Haier HRFZ-250D Uživatelský manuál

HRFZ-250D AA

FRIDGE FREEZER

USER'S INSTRUCTIONS

N

a

m

e

o

f

p

a

r

t

s

○

11

Freezer Door

○

1

Top Cover

○

2

Wire Shelf

○

3

Thermostat and Lamp assembly

○

4

Door Switch

○

5

Glass Shelves

○

6

Crisper Cover

○

7

Crisper

○

8

Adjustable Front Feet

○

9

Door Balconies

○

10

Fridge Door Gasket

1

8

9

10

11

Thank you for buying this Haier fridge-freezer. To ensure that you get the best results from

your new fridge, please take time to read through these simple instructions in this booklet.

Please ensure that the packaging material is disposal of in accordance with the current

environmental requirements.

If the appliance is visibly damaged, do not connect it to the power supply, contact the store from

where you purchased the appliance.

ELECTRICAL CONNECTION UK ONLY

For your safety please read the following information

Warning This appliance must be earthed.

This appliance operates from 220-240 volts and should be protected by a 13 amp fuse in the plug.

The appliance is supplied with a standard 13 amp 3 pin plug fitted with a 13 amp fuse.

Should the fuse require replacement, it must be replaced with a fuse rated at 13 amp and

approved to BS1362.

If the mains plug which is fitted is unsuitable for the socket outlet in your home or is removed

for any other reason, please follow the instructions below on how to wire a 13 amp 3 pin plug.

How to wire a 13 amp plug.

Important. The wires in the mains lead on this appliance are coloured in accordance with the

following code:

Green and Yellow – Earth

Blue – Neutral

Brown – Live

As the colours may not correspond with the markings

identifying the terminals in your plug proceed as follows:

the Green and Yellow wire must be connected to the

the terminal in the plug which is marked with the letter E or

with the earth symbol or coloured green and yellow.

he Brown wire must be connected to the terminal marked L or

The Blue wire must be connected to the terminal marked

N or coloured black.

T

Coloured red.

Make sure the mains cord is held securely under the cord clamp.

2

Warnings:

Keep ventilation openings, in the appliance enclosure or in the built in structure,

clear of obstructions.

Do not use mechanical devices or other means to accelerate the defrost process,

other than those recommended by the manufacturer.

Do not damage the refrigerant circuit.

Do not use electrical devices inside the food storage compartments of the appliance,

unless they are of the type recommended by the manufacturer.

THANK YOU FOR PURCHASING THIS HAIER PRODUCT

This booklet contains the information you will require to install and operate your new

appliance.

It is important and worthwhile spending time to fully read this booklet so you will

understand how to operate the appliance safely and efficiently.

Please keep this booklet in a safe place so that you can refer to it when required.

Safety information

This information is provided in the interest of your safety. Please read the following

carefully before carrying out the installation or use of the appliance.

If you are discarding an old freezer or refrigerator with a lock / catch fitted to the

door, ensure that it is left in a disabled condition to prevent the entrapment of young

children when playing.

As old refrigeration equipment may contain CFC’s which will damage the ozone

layer, when disposing of any refrigeration equipment please contact your local waste

disposal department for advice on the correct method of disposal

This appliance must only be used for its intended purpose i.e. the storage of domestic

edible foodstuffs and should not be used for any other purpose

If the mains cable becomes damaged, it must be replaced by the manufacturer, its

service agent or a similarly qualified person to avoid a hazard.

Installation

Position the appliance and allow to stand for two to three hours before it is turned on

for the first time to allow the system to settle. Do not position next to any heat source

e.g. cooker, boiler or in direct sunlight etc.

A clearance of 10 cm must be left between the sides of the appliance and any adjacent

cabinets or walls to allow for adequate air circulation. The appliance is not designed

for recessed installation (“building in”).

Install on a good firm level surface, and any unevenness of the floor should be

corrected prior to installation, slight unevenness can be overcome by adjusting the

front feet.

