Yamaha CZR10 Návod k obsluze

Značka: Yamaha

Modelka: CZR10

Kategorie: Audio zesilovače

Typ: Návod k obsluze

Tato příručka je také vhodná pro

CZR12
CZR15

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manual do Proprietário

Manuale di istruzioni

Руководство пользователя

SPEAKER SYSTEM

LOUDSPEAKER

2 CZR series Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other

hazards. These precautions include, but are not limited

to, the following:

If you notice any abnormality

• If any of the following problems occur, immediately turn off

the power of the amplifier.

- Unusual smells or smoke are emitted.

- Some object, or water has been dropped into the product.

- There is a sudden loss of sound during use of the product.

- Cracks or other visible damage appear on the product.

Then have the product inspected or repaired by qualified

Yamaha service personnel.

Do not open

• This product contains no user-serviceable parts. Do not

attempt to disassemble the internal parts or modify them in

any way.

Water warning/Fire warning

• Do not expose the product to rain, use it near water or in

damp or wet conditions, or place on it any containers (such

as vases, bottles or glasses) containing liquids which might

spill into any openings.

• Do not place any burning items or open flames near the

product, since they may cause a fire.

Hearing loss

• When turning on the AC power in your audio system, always

turn on the power amplifier LAST, to avoid hearing loss and

speaker damage. When turning the power off, the power

amplifier should be turned off FIRST for the same reason.

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or others,

or damage to the product or other property. These

precautions include, but are not limited to, the following:

Location and connection

• Do not place the product in an unstable position where it

might accidentally fall over and cause injuries.

• Keep the device out of reach of children. This product is not

suitable for use in locations where children are likely to be

present.

• Do not place the product in a location where it may come into

contact with corrosive gases or salt air. Doing so may result in

malfunction.

• Before moving the product, remove all connected cables.

• When transporting or moving the product, always use two or

more people. Attempting to lift the product by yourself may

damage your back, result in other injury, or cause damage to

the product itself.

• Do not use the speaker’s handles for suspended installation.

Doing so can result in damage or injury.

• Do not hold the bottom of the product when transporting or

moving it. In doing so, you may pinch your hands under the

product, and result in injury.

• Do not press the rear panel of the product against the wall.

Doing so may cause the plug to come in contact with the wall

and detach from the cable, resulting in short circuiting,

malfunction, or even fire.

• Always consult qualified Yamaha service personnel if the

product installation requires construction work, and make

sure to observe the following precautions.

- Choose mounting hardware and an installation location that

can support the weight of the product.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the product.

- Inspect the product periodically.

• Use only speaker cables. Use of other types of cables may

result in fire.

Handling caution

• When choosing a power amplifier for use with this product,

make sure that the output power of the amplifier is lower than

the power capacity of this product. If the output power is

higher than the power capacity, malfunction or fire may occur.

• Do not input excessively loud signals that may result in

clipping in the amplifier or cause the following:

- Feedback, when using a microphone

- Continuous and extremely loud sound from a musical

instrument, etc.

- Continuous and excessively loud distorted sound

- Noise caused by plugging/unplugging the cable while the

amplifier is turned on

Even if the output power of the amplifier is lower than the

power capacity of this product (program), damage to the

product, malfunction or fire may occur.

• Do not operate the product if the sound is distorting.

Prolonged use in this condition could cause overheating and

result in fire.

Yamaha cannot be held responsible for damage caused by

improper use or modifications to the product.

PA_en_9

CZR series Owner’s Manual 3

NOTICE

To avoid the possibility of malfunction/damage to the product,

or damage to other property, follow the notices below.

 Handling and maintenance

• Do not expose the product to excessive dust or vibration,

or extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disfiguration, unstable operation, or

damage to the internal components.

• Do not place the speaker face down with the grille

attached, as deformation of the grille may result.

• When placing the speaker face down, always place it on a

flat surface.

• Do not touch the speaker driver unit.

• Be sure to observe the amplifier’s rated load impedance

(see page 7), particularly when connecting speakers in

parallel. Connecting an impedance load outside the ampli-

fier's rated range can damage the amplifier.

• Protection Circuit

This speaker system has an internal protection circuit that

shuts off the speaker unit when an excessive input signal is

applied. If the speaker unit emits no sound, reduce the vol-

ume level of the amplifier immediately. The sound will

return automatically in several seconds.

• Air blowing out of the bass reflex ports is normal, and often

occurs when the speaker is handling program material

with heavy bass content.

