Indesit IWDN 61282X9 C (CZ) Uživatelská příručka

Kategorie
Pračky
Typ
Uživatelská příručka
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 9
General safety
Disposal
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Troubleshooting, 11
Service, 12
IWDN 61282X9
Instructions for use
WASHING MACHINE
English, 1
GB
Română, 13
RO
Česky, 25
CZ
Slovensky, 37
SK
HU
Magyar, 49
2
GB
Installation
! This instruction manual should be kept in a safe
place for future reference. If the washing machi-
ne is sold, transferred or moved, make sure that
the instruction manual remains with the machine
so that the new owner is able to familiarise him-
self/herself with its operation and features.
! Read these instructions carefully: they con-
tain vital information relating to the safe instal-
lation and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its
packaging.
2. Make sure that the washing machine has
not been damaged during the transportation
process. If it has been damaged, contact the
retailer and do not proceed any further with
the installation process.
3. Remove the 4 pro-
tective screws (used
during transportation)
and the rubber wa-
sher with the cor-
responding spacer,
located on the rear
part of the appliance
(see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will
need them again if the washing machine ne-
eds to be moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing machine on a flat sturdy
floor, without resting it up against walls, furni-
ture cabinets or anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the
adjustable front feet
(see figure); the angle
of inclination, measu-
red in relation to the
worktop, must not
exceed 2°.
Levelling the machine correctly will provide
it with stability, help to avoid vibrations and
excessive noise and prevent it from shifting
while it is operating. If it is placed on carpet or
a rug, adjust the feet in such a way as to allow
a sufficient ventilation space underneath the
washing machine.
Connecting the electricity and
water supplies
Connecting the water inlet hose
1. Connect the sup-
ply pipe by screwing
it to a cold water tab
using a ¾ gas threa-
ded connection (see
figure).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is
situated on the top
right-hand side of the
rear part of the ap-
pliance (see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details
table (see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
GB
3
Technical data
Model
IWDN 61282X9
Dimensions
width 59,5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical
data plate fixed to the machine
Water connec-
tion
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per
minute
Test wash
cycles in
accordance
with directives
1061/2010 and
1015/2010
Programme 2:
Cotton standard 60°C;
Programme 3:
Cotton standard 40°C.
This appliance conforms to
the following EC Directives:
- 2004/108/CE (Electroma-
gnetic Compatibility)
- 2002/96/EC
- 2006/95/EC Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct
or a wall drain located
at a height between
65 and 100 cm from
the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct sup-
plied to the tap (see
figure). The free end
of the hose should
not be underwater.
! We advise against the use of hose exten-
sions; if it is absolutely necessary, the exten-
sion must have the same diameter as the
original hose and must not exceed 150 cm in
length.
Electrical connections
Before plugging the appliance into the electri-
city socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum
power load of the appliance as indicated in
the Technical data table (see opposite);
the power supply voltage falls within the
values indicated in the Technical data table
(see opposite);
the socket is compatible with the plug of
the washing machine. If this is not the case,
replace the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extreme-
ly dangerous to leave the appliance exposed
to rain, storms and other weather conditions.
! When the washing machine has been instal-
led, the electricity socket must be within easy
reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be repla-
ced by authorised technicians.
Warning! The company shall not be held
responsible in the event that these regulations
are not respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.
4
GB
Care and maintenance
Cutting off the water and electri-
city supplies
Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system
inside the washing machine and help to pre-
vent leaks.
Unplug the washing machine when cleaning
it and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pul-
ling it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
Always leave the porthole door ajar in order
to prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cle-
aning pump which does not require any main-
tenance. Sometimes, small items (such as
coins or buttons) may fall into the pre-chamber
which protects the pump, situated in its bot-
tom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-
chamber:
1. using a screwdri-
ver, remove the cover
panel on the lower
front part of the wa-
shing machine (see
figure);
2. unscrew the lid
by rotating it anti-
clockwise (see figu-
re): a little water may
trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto
the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If
there are any cracks, it should be replaced
immediately: during the wash cycles, water
pressure is very strong and a cracked hose
could easily split open.
! Never use second-hand hoses.
GB
5
Precautions and tips
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Chil-
dren shall not play with the appliance. Clea-
ning and user maintenance shall not be made
by children without supervision.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging
the appliance from the electricity socket. Hold the plug
and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach extreme-
ly high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any circum-
stances access the internal mechanisms in an attempt
to repair it yourself.
Always keep children well away from the appliance while
it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
Before loading laundry into the washing machine, make
sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected separately
in order to optimise the recovery and recycling of the
materials they contain and reduce the impact on human
health and the environment. The crossed out “wheeled
bin” symbol on the product reminds you of your obliga-
tion, that when you dispose of the appliance it must be
separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
ON/OFF button: switches the washing machine on and
off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
DISPLAY: used to view the duration of the various cycles
available and the remaining time of a cycle in progress;
if the DELAY TIMER option has been selected, the
countdown to the start of the selected cycle will appear.