NOTE: If the appliance is positioned on a carpet, soft floor covering you should re-

adjust the front feet once the appliance has had time to settle.

3

IMPORTANT SAFETY INFORMATION

This appliance must be used on the electric voltage shown on the rating plate

on the base of this appliance, failu

re to use the correct voltage will render the

guarantee VOID and may cause damage to the product.

This appliance is intended for domestic use only, any other use may invalidate

the warranty and might be dangerous.

This appliance is intended for indoor use only, do not use outdoors.

Accessible surfaces may get hot during operation, use handles and knobs at all

times.

To protect against electric shock do not immerse cord, plugs, or appliance in

water or other liquid.

Do not attempt to dislodge food when product is in operation.

Unplug from outlet when not in use and before cleaning. Remove food before

cleaning the appliance.

If the mains lead becomes damaged, it must be replaced by the manufacturer,

its service agent or similarly qualified

person with a lead of the same type and

rating to avoid a hazard.

Do not operate the appliance with a damaged cord or plug or after the

appliance malfunctions or

has been damaged in any way. Consult the retail

store where you bought the appliance for advice.

The cooling circuit must not be damaged in any way.

Do not insert over sized food as this could cause a hazard.

Do not let cord hang over edge of the surface, or touch hot surfaces.

Do not place appliance on or near hot surfaces, or in direct sunlight.

Extreme caution must be used when moving an appliance.

Always attach a plug to appliance, then plug cord in the wall outlet. To

disconnect, turn the switch OFF, then remove the plug from wall outlet.

A short power-supply cord is provided to reduce the risk of a tripping

hazard.

4

5

Temperature Control

The refrigerator is designed to maintain an internal storage temperature in the

refrigerator compartment between to + .

Instructions for use

Remove all packing materials and wash the interior of the appliance using lukewarm

water containing a little bicarbonate of soda in the proportion of 1 teaspoon to 1.2 liters

(2 pints) of water. Do not use detergents or soaps as they may taint the food. After

cleaning, dry all parts thoroughly.

Never place hot or warm foods into the cabinet or leave the doors open for longer than

necessary as this will raise the temperature and cause excessive amounts of moisture thus

increasing the amount of ice in the refrigerator / freezer compartment.

The Internal Light

The internal light will automatically switch ON and OFF whenever the refrigerator door

is opened or closed. To change the light bulb, please see the chapter on changing the light

bulb.

To obtain a lower internal temperature turn the thermostat temperature control to a

higher number. To obtain a higher internal temperature turn the thermostat control

to a lower number. However, the internal temperature and temperature control

setting is dependent on a number of factors:

1. Varying ambient temperatures.

2. The number of times the appliance doors are opened and how long the doors remain

open.

3. The amount and temperature of the food and drink introduced into the appliance.

4. The weather conditions and time of year e.g. summer / winter.

5. The positioning of the appliance and an adequate air circulation to the sides and

back of the cabinet.

To enable adjustment of the temperature in the appliance it is fitted with an adjustable

thermostat located in the fridge compartment, which can be adjusted from setting 1

(warmest) to 7 (coldest). For normal working temperature it is recommended to adjust

the thermostat control to the midway position, after a few hours readjust the thermostat

to the desired temperature. There is also an off position 0 . Which turns OFF the

refrigerator and freezer compartments. Please Note this dose not disconnect the

appliance from the mains supply. To do this you must remove the mains plug from the

socket.

6

Making ice cubes

( Ice tray not supplied )

Pour water into the ice cube tray until it is two thirds full and place into the freezer. Ice

cubes will form in approximately 2 to 3 hours. The ice cube can be easily removed by

twisting the ice cube tray or running under cold water for a short time.

Freezing fresh food (Freezer)

Ensure that your freezing operations are carried out under the most hygienic conditions,

as freezing alone does not sterilize the food. Never put hot or even warm foodstuffs into

the freezer. Prior to storing the food, pack it in plastic bags, aluminum foil or freezer

containers and place into the freezer without putting them in contact with food that has

already been frozen. See the technical data sheet at the rear of this booklet for the

maximum permissible amount in kilograms of fresh food that can be frozen in any 24

hour period with a room temperature of 25C. Never freeze more than the maximum

permissible.