• During extreme changes in temperature or humidity, con-

densation may occur and water may collect on the surface

of the product. If water is left, the wooden parts may

absorb the water and be damaged. Make sure to wipe any

water off immediately with a soft cloth.

 Connectors

• Use only Neutrik NL4 plugs for connecting speakON con-

nectors.

Information

 About this manual

• The illustrations as shown in this manual are for instruc-

tional purposes only.

• The company names and product names in this manual

are the trademarks or registered trademarks of their

respective companies.

 About disposal

• This product contains recyclable components. When dis-

posing of this product, please contact the appropriate

local authorities.

4 CZR series Owner’s Manual

(weee_eu_en_02)

Information for users on collection and disposal of old equipment:

This symbol on the products, packaging, and/or accompanying documents means that used electrical and elec-

tronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential nega-

tive effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your

waste disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for fur

ther informa-

tion.

Information on Disposal in other Countries outside the European Union:

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of disposal.

CZR series Owner’s Manual 5

Introduction

Thank you for purchasing the Yamaha CZR15, CZR12, CZR10 LOUDSPEAKER (hereinafter referred to as

“CZR”). This product is a speaker designed for live performance, sound reinforcement and fixed installa-

tion sound system applications. This manual explains how to install, set up, and configure the connec-

tions for the installers, constructors, or general users familiar with speakers. Please read this manual

thoroughly before you begin using this product to get the most out of the product. After reading this man-

ual, please keep it available for future reference.

• The example illustrations used in this manual are taken from the CZR12, if not otherwise specified.

Contents

PRECAUTIONS ..................................................................... 2

Introduction ........................................................................... 5

Main Features........................................................................ 5

Included Accessories............................................................ 5

Optional Accessories (sold separately) ................................ 5

Functions............................................................................... 6

Connection ............................................................................ 7

Selection and Settings of Processors and Amplifiers............8

Basic Setting Example...........................................................8

Rotatable Horn.......................................................................9

Switching Between Passive and Bi-amp Mode...................10

Installation Examples...........................................................11

Troubleshooting ...................................................................13

Specifications (English only) .............................................100

Main Features

• The CZR series has three different models, depending on the woofer size: CZR15 (15-inch), CZR12 (12-inch) and CZR10 (10-

inch).

• The LF (low-frequency) unit features an aluminum die-cast frame and a 3-inch voice coil for high durability in audio reproduc-

tion. It uses a lightweight and powerful neodymium magnet that achieves band extension to even lower frequencies and

reproduction capability that adds punch and power to the bass.

• The HF (high-frequency) unit features a titanium diaphragm, 2-inch voice coil, and neodymium magnet. It is paired with a fixed

directional horn designed specifically for each model, for sparkling highs and superior directional characteristics.

• The specially designed enclosure features lightweight and strong plywood with a scratch-resistant rigid polyurea coating for

improved portability and durability.

• A variety of installation methods are possible, including two angle adjustments for use on a stand, use as a floor monitor, sev-

eral rigging points, and 90-degree rotation of the horn.

• The speaker can be changed to a Bi-amp configuration, to maximize the performance of each unit and further optimize the

reproduction characteristics.

Included Accessories

Owner’s Manual (this book)

Optional Accessories (sold separately)

U-bracket (UB-DZR series) Speaker cover (SPCVR series)

CZR15 UB-DZR15H, UB-DZR15V SPCVR-DZR15

CZR12 UB-DZR12H, UB-DZR12V SPCVR-DZR12

CZR10 UB-DZR10H, UB-DZR10V SPCVR-DZR10

6 CZR series Owner’s Manual

Functions

q Tiltable pole socket

This mount has two pole sockets. You can choose the

angle of the CZR unit so that the speaker is positioned

horizontal to the floor or tilting down toward the floor by 7

degrees. These sockets are compatible with commercially

available speaker stands and speaker poles of 35 mm

diameter.

we [INPUT/PARALLEL] jacks

These are speakON jacks (Neutrik NL4) for connection to

a power amplifier using a speaker cable. The factory set-

ting is in the Passive mode. When using in the Passive

mode, input the signals to the 1+/1– contacts of the

[INPUT/PARALLEL] jack. w and e are connected in par-

allel.

r Screw holes for U-bracket

For installing with separately sold U-brackets.

t Screw holes for eye bolts

For installing the CZR using eye bolts. The screw holes for

eye bolts go through the cabinet wall.