DELAY TMER button : press to set a delayed start
time for the selected wash cycle. The delay time will be
shown on the display.
WASH CYCLE PROGRESS
indicator light
s: used to
monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened.
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Consumption in off-mode: 0,5 W
Consumption in Left-on: 0,5 W
Description of the washing
machine and starting a wash cycle
WASH CYCLE
PROGRESS
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
SPIN SPEED
knob
DISPLAY
DELAY TIMER
button
GB
7
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to indicate
which phase of the cycle is currently in progress.
Function buttons and corresponding indicator
lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will
flash and only the second function will be activated; the
indicator light corresponding to the enabled option will
remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is locked
to prevent it from being opened; make sure the indicator
light is off before opening the door (wait approximately 3
minutes). To open the door during a running wash cycle,
press the START/PAUSE button; the door may be opened
once the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. Switch the washing machine on by pressing the ON/OFF button. All indicator lights will switch on for a few seconds, then
they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed
manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the indicator light will switch on. The door can be opened once the DOOR LOCK indi-
cator light turns off. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely. Switch
the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
8
GB
Wash cycles
Table of wash cycles
Outwear (wash cycle 9): is studied for washing water-repellent fabrics and winter jackets (e.g. Gore-Tex, polyester, nylon); for
best results, use a liquid detergent and dosage suitable for a half-load; pre-treat necks, cuffs and stains if necessary; do not
use softeners or detergents containing softeners. Stuffed duvets cannot be washed with this programme.
Sport Intensive (wash cycle 12) is for washing heavily soiled sports clothing fabrics (tracksuits, shorts, etc.); for best re-
sults, we recommend not exceeding the maximum load indicated in the “Table of wash cycles”.
Sport Light (wash cycle 13) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best results, we
recommend not exceeding the maximum load indicated in the “Table of wash cycles”. We recommend using a liquid deter-
gent and dosage suitable for a half-load.
Special Shoes (wash cycle 14) is for washing sports shoes; for best results, do not wash more than 2 pairs simultaneously.
The 20° wash cycles (20° Zone) offer effective washing performance at low temperatures, reducing electricity usage and
expenditure while benefitting the environment.The 20° wash cycles meet all requirements:
Cotton Standard 20° (programme 6) ideal for heavily soiled cotton loads. The effective performance levels achieved at
cold temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at
varying speed, with repeated and frequent peaks.
Mix Light (programme 7) ideal for mixed loads (cotton and synthetics) with a normal soil level. The effective performance
levels achieved at cold temperatures are guaranteed by a mechanical action which operates at varying speed, across set
average intervals.
20’ Refresh (programme 8) ideal for refreshing and washing lightly soiled garments in a few minutes. It lasts just 20 minutes
and therefore saves both time and energy. It can be used to wash different types of fabrics together (except for wool and
silk), with a maximum load of 1.5 kg.
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 2 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 3 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments
which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.
3) Long wash cycle for synthetics: set wash cycle 4; with a temperature of 40°C.
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
Wash cycles
Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load (kg)
Residual
dampness
%
Energy
consum-
ption kWh
Total water lt
Cycle
duration
Wash
Fabric
softener
Daily
1
White Cotton: extremely soiled whites. 90° 1200
6 53 2,10 70 125’
2
Cotton Standard 60° (1): heavily soiled whites and resistant colours. 60° 1200
6 53 0,87 51 150’
3
Cotton Standard 40° (2): lightly soiled whites and delicate colours. 40° 1200
6 53 1,09 92 145’
4
Synthetics: heavily soiled resistant colours. 50° 800
3,5 - - - 110’
4
Synthetics (3): lightly soiled resistant colours. 40° 800
3,5 44 0,57 46 100’
5
Mix Colored: lightly soiled whites and delicate colours. 40° 1200
6 53 0,60 50 85’
20° Zone
6
Cotton Standard 20°: lightly soiled whites and delicate colours.
20°
1200
6 - - - 170’
7 Mix Light
20° 800
6 - - - 120’
8 20’ Refresh
20° 800
1,5 - - - 20’
Special
9 Outwear
30° 400
-
2 - - - 60’
10
Wool: for wool, cashmere, etc.
40° 800
1,5 - - - 70’
11 Jeans
40° 800
3,5 - - - 75’
Sport
12 Sport Intensive
30° 600
3 - - - 85’
13 Sport Light
30° 600
3 - - - 60’
14 Special Shoes
30° 600
Max. 2
pairs
- - - 60’
Partial wash cycles
Rinse - 1200 -
6 - - - 36’
Spin + Drain - 1200 - - 6 - - - 16’
GB
9
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash .
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 1200 rpm
Synthetics 800 rpm
Wool 800 rpm
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the
selected wash cycle.