Store frozen food

When using the freezer for the first time or after defrosting, turn the thermostat

temperature control to setting 7 for at least two hours before introducing the food to be

stored, Then adjust to your preferred setting.

All frozen food products you purchase should be placed in the freezer as soon as

possible to avoid the frozen food from defrosting.

Storage recommendations printed on the packaging of frozen food by the

manufactures should always be followed.

Storage of fresh food in the refrigerator

Food should always be covered tightly with foil, plastic film, placed in bags or stored in

airtight containers. This will prevent food from dehydrating and prevent the strong smell

of some foods transferring to milder ones.

To store raw meat wrap in polythene bags or airtight containers and place on the

lowest shelf.

Do not allow raw meat to come into contact with cooked foods. For safety, only store raw

meat for two or three days. Fruit and vegetables should be thoroughly cleaned and

placed in the vegetable/ salad bin.

Milk and other liquids should be sealed with lids and placed in the bottle shelf on the

door.

Refrigerator defrost process

The refrigerator defrosting process is carried out automatically every time the

compressor stops.

The defrost water drains from the cabinet into a tray placed on the top of the

compressor to the rear of the unit where it evaporates.

Freezer defrost process

Small amounts of frost will accumulate inside th

e freezer depending upon the

length of time during which the door is left open or the amount of moisture

introduced. It is essential to ensure that no frost or ice is allowed to form at places

where it will affect the close fitting of the door seal. This might allow air to

penetrate the cabinet, thus encouraging continuous running of the compressor. Thin

frost formation is quite soft and can be removed with a brush or plastic scraper. Do

not use metal or sharp scrapers, mechanical devices or other means to accelerate the

defrosting process. Remove all dislodged frost from the cabinet floor .For the

removal of thin frost it is not necessary to switch off the appliance.

For the removal of heavy ice deposits disconnect the appliance from the mains

supply and empty the contents into cardboard boxes and wrap in thick blankets or

layers of paper to keep them cold. Defrosting will be most effective if carried out

when the freezer is empty, and place a pan of hot water on one of the shelves and

close the door for faster defrosting. Do not forget to put a container under the front

of the freezer cavity to catch the water as the ice melts.

An increase in temperature of frozen food packages du

ring defrosting will shorten

the storage life. Provided that the contents are well wrapped and placed in a cool area

they should keep for several hours.

Examine the contents when replacing them in the freezer and if some of the

packages have thawed out it should be eaten within 24hours or be cooked and refrozen.

After defrosting has finished clean the inside with a solution of warm water with a

little bicarbonate of soda and then dry thoroughly. Wash all removable parts in the

same way and reassemble. Reconnect the appliance to the mains supply and leave

for 2 to 3 hours on setting number 7 before introducing the food back into the

freezer and setting the thermostat to your normal setting(usually setting 4).

7

8

Power Failure

If there is a power failure for a short time less than 12 hrs keep the door closed

Frozen food should not be affected if the failure lasts for less than 12 hrs.

Extra protection can be given by covering the appliance with two or three thick blankets.

If a long power failure is anticipated, try to get the foodstuff into another appliance or

cold store, if possible.

Prolonged off periods

If the power cut is longer than 12 hrs then check the content of the freezer.

If the food has defrosted, cook and refreeze the food or it should be eaten immediately.

Never refreeze food that has been defrosted.

Disconnect the appliance from the mains supply.

Pull the lamp cover forwards, to gain accesses to the lamp . Unscrew the light

bulb in an anti-clockwise direction from the holder.

Replace the bulb with one of the correct type and size (10 watt E14 base).

Replace the cover by Pushing the cover Backwards.

Reconnect the appliance to the mains supply.