Front Rear

Bottom

FRONT

7°

0°

7°

Pole socket

speakON plug

Insert all the way inside

and turn to lock

CZR series Owner’s Manual 7

Connection

Wiring

Wire the plugs as shown below. Make sure to use cables specially designed for speakers. When the CZR itself is used in the

Passive mode, wiring to the 2+ and 2– contacts is unnecessary. When the CZR is used in the Bi-amp mode, or when the signals

are sent together with the signal from a subwoofer over a single cable (see “Basic Setting Example” on page 8), make sure to

also wire to the 2+ and 2– contacts.

Parallel Connection of Speakers

[INPUT/PARALLEL] jacks are connected inside in parallel. The first CZR can receive the signal from a power amplifier (hereinaf-

ter, “amplifier”) by one of the [INPUT/PARALLEL] jacks, and route the signal to the second CZR from the rest of [INPUT/PARAL-

LEL] jacks.

When connecting CZR units in parallel, be sure to check the load impedance that the amplifier can drive with. The nominal

impedance of one CZR is eight ohms, and the total impedance of two parallel CZR units is four ohms. In this case, the amplifier

must be able to drive a speaker less than four ohm load impedance.

 Invalid connection

NOTICE

NEVER connect multiple signals from the amplifier to the [INPUT/PARALLEL] jacks simultaneously. This creates a very dangerous

short circuit, possibly resulting in amplifier malfunction.

Passive

(2–: Unused)

Bi-amp

(2+: Unused)

1+:

1–:

1+: LF+

1–: LF–

2+: HF+

2–: HF–

Amplifier

From

amplifier

To next CZR

First CZR

(impedance: 8 Ω)

Second CZR

(impedance: 8 Ω)

Parallel connection (total impedance: 4 Ω)

Amplifier

B channel

A channel

CZR

8 CZR series Owner’s Manual

Selection and Settings of Processors and Amplifiers

In order to take full advantage of the CZR performance, make sure to adjust the crossover and equalizer (EQ) using

a processor/DSP built-in amplifier.

When selecting an amplifier, the amplifier should have a similar program (PGM) wattage rating to the speaker. For

example, since the PGM rating of the CZR12 is 800W, an amplifier of 640W to 1000W (0.8 to 1.25 times that of

800W) should be selected. However, when a speaker can be protected properly by a limiter, amplifiers with more

power can be used together.

Visit the CZR product page of the Yamaha Pro Audio global website for details on the recommended models of pro-

cessors and amplifiers, and EQ settings.

Basic Setting Example

 This system is connected by two independent cables from a 2-channel amplifier to a CZR and a

subwoofer.

 This system is connected by a single cable from the outputs of a 2-channel amplifier, using the

output jack on the CXS series.

The output jack of the CXS series (subwoofers) receives the signals via 2+/2– of the [INPUT/PARALELL] jack and routes

them to 1+/1– for output. Using the output jack of the CXS along with a 4-pole speakON cable, you can connect an amplifier

to the CXS with a single cable. For details, please refer to the relevant CXS series manual.

2-channel amplifier

1+/1–: SUBWOOFER

1+/1–: FULL RANGE

CXS series

(subwoofer)

CZR

From

amplifier

CXS series

(subwoofer)

2+/2–: FULL RANGE

CZR

2-channel amplifier

1+/1–: SUBWOOFER

To CZ R

OUTPUT

Routes the signals received via

2+/2– to 1+/1– for output.

1+/1–: FULL RANGE

From

amplifier

4-pole speakON

cable

CZR series Owner’s Manual 9

Rotatable Horn

When shipped from the factory, the directivity of CZR in a vertical orientation is the setting which makes the sound

expand in a horizontal direction, and inhibits or narrows the sound in a vertical direction. We recommend changing

the directivity by rotating the horn when you want to install CZR horizontally or when you want to use them as a floor

monitor and broaden the directivity.

1. Using a 2.5 mm hexagonal wrench, remove all fixing screws (CZR10: six total) on the grille, and remove the grille from the

speaker.

2. Using a No. 2 Phillips head screwdriver, remove all screws installed on the horn and pull the horn out from the speaker.

3. Rotate the horn 90 degrees, and re-install the horn to the speaker, reversing the steps above.

• Make sure not to push the screws too strongly with the Phillips head screwdriver. This may cause the nuts inside the cabinet to fall off.

• If the horn cannot smoothly be pulled out, hook the notches using a flat-bladed screwdriver, and pull out.