Delay timer
To set a delayed start for the selected programme, press the corresponding button repeatedly until the required delay period
has been reached. When this option is enabled, the symbol lights up on the display. To remove the delayed start option
press the button until the text “OFF” appears on the display.
! This option is enabled with all programmes.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly soiled
cotton and synthetic fabrics (refer to the
“Table of wash cycles”
). “ ” enables you to wash in less time thereby saving
water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
! This function may not be used in conjunction with wash cycles 1, 6, 7, 8, 9, 10, 11, 12, 13, 14, , .
The function saves energy by not heating the water used to wash your laundry - an advantage both to the
environment and to your energy bill. Instead, intensified wash action and water optimisation ensure great wash results in the
same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid detergent.
! This function may not be used in conjunction with wash cycles 6, 7, 8, 10, 12, 13, 14, , .
Personalisation
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessa-
rily result in a more efficient wash, and may in fact cause
build up on the inside of your appliance and contribute to
environmental pollution.
! Do not use hand washing detergents because these
create too much foam.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
Open the detergent di-
spenser drawer and pour
in the detergent or washing
additive, as follows.
compartment 1: Do not pour detergent into this
compartment.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
• Empty all garment pockets and check the buttons.
Do not exceed the values listed in the “Table of wash
cycles”, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Wool: all wool garments can be washed using programme
10, even those carrying the “hand-wash only” label.
For best results, use special detergents and do not exceed
1,5 kg of laundry.
Jeans: Turn garments inside-out before washing and use
a liquid detergent. Use programme 11.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
1
2
3
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (“H2O” will flash on
the display).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
Thefunction indicator lights and
thestart/pauseindicator light flash,
while one of thephase in progress
indicator lights and the door locked
indicator light will remain lit in a fixed
manner.
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see “Personalisation”).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from the floor
(see “Installation”).
The free end of the hose is under water (see “Installation”).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the drain
phase to be started manually.
The drain hose is bent (see “Installation”).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see “Installation”).
The washing machine is not level (see “Installation”).
The washing machine is trapped between cabinets and walls (see “Installation”).
The water inlet hose is not screwed on properly (see “Installation”).
The detergent dispenser drawer is blocked (for cleaning instructions, see “Care
and maintenance”).
The drain hose is not fixed properly (see “Installation”).
Switch off the machine and unplug it, wait for approximately 1 minute and then
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text
“for washing machines” or “hand and machine wash”, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see “Troubleshooting”);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
13
RO
Română
Sumar
Instalare, 14-15
Despachetare şi punere la nivel
Racorduri hidraulice şi electrice
Primul ciclu de spălare
Date tehnice
Întreţinere şi curăţare, 16
Întreruperea alimentării cu apă şi curent electric
Curăţarea maşinii de spălat
Curăţarea compartimentului pentru detergent
Îngrijirea uşii şi a tamburului
Curăţarea pompei
Controlarea furtunului de alimentare cu apă
Precauţii şi sfaturi, 17
Norme de protecţie şi siguranţă generale
Aruncarea reziduurilor
Descrierea maşinii de spălat şi activarea unui
program, 18-19
Panoul de control
Indicatoare luminoase
Activarea unui program
Programe, 20
Tabel de programe
Personalizare, 21
Reglarea temperaturii
Reglarea centrifugării
Funcţii
Detergenţi şi rufe albe, 22
Compartimentul pentru detergenţi
Pregătirea rufelor
Articole delicate
Sistemul de echilibrare a încărcăturii
Anomalii şi remedii, 23
Asistenţă, 24
RO
IWDN 61282X9
Instrucţiuni de folosire
MAŞINĂ DE SPĂLAT RUFE
14
RO
Instalare
! Este important să păstraţi acest manual
pentru a-l putea consulta în orice moment.
În caz de vânzare, de cesiune sau de schim-
bare a locuinţei, acesta trebuie să rămână
împreună cu maşina de spălat pentru a infor-
ma noul proprietar cu privire la funcţionare şi
la respectivele avertismente.
! Citiţi cu atenţie instrucţiunile: veţi găsi
informaţii importante cu privire la instalare, la
folosire şi la siguranţă.
Despachetare şi punere la nivel
Despachetare
1. Scoaterea din ambalaj a maşinii de spălat.
2. Controlaţi ca maşina de spălat să nu  fost
deteriorată în timpul transportului. Dacă este
deteriorată nu o conectaţi şi luaţi legătura cu
vânzătorul.
3. Scoateţi cele 4
şuruburi de protecţie
pentru transport şi
cauciucul cu respec-
tivul distanţier, situate
în partea posterioară
(a se vedea gura).
4. Închideţi oriciile cu dopurile din plastic
aate în dotare.
5. Păstraţi toate piesele: pentru cazul în care
maşina de spălat va trebui e transportată,
piesele vor trebui montante din nou.
! Ambalajele nu sunt jucării pentru copii!