Changing the light bulb

Note. Light bulbs are not covered by the warranty

If the appliance is not to be used for a long period of time then it is recommended to

remove all the food stuff, clean the inside of the appliance and leave the door open to

allow the air to circulate thus avoiding unpleasant odors.

Cleaning and maintenance

Before any cleaning or maintenance is carried out you must disconnect the appliance

from the mains supply by removing the plug, never remove the plug by pulling on the

mains cord. Remove the plug by pulling on the plug itself.

It is recommended that when cleaning the appliance, both the inside and outside, can be

cleaned using warm water and a little bicarbonate of soda. Use 1 teaspoon to 1.2 litres

of water.

If the appliance is not operating correctly:

Please check the following points.

Is there a power failure? (Check by turning on a house light)

Has the fuse blown or has the circuit breaker tripped.

Has the door been closed correctly?

Check the thermostat has been set correctly.

Check the mains plug is seated in the wall socket correctly and the socket switch is on.

Check the power outlet is working, Try another appliance.

Is the room temperature too cold or too hot. ( working temperature range 16 to 32 )

If the appliance is not used for a prolonged period

If the refrigerator is not in use for a long period of time, proceed as follows:

Disconnect the refrigerator from the main supply by removing the plug from the socket.

Clean and dry the inside as instructed under the heading of cleaning the appliance.

Leave the door open to prevent any unpleasant smells from building up while the

appliance is not in use.

Before calling for service

Please check the following points:

1. The refrigerator is not working

Check the plug is inserted correctly into the wall socket

Check there is power to the wall socket by plugging in another appliance, if the other

appliance works, check the fuse in the appliance plug.

2. The refrigerator is noisy when running

Check the appliance is level and is not in contact with another appliance or kitchen

furniture.

3. The refrigerator does not cool sufficiently.

If the door has been opened too often, or it has been left open for a while it will take

time for the appliance to reach its set temperature.

Check the air flow around the refrigerator has not been reduced due to insufficient

clearance.

NOTE: The following characteristics should not be looked upon as a problem.

A gentle trickling sound caused by coolant flowing through the pipe.

Compressor operating at high temperature.

9

10

Don't- Cover the shelves with any protective materials which may obstruct air circulation.

Don't- Store poisonous or any dangerous substances in your fridge. It has been

designed for the storage of edible foodstuffs only.

Don't- Consume food which has been refrigerated for an excessive length of time.

Don't- Store cooked and fresh food together in the same container. They should be

packaged and stored separately.

Don't- Let defrosting food or food juices drip onto already stored food.

Don't- leave the door open for long periods, as this will make the appliance more costly

to run and cause excessive ice formation.

Don't- Use sharp edged objects such as knives or forks to remove the ice.

Don't- Use hairdryers, or electrical appliances for defrosting only use item

recommended by the manufacturer.

Don't- put hot food into the appliance. Let it cool down first.

Don't- put liquid-filled bottles or sealed cans containing carbonated liquids into the

freezer section, as they may burst.

Don't- Give children ice cream and water ices direct from the freezer section. The low

temperature may cause 'freezer burns' on the lips.

Don't- Try to keep frozen food which has thawed; it should be eaten within 24 hours or

cooked and refrozen.

Don't- Damage the refrigerant circuit at any time

Do's and Don'ts

Do- keep raw meat and poultry below cooked food and dairy products.

Do- Leave lettuce, cabbage, parsley and cauliflower on the stem.

Do- Wrap cheese firstly in greaseproof paper and then in a polythene bag, excluding As

much air as possible. For best results, take out of the fridge compartment an hour before

eating.

Do- Wrap raw meat and poultry loosely in polythene or aluminium foil. This prevents

drying.

Do- Wrap fish and offal in polythene bags.

Do- Wrap food with a strong odour or which may dry out, in polythene bags, or

aluminium foil or place in airtight container.

Do- Wrap bread well to keep it fresh.

Do- Chill white wines, beer, larger and mineral water before serving.

Do- Check contents of the low temp compartment every so often.

Do- Keep food for as short a time as possible and adhere to "Best before" and "Use by"

etc. dates.

