFFECT)
Adjusts the signal level sent to the SEND (AUX, EFFECT)
jacks.
If you are using the MG166CX, the Master SEND
control (EFFECT) does not affect the level of the sig-
nal sent from the EFFECT bus to the internal digital
effect processor.
D MONITOR/PHONES
• MONITOR switches
These switches select the signal sent to the MONITOR OUT
jacks, PHONES jack and the level meter from STEREO L/R
bus, GROUP 1/2 bus or GROUP 3/4 bus.
STEREO L/R bus: STEREO ( )
GROUP 1/2 bus: GROUP ( ), 1-2 ( )
GROUP 3/4 bus: GROUP ( ), 3-4 ( )
• MONITOR Control
Controls the level of the signal output to the PHONES jack
and the MONITOR OUT jacks.
E 2TR IN
• 2TR IN Switch
If this switch is set to TO MONITOR ( ), the signals input
via the 2TR IN jacks are sent to the MONITOR OUT jacks,
the PHONES jack, and the level meter. If it is set to TO STE-
REO ( ), the signals are sent to the STEREO L/R bus.
• 2TR IN Control
Adjusts the level of the signal sent from the 2TR IN jacks.
The following illustration shows how the switch settings cor-
respond to the signal selection.
*: When overdubbing, you can adjust the levels of the mon-
itor playback signal and the signal being recorded separately.
MONITOR MIX Signal Flow
If the input channel PFL switch is on ( ), then only
the PFL output from that channel is sent to the MON-
ITOR OUT jacks, PHONES jack, and level meter.
F GROUP 1-2 Fader
Adjusts the signal level sent to the GROUP OUT 1/2 jacks.
G GROUP 3-4 Fader
Adjust the signal level to the GROUP OUT 3/ 4 jacks.
H ST Switch
If this switch is on, the signals are sent to the STEREO L/R
bus via the GROUP 1-2 fader or GROUP 3-4 fader. The
GROUP 1 and 3 signals go to STEREO L and the GROUP 2
and 4 signals go to STEREO R.
I STEREO OUT Master Fader
Adjusts the signal level sent to the STEREO OUT jacks.
Switches
Signals output via the
MONITOR/PHONES
jacks
PFL
MONITOR/
PHONES
2TR IN
ON
— — PFL
OFF
STEREO
TO STEREO
STEREO (+ 2TR IN)
TO MONITOR
STEREO + 2TR IN
*
GROUP
1-2
TO STEREO
GROUP 1-2
TO MONITOR
GROUP 1-2 (+ 2TR IN)
3-4
TO STEREO
GROUP 3-4
TO MONITOR
GROUP 3-4 (+ 2TR IN)
NOTE
Playback
signal
Recording
signal
2TR IN
2TR IN control
STEREO OUT Master fader
MONITOR/PHONES controls
STEREO
bus
REC OUT
jacks
MONITOR
OUT/PHONES
jacks
NOTE
Reference
Front & Rear Panels
MG206C/MG166CX/MG166C Owner’s Manual
19
Digital Effect Program List (Only MG166CX)
* “LFO” stands for Low Frequency Oscillator. An LFO is normally used to modulate another signal, determining the modulation speed and
waveform shape.
Jack List
* These jacks will also accept connection to phone plugs. If you use monaural plugs, the connection will be unbalanced.
No Program Parameter Description
1 REVERB HALL 1 REVERB TIME
Reverb simulating a large space such as a concert hall.
2 REVERB HALL 2 REVERB TIME
3 REVERB ROOM 1 REVERB TIME
Reverb simulating the acoustics of a small space (room).
4 REVERB ROOM 2 REVERB TIME
5 REVERB STAGE 1 REVERB TIME
Reverb simulating a large stage.
6 REVERB STAGE 2 REVERB TIME
7 REVERB PLATE REVERB TIME Simulation of a metal-plate reverb unit, producing a more hard-edged sound.
8DRUM AMBIENCE REVERB TIME A short reverb that is ideal for use with kick drum.
9 KARAOKE ECHO DELAY TIME Echo designed for karaoke (sing-along) applications.
10 VOCAL ECHO DELAY TIME Echo suitable for vocals.
11 CHORUS 1 LFO Frequency Creates a thick sound by modulating the delay time.
The PARAMETER control adjusts the frequency of the LFO* that modulates the
delay time.
12 CHORUS 2 LFO Frequency
13 FLANGER LFO Frequency