Punere la nivel
1. Instalaţi maşina de spălat pe o suprafaţă
plană şi rigidă, fără a o sprijini de ziduri,
mobilă sau altceva.
2. Dacă podeaua
nu este perfect
orizontală, compensi
neregularităţile
deşurubând
sau înşurubând
picioruşele anterioare
(a se vedea gura);
unghiul de înclinare,
măsurat pe planul de
lucru, nu trebuie să depăşească 2°.
O nivelare precisă conferă stabilitate maşinii
şi evită vibraţii, zgomote şi deplasări pe
timpul funcţionării. În cazul mochetelor sau
a unui covor, reglaţi picioruşele astfel încât
să menţineţi sub maşina de spălat un spaţiu
sucient pentru ventilare.
Racorduri hidraulice şi electrice
Racordarea furtunului de alimentare cu
apă
1. Conectaţi tu-
bul de alimentare,
înşurubându-l la un
robinet de apă rece
cu gura letată de
3/4 gaz (a se vedea
gura).
Înainte de conectare,
lăsaţi apa să curgă
până când nu a devi-
ne limpede.
2. Conectaţi tubul
de alimentare la
maşina de spălat,
înşurubându-l la sur-
sa de apă respectivă,
amplasată în partea
posterioară, sus în
dreapta (a se vedea
gura).
3. Fiţi atenţi ca furtunul să nu e nici pliat nici
îndoit.
! Presiunea apei de la robinet trebuie să e
cuprinsă în valorile din tabelul Date tehnice
(a se vedea pagina alăturată).
! Dacă lungimea furtunului de alimentare nu
este sucientă, adresaţi-vă unui magazin
specializat sau unui instalator autorizat.
! Nu folosiţi niciodată tuburi folosite deja.
! Utilizaţi tuburile furnizate împreună cu
maşina.
15
RO
Date tehnice
Model IWDN 61282X9
Dimensiuni
lãrgime 59,5 cm
înãlþime 85 cm
profunzime 53,5 cm
Capacitate de la 1 la 6 kg
Legãturi
electrice
Vezi placuta cu caracteri-
sticile tehnice, aplicata pe
masina.
Legãturi
hidrice
presiune maximã
1 MPa (10 bari)
presiune minimã
0,05 MPa (0,5 bari)
capacitatea cuvei 52 litri
Viteza de
centrifugare
pânã la 1200 de rotaþii pe
minut
Programe
de control
conform
directivelor
1061/2010
şi
1015/2010
Programul 2: program
standard la 60°C pentru
rufe din bumbac.
Programul 3: program
standard la 40°C pentru
rufe din bumbac.
Acest aparat este con-
form cu urmãtoarele
Directive Comunitare:
- 2004/108/CE (Compatibi-
litate Electromagneti)
- 2006/95/CE (Tensiuni
Joase)
-2002/96/CE
Zgomot
(dB(A)
re 1 pW
Spãlare: 54
Centrifugare: 80
65 - 100 cm
Conectarea furtunului de golire
Conectaţi furtunul de
golire - fără a-l îndoi
- la canalizare sau
la racordul de golire
prevăzut pe perete,
la o înălţime de 65 -
100 cm de sol;
Sprijiniţi-l de margi-
nea căzii sau chiu-
vetei şi racordaţi
şina de ghidare din
dotare la robinet (a
se vedea gura).
Capătul liber al fur-
tunului de golire nu
trebuie să rămână
cufundat în apă.
! Nu se recomandă folosirea furtunurilor pre-
lungitoare; dacă este indispensabil, acestea
trebuie să aibă acelaşi diametru ca şi furtunul
original şi nu trebuie să depăşească 150 cm
lungime.
Racordarea electrică
Înainte de a introduce stecherul în priză,
asiguraţi-vă ca:
priza să e cu împământare şi conform
prevederilor legale;
priza să poată suporta sarcina maximă de
putere a maşinii, indicată în tabelul Date
Tehnice (a se vedea alături);
tensiunea de alimentare să e cuprinsă în
valorile indicate în tabelul Date Tehnice (a
se vedea alături);
priza să e compatibilă cu stecherul maşinii
de spălat. În caz contrar înlocuiţi stecherul.
! Maşina de spălat nu trebuie instalată
afară, nici chiar în cazul în care spaţiul este
adăpostit, deoarece este foarte periculoasă
expunerea maşinii la ploi şi furtuni.
! După instalarea maşinii de spălat, priza de
curent trebuie să e uşor accesibilă.
! Nu folosiţi prelungitoare şi prize multiple.
! Cablul nu trebuie să e îndoit sau comprimat.
! Cablul de alimentare trebuie să e înlocuit
doar de tehnicieni autorizaţi ai centrului de
service ce apare scris pe certicatul de ga-
rantie emis de producator.
Atenţie! Producătorul îşi declină orice re-
sponsabilitate în cazul în care aceste norme
nu se respectă.