Do- Store commercially prepared food in accordance with the instructions given on the

packets.

Do- Always choose high quality fresh food and be sure it is thoroughly clean before

Storing it.

Do- Wrap all food in aluminium foil or food quality polythene bags and make sure any

air is excluded.

Do-Keep ventilation openings, in the appliance enclosure clear of obstruction.

Do-ensure that frozen food does not rise in temperature while defrosting, a rise in

temperature during defrosting may shorten the storage life of your food.

Product Features:

Total Storage volume : 210 L

Energy class : A+

Energy consumption : 212 kWh / year

Climate class : N

Adjustable thermostat

Reversible doors, external handles

2 front adjustable feet

Colour: White

Refrigerant: R-600A

Max noise level: 42dB

Length of cable : 1.4 meters

Refrigerator : 170 L

3 glass shelves

1 transparent crisper

2+4 transparent balconies

Automatical defrosting

Freezer: 40 L

Freezing capacity : 2.0 kg / 24 h

Max storage time by power failure : 12 h

1 wire shelf

Manual defrosting

Dimensions :

Product H x W x D (cm): 143 x 55 x 58

Packing H x W x D (cm): 148 x 57 x 60

Net weight / Gross weight : 45 kg / 49 kg

Power :

Voltage/ frequency : 220-240V~/50Hz

Fridge-Freezer HRFZ-250D/U

49m

547mm

1083mm

516mm

1000mm

2

22

11

IMPORTANT DISPOSAL INSTRUCTIONS

As a responsible retailer we care about the environment.

As such we urge you to follow the correct disposal procedure for your product

and packaging materials. This will help conserve natural recourses

and ensure that it is recycled in a manner that protects health and the

environment.

You must dispose of this product and its packaging according to local laws

and regulations. Because this product contains electronic components and

sometimes batteries, the product and its accessories must be disposed of

separately from household waste when the product reaches its end of life.

Contact your local authority to learn about disposal and recycling.

The product should be taken to your local collection point for recycling.

Some collection points accept products free of charge.

We apologise for any inconvenice caused by minor inconsistencies in these instructions,

which may occur as a result of product improvement and development.

12

HRFZ-250D AA

RÉFRIGÉRATEUR-

CONGÉLATEUR

MODE D’EMPLOI

Désignation des pièces

○1 Couvercle supérieur

○2 Grille

○3 Groupe thermostat et ampoule

○4 Interrupteur de la porte

○5 Clayettes en verre

○6 Couvercle du bac à légumes

○7 Bac à légumes

○8 Pieds avant réglables

○9 Balconnets de porte

○10 Joint de la porte du réfrigérateur

○11 Porte du congélateur

1

Merci d’avoir acheté ce réfrigérateur-congélateur Haier. Pour une utilisation optimale

de votre nouveau congélateur, prenez quelques instants pour lire les instructions

simples de ce manuel.

Vérifiez que l’emballage peut se jeter conformément aux exigences

environnementales actuelles.

Si l’appareil présente un dommage visible, ne le branchez pas et contactez le

magasin où vous l’avez acheté.

BRANCHEMENT ÉLECTRIQUE ROYAUME-UNI UNIQUEMENT

Pour votre sécurité, veuillez lire les informations suivantes

Attention Cet appareil doit être mis à la terre.

Cet appareil fonctionne avec une tension de 220 à 240 volts et doit être protégé par

un fusible de 13 ampères intégré dans la prise.

L’appareil est livré avec une prise standard à 3 broches de 13 ampères dotée d’un

fusible de 13 ampères.

Si nécessaire, remplacez le fusible par un autre fusible de 13 ampères approuvé par

la norme BS1362.

Si la prise principale n’est pas adaptée à la prise murale de votre domicile ou si elle

est retirée pour toute autre raison, suivez les instructions sur le branchement d’une

prise à 3 broches de 13 ampères ci-dessous.

Branchement d’une prise de 13 ampères.