A sweeping pitched effect.
The PARAMETER control adjusts the frequency of the LFO* that modulates the
delay time.
14 PHASER LFO Frequency
Phase modulation produces a cyclical phasing effect.
The PARAMETER control adjusts the frequency of the LFO* that modulates the
delay time.
15 AUTO WAH LFO Frequency
A wah-wah effect with cyclical filter modulation.
The PARAMETER control adjusts the frequency of the LFO* that modulates the
delay time.
16 DISTORTION DRIVE Adds a sharp-edged distortion to the sound.
Input and Output Jacks Polarities Configurations
MIC INPUT, STEREO OUT
Pin 1: Ground
Pin 2: Hot (+)
Pin 3: Cold (–)
LINE INPUT (monaural channels)
GROUP OUT, STEREO OUT,
MONITOR OUT, AUX SEND,
EFFECT SEND (Only MG166CX)*
Tip: Hot (+)
Ring: Cold (–)
Sleeve: Ground
INSERT
Tip: Output
Ring: Input
Sleeve: Ground
PHONES
Tip: L
Ring: R
Sleeve: Ground
RETURN
LINE INPUT (stereo channels)
Tip: Hot
Sleeve: Ground
OUTPUTINPUT
XLR Jack
TipSleeve
Ring
TRS Phone Jack
TipSleeve
Phone Jack
MG206C/MG166CX/MG166C Owner’s Manual
Reference
20
Troubleshooting
Power doesn’t come on.
❑ Is the supplied power adaptor properly plugged into an appropriate AC wall
outlet?
❑ Is the supplied power adaptor properly plugged into the mixer?
No sound.
❑ Are microphones, external devices, and speakers connected correctly?
❑ Are the ON switch and ST switch of the channels you are using turned ON?
❑ Are the channel GAIN controls, Channel fader, STEREO OUT Master fader
and GROUP 1-2/3-4 fader set to appropriate levels?
❑ Are the MONITOR switch and 2TR IN switch set properly?
❑ Are your speaker cables connected properly, or are they shorted?
❑ If the above checks do not identify the problem, call Yamaha for service.
(Refer to the page 71 for a list of service centers.)
Sound is faint, distorted, or
noisy.
❑ Are the channel GAIN controls, Channel fader, STEREO OUT Master fader
and GROUP 1-2/3-4 fader set to appropriate levels?
❑ Are two different instruments connected to the XLR-type and phone jacks, or
to the phone and RCA pin jacks on one channel? Please connect to only one
of these jacks on each channel.
❑ Is the input signal from the connected device set to an appropriate level?
❑ Are you applying the effects at an appropriate level?
❑ Are microphones connected to the MIC input jacks?
❑ If you are using condenser microphones, is the PHANTOM +48 V switch
turned ON?
No effect is applied.
(If you are using MG166CX)
❑ Check that the EFFECT control on each channel is correctly adjusted.
❑ Be sure that the internal effect unit’s ON switch is turned ON.
❑ Be sure that the EFFECT PARAMETER control and EFFECT RTN fader are
correctly adjusted.
I want spoken words to be
heard more clearly.
❑ Be sure that the switches are ON.
❑ Adjust the equalizers (HIGH, MID and LOW) on each channel.
I want to output a monitor
signal through speakers.
❑ Connect a powered speaker to the AUX 1, 2 or 3 jack (MG206C), or to the
AUX1 or 2 jack (MG166CX/MG166C) and turn the PRE switch on each chan-
nel on. Then adjust the output signal by using the AUX controls on each chan-
nel and the Master SEND control.
The level meter doesn’t
show the output signal
level.
❑ Are the PFL switches for the channels that you are not using turned on?
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
Stránka se načítá ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29

Yamaha MG166CX Návod k obsluze

Yamaha
Značka
Yamaha
Modelka
MG166CX
Kategorie
Audio mixéry
Typ
Návod k obsluze
Stáhnout PDF
zpráva

v jiných jazycích

Související papíry