Primul ciclu de spălare
După instalare, înainte de folosire, efectuaţi
un ciclu de spălare cu detergent şi fără rufe,
selectând programul 2.
16
RO
Întreruperea alimentării cu apă şi
curent electric
Închideţi robinetul de apă după ecare
spălare. Se limitează astfel uzura instalaţiei
hidraulice a maşinii de spălat şi se elimină
pericolul scurgerilor.
Scoateţi stecherul din priza de curent atun-
ci când curăţaţi maşina de spălat şi când se
efectuează lucrări de întreţinere.
Curăţarea maşinii de spălat
Partea externă şi părţile din cauciuc pot 
curăţate cu o lavetă înmuiată în apă călduţă
şi săpun. Nu folosiţi solvenţi sau substanţe
abrazive.
Curăţarea compartimentului pentru
detergent
Trageti afara compa-
timentul ridicându-l
si tragându-l spre
exterior (a se vedea
gura).
Spălaţi-l sub un jet de
apă; această operaţie
trebuie efectuată cât
mai des posibil.
Îngrijirea uşii şi a tamburului
Lăsaţi mereu uşa întredeschisă pentru a
evita formarea de mirosuri neplăcute.
Curăţarea pompei
Maşina de spălat este dotată cu o pompă
de autocurăţare care nu are nevoie de
întreţinere. Se poate întâmpla însă ca unele
obiecte mici (monede, nasturi) să cadă în
anticamera care protejează pompa, situată în
partea inferioară a acesteia.
! Vericaţi ca ciclul de spălare să e încheiat
şi scoateţi stecherul din priză.
Pentru a avea acces la anticameră:
1. scoateţi panoul de
acoperire din partea
din faţă a maşinii
de spălat folosind o
şurubelniţă
(a se vedea gura);
2. deşurubaţi capa-
cul rotindu-l în sens
invers acelor de ce-
asornic (a se vedea
gura). Este normal
să iasă puţină apă;
3. curăţaţi cu grijă interiorul;
4. înşurubaţi la loc capacul;
5. montaţi din nou panoul vericând, înainte
de a-l împinge spre maşină, de a  introdus
cârligele în oriciile respective.
Controlarea furtunului de alimentare cu
apă
Controlaţi tubul de alimentare cel puţin o
dată pe an. Dacă prezintă crăpături sau suri
trebuie înlocuit: pe parcursul spălărilor, pre-
siunea puternică ar putea provoca crăpături
neaşteptate.
! Nu folosiţi niciodată tuburi folosite deja.
Întreţinere şi curăţare
17
RO
Pentru informaţii suplimentare cu privire la scoaterea din uz
a electrocasnicelor, deţinătorii acestora pot apela la centrele
de colectare a deşeurilor sau la vânzătorii de la care au
achiziţionat produsele respective.
Atenţionãri în conformitate cu legislaţia în vigoare
• Conform prevederilor legislaţiei privind gestiona-
rea deşeurilor, este interzisã eliminarea deşeurilor de
echipamente electrice şi electronice (DEEE) alãturi de
deşeurile municipale nesortate. Ele trebuie predate la
punctele municipale de colectare, societãţile autorizate
de colectare/reciclare sau distribuitori (în cazul în care se
achiziţioneazã echipamente noi de acelaşi tip).
Autoritãţile locale trebuie sã asigure spaţiile nece-
sare pentru colectarea selectivã a deşeurilor precum
şi funcţionalitatea acestora. Contactaţi societatea de
salubrizare sau compartimentul specializat din cadrul
primãriei pentru informaţii detaliate.
• Deşeurile de echipamente electrice şi electronice pot 
predate şi distribuitorilor, la achiziţionarea de echipamen-
te noi de acelaşi tip (schimb 1 la 1).
• Predarea, de cãtre utilizatori, a deşeurilor de echipa-
mente electrice şi electronice, la punctele de colectare
municipale, societãţile autorizate de colectare/recicla-
re sau distribuitori (în cazul în care se achiziţioneazã
echipamente noi de acelaşi tip) faciliteazã refolosirea,
reciclarea sau alte forme de valoricare a acestora.
• Deşeurile de echipamente electrice şi electronice pot
conţine substanţe periculoase care pot avea un impact
negativ asupra mediului şi sãnãtãţii umane în cazul în
care DEEE nu sunt colectate selectiv şi gestionate con-
form prevederilor legale.
• Simbolul alãturat (o pubela cu roţi, barata cu
douã linii în forma de X), aplicat pe un echipament
electric sau electronic, semnicã faptul cã acesta
face obiectul unei colectãri separate şi nu poate 
eliminat împreunã cu deşeurile municipale nesortate.
Precauţii şi sfaturi
! Maşina de spălat a fost proiectaşi construită conform
normelor internaţionale de protecţie. Aceste avertiri sunt fur-
nizate din motive de siguranţă şi trebuie e citite cu atenţie.