Important. Les fils du câble principal de cet appareil présentent des couleurs qui

correspondent au code suivant :

Vert et jaune - Terre

Bleu - Neutre Marron

- Phase

Étant donné que les couleurs risquent de ne pas

correspondre au marquage d’identification des

bornes de votre prise, procédez comme suit : le fil

Vert et Jaune doit être branché sur la borne de la

prise présentant la lettre E ou le symbole de terre ^

ou de couleur verte et jaune.

Le fil Bleu doit être branché sur la borne présentant

la lettre N ou de couleur noire.

Le fil Marron doit être branché sur la borne présentant la lettre L ou de couleur

rouge.

Vérifiez que le câble principal est maintenu en toute sécurité par le serre-câble.

2

MERCI D’AVOIR ACHETÉ CE PRODUIT HAIER

Ce manuel contient les informations nécessaires à l’installation et au

fonctionnement de votre nouvel appareil.

Il est important et utile de prendre quelques instants pour lire entièrement ce

manuel afin de comprendre le fonctionnement sûr et efficace de l'appareil.

Gardez ce manuel en lieu sûr pour pouvoir vous y reporter si nécessaire.

Informations sur la sécurité

Ces informations sont fournies dans l’intérêt de votre sécurité. Veuillez lire

attentivement ce qui suit avant de procéder à l’installation ou à l’utilisation de

l’appareil.

Si vous vous débarrassez d'un ancien congélateur ou réfrigérateur doté d’un

verrou / fermeture fixé sur la porte, vérifiez qu’il soit laissé en toute sécurité

afin d’éviter que les enfants s’y prenne au piège en jouant.

Étant donné que les anciens appareils de réfrigération peuvent contenir du CFC

nocif pour la couche d’ozone, avant de traiter tout appareil de réfrigération,

contactez votre service local de ramassage des ordures pour vous renseigner

sur le bon traitement de l’appareil.

Cet appareil sert uniquement à la congélation et au stockage de nourriture

comestible domestique et ne doit pas être utilisé à d’autres fins.

Si le câble principal est endommagé, faites-le remplacer par le fabricant, son

agent de maintenance ou une personne qualifiée afin d'éviter tout danger.

Installation

Placez l’appareil et laissez-le en position verticale pendant deux à trois heures

avant de l’allumer pour la première fois afin que le système se stabilise. Ne

placez pas l’appareil à proximité d’une source de chaleur comme une cuisinière,

une chaudière ou en contact direct avec la lumière du soleil, etc.

Laissez un espacement de 10 cm des deux côtés de l’appareil et de tout autre

meuble ou mur adjacent afin de permettre une bonne circulation de l’air.

L’appareil n’est pas conçu pour une installation encastrée.

Installez l’appareil sur une surface stable et plane. Toute inégalité du sol doit

être corrigée avant l’installation ; les légères inégalités peuvent être gommées en

réglant les pieds avant.

REMARQUE : si l’appareil est placé sur de la moquette, un tapis ou un

revêtement de sol souple, réglez de nouveau les pieds avant une fois que

l’appareil ait eu le temps de s’installer.

3

INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ

Cet appareil doit être utilisé avec la tension électrique indiquée sur sa plaque

signalétique ; toute utilisation avec une autre tension ANNULERA la garantie

et risque d’endommager le produit.

Cet appareil est conçu pour une utilisation domestique uniquement, toute

autre utilisation risque d'annuler la garantie et d'être dangereuse.

Cet appareil doit être utilisé à l'intérieur uniquement et non en extérieur.

Les surfaces accessibles risquent de chauffer durant le fonctionnement,

utilisez toujours les poignées et les boutons.

Pour éviter toute électrocution, n’immergez ni le câble, ni les prises ni

l’appareil dans de l’eau ou tout autre liquide.

Ne tentez pas de déplacer la nourriture lorsque l’appareil fonctionne.

Débranchez l’appareil de la prise lorsque vous ne l’utilisez pas et avant de le

nettoyer. Retirez la nourriture avant de nettoyer l’appareil.