NOTE

Screws (eight total)

Notch

Vertical

Rotate 90°

Horizontal

10 CZR series Owner’s Manual

Switching Between Passive and Bi-amp Mode

The factory setting for CZR internal wiring is the Passive mode. However, you can change the setting to the Bi-amp

mode. When driving in the Bi-amp mode, you must use an external crossover processor and the output from a 2-

channel amplifier. By driving in the Bi-amp mode, protection can be set separately for the LF and HF, and precise set-

tings can be made for crossover frequency and time alignment between the LF and HF. This optimizes the perfor-

mance capacity of each unit and increases the limit capability.

1. Using a M5 Phillips head screwdriver, remove all fixing screws on the rear panel, and remove the rear panel.

2. Disconnect the input and output cable connectors from the [PASSIVE IN]/[PASSIVE OUT] connectors on the network base,

and connect them to [BI-AMP IN]/[BI-AMP OUT] connectors respectively.

3. Re-install the rear panel to the speaker, reversing the steps above. (The base shown below is of the CZR10.)

• When removing the screws, make sure not to push the screws strongly. This may cause the nuts inside the cabinet to fall off.

• If the rear panel cannot smoothly be removed, hook the notches using a flat-bladed screwdriver, and pull out.

After changing the mode, we recommend marking the appropriate blank on the rear panel list to indicate the current state.

NOTE

Screws (six total)

Notch

PASSIVE IN

PASSIVE OUT

BI-AMP

OUT

BI-AMP

PASSIVE IN

PASSIVE OUT

BI-AMP

OUT

BI-AMP

Passive Bi-amp

To speaker units

From [INPUT/PARALLEL] jack From [INPUT/PARALLEL] jack

To speaker units

NOTE

CZR series Owner’s Manual 11

Installation Examples

Suspended Installation Using Eye Bolts



Suspension angle

Make sure to use eye bolts within a range of 0 to 45 degrees from a right angle.

 Suspended Installation Example

CAUTION

• Before doing any installation or construction work, consult with your Yamaha dealer.

• The installation should be checked thoroughly at regular intervals. Some fittings may deteriorate over extended periods of

time due to wear and/or corrosion.

• When choosing the installation location, suspension wire and mounting hardware, make sure all are strong enough to

support the weight of the speaker.

• Make sure to take precautionary measures using wires to prevent the speaker from falling down in the event of an installa-

tion failure.

• When installing the wire to the wall, install it higher than the wire’s attachment point on the speaker, with as little slack as

possible. If the wire is too long, and the speaker happens to fall, the wire may snap as a result of too much strain.

• Make sure to use eye bolts according to the standards and safety regulations in your area.

Yamaha cannot be held responsible for damage or injury caused by insufficient strength of the support structure or

improper installation.

Attach commercially-available long eye bolts (30–50 mm in

length) to the screw holes for the eye bolts (t on page 6).

The screw diameter for CZR15 and CZR12 is M10, and the

screw diameters for CZR10 are M10 and M8. Keep in mind

that you will need two or more rigging points.

 Securing the eye bolts

Insert the eye bolts through the washers when attaching

them.

• The screw holes for eye bolts go through the cabinet wall.

• When using eye bolts, remove the flat-head screws tightened at

the time of factory shipment. When not using eye bolts, tighten

the flat-head screws in order to prevent air leaks.

NOTE

Apply thread-

locking fluid

to the eye bolt

Bottom

0°

45°

Max. 45°

M10 eye bolt

Pullback point

Side

Max. 45°

Rear

12 CZR series Owner’s Manual

Installation Examples

 Incorrect examples for suspended installation

Do not suspend the eye bolts as shown in the illustrations below.

Installation Using a Dedicated U-bracket

By using the separately sold Yamaha UB-DZR series U-bracket, you can expand the installation possibilities of the CZR. For

instructions on installing the U-bracket, refer to the corresponding manual for the UB-DZR series.

 Examples

The UB-DZR series can be used together with separately sold optional brackets, such as the Yamaha BBS251 Baton Bracket.

More than

45°

More than

45°

More than 45°

from a right angle

Only one

suspension point

ProhibitedProhibited

NOTE

CZR series Owner’s Manual 13

Troubleshooting

If any specific problem should persist, contact your Yamaha dealer.

Symptom Possible causes Possible solution

No sound. The cable is not connected properly.

Connect the speakON cable to the [INPUT/

PARALLEL] jack correctly. When using in the

Passive mode, make sure to connect the 1+/

1– contacts of the speakON cable to the

amplifier outputs.