Norme de protecţie şi siguranţă generale
• Acest aparat a fost conceput exclusiv pentru utilizarea
în locuinţe unifamiliale.
Aparat aparat poate  folosit de copii în-
cepând cu vârsta de 8 ani şi de persoane
cu capacităţi zice, senzoriale sau menta-
le reduse sau cu experienţă şi cunoştinţe
insuciente dacă sunt supravegheate sau
dacă au primit o pregătire adecvată pri-
vind folosirea aparatului în mod sigur şi
înţelegând pericolele respective. Copiii nu
trebuie să se joace cu aparatul. Întreţinerea
şi curăţarea nu trebuie să e efectuate de
copii fără supraveghere.
• Nu atingeţi maşina când sunteţi desculţi sau cu mâinile
sau picioarele ude sau umede.
• Nu scoateţi stecherul din priză trăgând de cablu.
• Nu deschideţi compartimentul pentru detergent în timp
ce maşina se aă în funcţiune.
• Nu atingeţi apa golită din maşină: poate avea o
temperatură ridicată.
• Nu forţaţi în nici un caz uşa: s-ar putea deteriora
mecanismul de siguranţă care evită deschiderea
accidentală.
• În caz de defecţiune, nu umblaţi în nici un caz la meca-
nismele din interior şi nu încercaţi să o reparaţi singuri.
• Controlaţi mereu ca în apropierea maşinii aate în
funcţiune, să nu se ae copii.
• Pe durata spălării uşa se poate încălzi.
• Dacă trebuie să deplasaţi maşina, cereţi ajutor unei alte
(sau 2) persoane şi ţi foarte atenţi. Niciodată nu deplasaţi
maşina singuri deoarece aceasta este foarte grea.
• Înainte de a introduce rufele, controlaţi cuva să e
goală.
Aruncarea reziduurilor
• Eliminarea ambalajelor: respectaţi normele locale, în
acest fel ambalajele vor putea  utilizate din nou.
• Directiva Europeană 2002/96/CE cu privire la deşeurile care
provin de la aparatura electrică sau electroni prevede ca
aparatele electrocasnice să nu e colectate împreună cu
deşeurile urbane solide, obişnuite. Aparatele scoase din uz
trebuie să e colectate separat atât pentru a optimiza rata de
recuperare şi de reciclare a materialelor componente cât şi
pentru a evita pericolele care pot duce la dăunarea săţii
omului sau poluarea mediului înconjurător. Simbolul tom-
beronului tăiat care apare pe toate produsele amintte
tocmai obligia de a le colecta separat.
18
RO
Sertarul detergenţilor: pentru a introduce detergenţi
sau aditivi (a se vedea “Detergenţi şi rufe albe”).
Tasta ON/OFF: pentru a porni şi opri maşina.
Selector PROGRAME: pentru a selecta programele.
Pe durata desfăşurării programului selectorul rămâne în
aceeaşi poziţie.
Taste cu led FUNCŢII: pentru a selecta funcţiile disponi-
bile. Indicatorul corespunzător funcţiei alese va rămâne
aprins.
Selector CENTRIFUGARE: pentru a activa / anula centri-
fugarea (a se vedea “Personalizare”).
Selector TEMPERATURĂ: pentru a selecta temperatura
sau spălarea la rece (a se vedea “Personalizare”).
DISPLAY: pentru a aşa durata diferitelor programe la
dispoziţie şi a celui restant, în cazul unui ciclu de spălare
deja în desfăşurare; dacă a fost programat un interval
de PORNIRE ÎNTÂRZIATĂ, este aşat intervalul restant
până la pornirea programului selectat.
Tastă PORNIRE ÎNTÂRZIA : apăsaţi pentru a pro-
grama pornirea maşinii la o anumită oră. Întârzierea va 
indicată pe display.
Indicatoare DESFĂŞURARE CICLU: pentru a putea
urmări avansarea programului de spălare.
Indicatorul aprins arată faza în curs de desfăşurare.
Indicator UŞĂ BLOCATĂ: pentru a înţelege dacă uşa se
poate deschide sau nu (a se vedea pag. alăturată).
Tastă cu led START/PAUSE: pentru a activa / opri mo-
mentan programele.
N.B.: pentru a întrerupe momentan un ciclu apăsaţi
această tastă; ledul se va aprinde intermitent (culoare
portocalie) în timp ce ledul corespunzător fazei în curs
de desfăşurare va rămâne aprins. Dacă indicatorul UŞĂ
BLOCA este stins, atunci uşa se poate deschide.
Pentru a continua spălarea, de unde a fost întreruptă,
apăsaţi din nou tasta.
Modalitatea de stand by
Această maşină de spălat rufe, conform noilor norme
legate de economia de curent electric, este dotată cu
un sistem de oprire automat (stand-by) care intră în
funcţiune după 30 minute de neutilizare. Apăsaţi scurt ta-
sta ON/OFF şi aşteptaţi repunerea în funcţiune a maşinii.