Si le câble principal est endommagé, faites-le remplacer par le fabricant, son

agent de maintenance ou une personne qualifiée afin d'éviter tout danger.

Ne faites pas fonctionner l’appareil si le câble ou la prise est endommagé(e), si

l’appareil présente des dysfonctionnements ou s’il a été endommagé.

Contactez le magasin où vous l’avez acheté pour obtenir un conseil.

Le circuit de refroidissement de l’appareil ne doit pas être endommagé.

Ne rangez pas de la nourriture de trop grande dimension car cela risque

d'entraîner un danger.

Ne laissez pas le câble pendre par-dessus le bord de la surface ni toucher les

surfaces chaudes.

Ne placez pas l’appareil sur ou à proximité de surfaces chaudes ou en contact

direct avec la lumière du soleil.

Soyez extrêmement vigilant(e) lorsque vous déplacez l’appareil.

Commencez toujours par brancher le câble sur l’appareil puis le câble sur la

prise murale. Pour débrancher l’appareil, mettez l’interrupteur sur ARRÊT puis

retirez la fiche de la prise murale.

Un petit câble d’alimentation est fourni afin de réduire le risque de

trébuchement.

4

Utilisation de l’appareil

Retirez l’emballage et nettoyez l’intérieur de l’appareil avec de l’eau tiède

ajoutée à un peu de bicarbonate de soude (1 cuillère à café pour 1,2 litre

d’eau). N’utilisez ni détergent ni savon car ils risquent de gâter la

nourriture. Après le nettoyage, essuyez toutes les pièces correctement.

Commande de température

Le réfrigérateur est conçu pour maintenir une température de

stockage interne dans le compartiment réfrigération comprise

entre 0°C et + 10°C.

Pour régler la température interne, cet appareil est doté d’un thermostat

dans le compartiment du réfrigérateur ; le thermostat peut-être réglé de 1

(température la plus chaude) à 7 (température la plus froide). Pour une

température normale de fonctionnement, nous vous recommandons de

régler la commande du thermostat sur la position du milieu ; après

quelques heures, réglez de nouveau le thermostat sur la température

souhaitée. Il existe également une position arrêt « 0 » qui permet

d’ÉTEINDRE les compartiments du réfrigérateur et du congélateur.

Notez que celui-ci ne débranche pas l’appareil de l’alimentation

principale. Pour ce faire, vous devez retirer la fiche principale de la prise

murale.

Pour obtenir une température interne inférieure, tournez la

commande de température du thermostat dans le sens des aiguilles

d’une montre vers un chiffre plus grand. Pour obtenir une

température interne supérieure, tournez la commande de

température du thermostat dans le sens inverse des aiguilles d’une

montre vers un chiffre plus petit. Cependant, la température interne

et le réglage de la commande de température dépend d’un certain

nombre de facteurs :

1. Les variations de température ambiante.

2. Le nombre de fois que les portes de l’appareil sont ouvertes et le

temps d’ouverture de ces portes.

3. La quantité et la température de la nourriture et des boissons

introduites dans l’appareil.

4. Les conditions climatiques et la période de l’année (été/hiver).

1. L’emplacement de l’appareil et une bonne circulation de l’air sur les

côtés et l’arrière de l’appareil.

Ne placez jamais de la nourriture chaude ou tiède dans l’appareil et ne

laissez pas les portes trop longtemps ouvertes car cela entraîne une

hausse de la température et des excès d’humidité augmentant ainsi la

quantité de glace dans le compartiment réfrigérateur / congélateur.

Éclairage intérieur

L’éclairage intérieur s’ALLUME et s’ÉTEINT automatiquement à

l’ouverture et à la fermeture de la porte du réfrigérateur. Pour remplacer

l’ampoule, consultez le paragraphe correspondant.

5

Stránka se načítá ...

Haier HRFZ-250D Uživatelský manuál

Haier HRFZ-250D Uživatelský manuál

v jiných jazycích

Související papíry

Jiné dokumenty