Sound is interrupted sud-

denly.

The speaker units are damaged.

If no sound although the connection and sig-

nal level are appropriate, there is a possibility

of malfunction of the speaker units. Contact

your Yamaha dealer.

The amplifier shuts down.

When connecting the speakers in parallel,

the total impedance of the speakers is less

than the minimum load impedance of the

amplifier.

(For example, when more than three eight-

ohm speakers are connected in parallel to

an amplifier having a minimum load imped-

ance of four ohms.)

Lower the number of speakers connected in

parallel, or use an amplifier which can drive

with the total impedance of the speakers, in

order to not be less than the minimum load

impedance of the amplifier.

The protection system of the amplifier has

been enabled because the input volume is

excessive.

Wait until the amplifier cools down. Before

using it again, lower the input volume.

No high-frequency sound.

The HF protection system has been

enabled.

Refer to the “Protection Circuit” NOTICE on

page 3.

When using in the Bi-amp mode, the signals

are sent only to the 1+/1– contacts of the

[INPUT/PARALLEL] jack.

When using in Bi-amp mode, send the correct

signals to the 1+/1– and 2+/2– contacts of the

[INPUT/PARALLEL] jack.

(1+/1–: LF, 2+/2–: HF)

Sound is distorted. Input volume is excessive.

Lower the volume of the input device so that

the limit indicator of the amplifier lights only

occasionally.

100 CZR series Owner’s Manual

Specifications

General Specifications

*1: With recommended DSP processing.

*2: Full-space (4π)

The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website

then download the manual file.

Der Inhalt dieser Bedienungsanleitung gilt für die neuesten technischen Daten zum Zeitpunkt der Veröffentlichung. Um die neueste Version der

Anleitung zu erhalten, rufen Sie die Website von Yamaha auf und laden Sie dann die Datei mit der Bedienungsanleitung herunter.

Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques connues à la date de publication du manuel. Pour obtenir la

version la plus récente du manuel, accédez au site Web de Yamaha puis téléchargez le fichier du manuel concer

né.

El contenido de este manual se aplica a las últimas especificaciones según la fecha de publicación. Para obtener el último manual, acceda al sitio

web de Yamaha y descargue el archivo del manual.

O conteúdo deste manual se aplica às especificações mais recentes a partir da data de publicação. Para obter o manual mais recente, acesse o

site da Yamaha e faça o download do arquivo do manual.

Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla data di pubblicazione. Per ottenere la versione più

recente del manuale, accedere al sito Web Yamaha e scaricare il file corrispondente.

В содержании данного руководства приведены последние на момент публикации технические характеристики. Для получения

последней версии руководства посетите веб-сайт корпорации Yamaha и загрузите файл с руководством.

CZR15 CZR12 CZR10

System Type 2-way speaker, Bass-reflex

Frequency Range

(-10 dB)

Passive 43 Hz – 20 kHz 43 Hz – 20 kHz 43 Hz – 20 kHz

Normal

34 Hz – 20 kHz 42 Hz – 20 kHz 46 Hz – 20 kHz

FOH

33 Hz – 20 kHz 38 Hz – 20 kHz 43 Hz – 20 kHz

Coverage Angle H90° × V50° Rotatable,

Constant directivity horn

H90° × V60° Rotatable,

Constant directivity horn

H90° × V60° Rotatable,

Constant directivity horn

Crossover Frequency (Passive) 2.0 kHz 2.0 kHz 2.5 kHz

Nominal Impedance Passive 8 Ω 8 Ω 8 Ω

Bi-amp LF: 8 Ω, HF: 16 Ω LF: 8 Ω, HF: 16 Ω LF: 8 Ω, HF: 16 Ω

Power Rating

(EIA 426-A)

Passive NOISE 400 W 400 W 350 W

PGM 800 W 800 W 700 W

MAX 1600 W 1600 W 1400 W

Power Rating

(LF: EIA 426-A)

(HF: AES)

Bi-amp NOISE LF: 400 W, HF: 50 W LF: 400 W, HF: 50 W LF: 350 W, HF: 50 W

PGM LF: 800 W, HF: 100 W LF: 800 W, HF: 100 W LF: 700 W, HF: 100 W

MAX LF: 1600 W, HF: 200 W LF: 1600 W, HF: 200 W LF: 1400 W, HF: 200 W

Sensitivity

(1 W, 1 m)