Consum în off-mode: 0,5 W
Consum în Left-on: 0,5 W
Descrierea maşinii de spălat şi
activarea unui program
Indicator
UŞĂ BLOCA
Tastă cu led
START/
PAUSE
Panoul de control
Sertarul detergenţilor
Tasta
ON/OFF
Selector
PROGRAME
Selector
TEMPERATURĂ
Selector
CENTRIFUGARE
Taste cu led
FUNCŢII
Indicatoare
DESFĂŞURARE CICLU
DISPLAY
Tastă
PORNIRE
ÎNTÂRZIA
19
RO
Indicatoare luminoase
Ledurile furnizează informaţii importante.
Iată ce indică:
Indicatoare de fază
După alegerea şi activarea ciclului dorit, indicatoarele
luminoase se vor aprinde unul după altul, ceea ce vă
indică starea de avansare a programului:
Tastele de funcţii şi ledurile corespunzătoare
Alegerea unei funcţii implică aprinderea ledului
corespunzător.
Dacă funcţia selectată nu este compatibilă cu programul
ales, ledul corespunzător se va aprinde intermitent iar
funcţia nu se va activa.
Dacă funcţia aleasă nu este compatibilă cu o funcţie
selectată anterior, indicatorul care corespunde primei
funcţii va emite un semnal intermitent iar indicatorul celei
de a doua se va aprinde: acest lucru înseamnă că se va
activa numai a doua funcţie (ultima aleasă).
Indicator uşă blocată:
Aprinderea ledului indică faptul că hubloul s-a blocat,
pentru a împiedica deschiderea sa; pentru a putea
deschide hubloul, aşteptaţi aproximativ 3 minute, până
la stingerea ledului. Pentru a deschide hubloul în timpul
executării unui ciclu, apăsaţi tasta PORNIRE/PAUZĂ;
dacă ledul UŞĂ BLOCATĂ este stins, atunci puteţi de-
schide hubloul.
Activarea unui program
1. Porniţi maşina de spălat apăsând pe tasta ON/OFF. Toate indicatoarele se aprind câteva secunde, apoi se sting; indi-
catorul START/PAUSE se va aprinde intermitent.
2. Introduceţi rufele şi închideţi uşa.
3. Selectaţi programul dorit cu ajutorul selectorului de PROGRAME.
4. Reglaţi temperatura de spălare (a se vedea “Personalizare”).
5. Reglaţi viteza de centrifugare (a se vedea “Personalizare”).
6. Adăugaţi detergentul şi aditivii (a se vedea “Detergenţi şi rufe”).
7. Alegeţi funcţiile dorite.
8. Activaţi programul apăsând tasta START/PAUSE; indicatorul luminos se va aprinde (culoare verde).
Pentru a anula un ciclu selectat, apăsaţi tasta START/PAUSE pentru a întrerupe momentan ciclul şi alegeţi un nou pro-
gram.
9. La încheierea programului, indicatorul luminos se va aprinde. După stingerea ledului corespunzător avertizării de
UŞĂ BLOCATA , este posibilă deschiderea hubloului. Scoateţi rufele şi lăsaţi uşa întredeschisă pentru a se putea usca
cuva si tamburul. Opriti maşina de spălat apăsând pe tasta ON/OFF.
Spălare
Clătire
Centrifugă
Golire
Sfârşit Spălare
20
RO
Outwear (programul 9) a fost studiat pentru spălarea ţesăturilor hidrofobe şi a gecilor rezistente la vânt (ex. goretex, poliester, nailon);
pentru a obţine cele mai bune rezultate, utilizaţi detergent lichid într-o cantitate adecvată unei încărcări pe jumătate a maşinii; desfaceţi
manşetele, gulerele şi scoateţi petele; nu utilizaţi balsam de rufe sau detergent cu balsam. Acest program nu poate utilizat pentru
spălarea pufoaicelor căptuşite.
Sport Intensive (programul 12) a fost studiat pentru spălarea ţesăturilor utilizate la confecţionarea hainelor sportive (echipamente,
pantaloni scurţi etc.) foarte murdare; pentru cele mai bune rezultate, se recomandă să nu depăşiţi cantitatea maximă admisă indicată în
„Tabel de programe”.
Sport Light (programul 13) a fost studiat pentru spălarea ţesăturilor utilizate la confecţionarea hainelor sportive (echipamente, pantaloni
scurţi etc.) puţin murdare; pentru cele mai bune rezultate, se recomandă să nu depăşiţi cantitatea maximă admisă indicată în „Tabel de
programe”. Se recomandă utilizarea detergentului lichid într-o cantitate adecvată unei încărcări pe jumătate a maşinii.
Sport Shoes (programul 14) a fost studiat pentru spălarea pantolor de sport; pentru cele mai bune rezultate, nu spălaţi mai mult de 2
perechi deodată.
Programele 20° (20° Zone) oferă performanţe bune de spălare la temperaturi scăzute, permiţând o folosire redusă a energiei electrice,
ceea ce înseamnă un beneciu pentru mediul înconjurător şi o economie de bani.
Programele 20° corespund tuturor exigenţelor:
Program standard la 20 °C pentru rufe din bumbac
(programul 6) ideal pentru rufe de bumbac murdare. Performanţele bune şi la rece, com-
parabile cu o slare la 40°, sunt garantate de o acţiune mecani care lucrea prin varierea vitezei la intervale repetate şi apropiate.
Mix Light (programul 7) ideal pentru rufe mixte (bumbac şi sintetice) cu grad normal de murdărie. Performanţele bune de spălare şi la
rece sunt garantate de o acţiune mecanică care lucrează prin varierea vitezei la intervale medii şi determinate.
20 Refresh (programul 8) ciclul ideal pentru a împrospăta şi spăla rufe uşor murdare în câteva minute. Durea doar 20 de minute ceea ce
economiseşte energie şi timp. Este posibil slaţi împreună ţesuturi diferite (în afară de nă şi tase); greutatea maximă admieste de 1,5 kg.
Programe
Tabel de programe
Durata ciclului indicată pe display sau în carte este calculată în baza unor condiţii standard. Timpul efectiv poate varia în baza a numeroşi factori, precum temperatura şi presiunea apei la
intrare, temperatura mediului, cantitatea de detergent, cantitatea şi tipul încărcăturii, echilibrarea încărcăturii, opţiunile suplimentare selectate.
1) Programul de control conform normei 1061/2010: selectaţi programul 2 şi temperatura de 60°C.
Acest ciclu este potrivit pentru curăţarea unei încărcături de bumbac cu grad de murdărie normal şi este cel mai ecient din punct de vedere al consumului combinat
de energie şi apă; se foloseşte pentru articole de îmbrăcăminte care pot  spălate la 60°C. Temperatura efectivă de spălare poate diferi de cea indicată.
2) Programul de control conform normei 1061/2010: selectaţi programul 3 şi temperatura de 40°C.
Acest ciclu este potrivit pentru curăţarea unei încărcături de bumbac cu grad de murdărie normal şi este cel mai ecient din punct de vedere al consumului combinat
de energie şi apă; se foloseşte pentru articole de îmbrăcăminte care pot  spălate la 40°C. Temperatura efectivă de spălare poate diferi de cea indicată.
Pentru toate Instituţiile de Testare:
2) Program pentru bumbac, prelungit: selectaţi programul 3 şi temperatura de 40°C.
3) Program sintetic de-a lungul: selectaţi programul 4 şi temperatura de 40°C.
Programe
Descrierea Programului
Temp.
max.
(°C)
Viteza
max.
(rotaþii
pe mi-
nut)
Detergenþi
Sarcina Max.
(Kg)
Umiditate
rezidualã %
Consum ener-
gie kWh
Apã totalã lt
Durata ciclului
de slare
Spã-
lare
Balsam
rufe
Programe zilnice (Daily)
1
RUFE ALBE BUMBAC: Rufe albe foarte murdare.
90° 1200
6 53 2,10 70 125
2
Program standard la 60°C pentru rufe din bumbac (1): Albe ºi colo-
rate rezistente foarte murdare.
60° 1200
6 53 0,87 51 150
3
Program standard la 40°C pentru rufe din bumbac (2): Albe ºi colo-
rate delicate puþin murdare.
40° 1200
6 53 1,09 92 145
4
SINTETICE: Colorate rezistente foarte murdare.
50° 800
3,5 - - - 110
4
SINTETICE (3): Colorate delicate putin murdare.
40° 800
3,5 44 0,57 46 100
5
COLORATE BUMBAC: Albe puþin murdare ºi colorate delicate.
40° 1200
6 53 0,60 50 85’
20° Zone
6
Program standard la 20°C pentru rufe din bumbac: Albe ºi colorate
delicate puþin murdare.
20° 1200
6 - - - 170’
7
Mix Light
20° 800
6 - - - 120’
8
20’ Refresh
20° 800
1,5 - - - 20’
Programe Speciale (Special)
9
Outwear
30° 400
-
2 - - - 60’
10
LÂNÃ: Pentru articole din lânã, caºmir.
40° 800
1,5 - - - 70’
11
JEANS
40° 800
3,5 - - - 75’
Sport
12
Sport Intensive
30° 600
3 - - - 85’
13
Sport Light
30° 600
3 - - - 60’
14
Sport Shoes
30° 600
(Max 2
perechi.)
- - - 60’
Programe parþiale
CLÃTIRE
- 1200 -
6 - - - 36’
CENTRIFUGARE + EVACUARE
- 1200 - -
6 - - - 16’
1 / 1

Indesit IWDN 61282X9 C (CZ) Uživatelská příručka

Kategorie
Pračky
Typ
Uživatelská příručka