Passive 97 dB SPL 97 dB SPL 95 dB SPL

Bi-amp LF: 99 dB SPL,

HF: 108 dB SPL

LF: 97 dB SPL,

HF: 108 dB SPL

LF: 95 dB SPL,

HF: 108 dB SPL

Maximum SPL

(Calculated, 1 m)

Passive 129 dB SPL 129 dB SPL 127 dB SPL

Bi-amp LF: 131 dB SPL,

HF: 131 dB SPL

LF: 129 dB SPL,

HF: 131 dB SPL

LF: 127 dB SPL,

HF: 131 dB SPL

Transducer LF 15" Cone, 3" Voice coil,

Neodymium magnet

12" Cone, 3" Voice coil,

Neodymium magnet

10" Cone, 3" Voice coil,

Neodymium magnet

HF 2" Voice coil, 1" Throat compression driver, Titanium diaphragm, Neodymium magnet

Enclosure Material, Finish, Color Plywood, Durable polyurea coating, Black

Floor Monitor Angle 50° Symmetrical 50° Symmetrical 50°

Dimensions

(W × H × D, with rubber feet)

450 × 761 × 460 mm 410 × 646 × 394 mm 315 × 537 × 345 mm

Net Weight 21.3 kg 18.0 kg 14.0 kg

Handles

Aluminium die-cast, Side × 2

Aluminium die-cast,

Top × 1, Side × 1

Pole Socket Ø35 mm × 2 (0° or -7°)

Rigging Points

M10 × 12

M10 × 8

M8 × 2

Connectors speakON NL4MP × 2 (Parallel)

Optional Bracket UB-DZR15H, UB-DZR15V UB-DZR12H, UB-DZR12V UB-DZR10H, UB-DZR10V

Optional Cover SPCVR-DZR15 SPCVR-DZR12 SPCVR-DZR10

Specifications (English only)

CZR series Owner’s Manual 101

Specifications

Dimensions

41672

2xM10

460

41672

329

254

257240

2xM10

2xM8

367

240

254

329

3xM10

2xM8

450

761

367

240

254

329

3xM10

2xM8

504

50°

 CZR15

Unit: mm

2xM8

3xM10

239

277

240

327

2xM8

3xM10

646

410

239

394

277

199.5240

41557

2xM10

41557

2xM10

240

327

239

277

444

50°

 CZR12

Unit: mm

102 CZR series Owner’s Manual

Specifications

Block Diagram (CZR15, CZR12, CZR10)

233

240

166

236

2xM8

2xM10

315

537

233

166

236

240

2xM10

2xM8

392

50°

236

176

145240

451

345

2xM8

2xM10

28474

2xM8

 CZR10

Unit: mm

NL4

Passive mode (Factory setting)

NL4

1±

2±

1±

2±

1±

INPUT/

PARALLEL

NL4

Bi-amp mode (Selectable)

NL4

1±

2±

1±

2±

1±

–

LF±

HF±

INPUT/

PARALLEL

2±

–

LF±

HF±

PASSIVE

X-OVER

NETWORK

CZR series Owner’s Manual 103

Yamaha Pro Audio global website

https://www.yamaha.com/proaudio/

Yamaha Downloads

https://download.yamaha.com/

ZW46810

Manual Development Group

Published 04/2018 POEI-A0

Yamaha CZR10 Návod k obsluze

Značka: Yamaha

Modelka: CZR10

Kategorie: Audio zesilovače

Typ: Návod k obsluze

Tato příručka je také vhodná pro

CZR12
CZR15

Stáhnout PDF

zpráva

v jiných jazycích

polski: Yamaha CZR10 Instrukcja obsługi
español: Yamaha CZR10 El manual del propietario
italiano: Yamaha CZR10 Manuale del proprietario
Deutsch: Yamaha CZR10 Bedienungsanleitung
svenska: Yamaha CZR10 Bruksanvisning
português: Yamaha CZR10 Manual do proprietário
français: Yamaha CZR10 Le manuel du propriétaire
Türkçe: Yamaha CZR10 El kitabı
English: Yamaha CZR10 Owner's manual
dansk: Yamaha CZR10 Brugervejledning
русский: Yamaha CZR10 Инструкция по применению
suomi: Yamaha CZR10 Omistajan opas
Nederlands: Yamaha CZR10 de handleiding
română: Yamaha CZR10 Manualul proprietarului

Yamaha CZR10 Návod k obsluze

Tato příručka je také vhodná pro

Yamaha CZR10 Návod k obsluze

v jiných jazycích

Související papíry