ABB PowerValue 11 RT Quick Manual



l

�



un I Jet

, 

ИБ

П ABB Powervalue 11 RT (6-10 кВА) - руководство по эксплуатации. Юниджет

Постоянная ссылка на страницу: https://www.uni-jet.com/catalog/istochniki-

besperebojnogo-pitaniya/on-line-ibp-1-kva-10kva/abb-powervalue-11-rt.html

PowerValue 11 RT

6-10 kVA

Quick guide

Quick guide | PowerValue 11 RT 6-10 kVA 1

1

2

3

2 PowerValue 11 RT 6-10 kVA | Quick guide

4

5

Quick guide | PowerValue 11 RT 6-10 kVA 3

6

7

4 PowerValue 11 RT 6-10 kVA | Quick guide

Quick guide | PowerValue 11 RT 6-10 kVA 5

1en

es

da

zh

fr

ﬁ

ru

nl

de

pt

cz

el

it

sv

pl

PowerValue 11 RT 6-10 kVA

Quick guide 7

Kurzanleitung 21

Guide de référence rapide 35

Guida rapida 49

Guía rápida 63

Guia de consulta rápida 77

Pikaopas 91

Snabbinstruktion 105

Kvikguide 119

Rychlý průvodce 133

Краткое руководство 147

Skrócony podręcznik 161

速成指南 175

Σύντομος οδηγός 189

Beknopte installatiehandleiding 203

6 PowerValue 11 RT 6-10 kVA | Quick guide

Quick guide | PowerValue 11 RT 6-10 kVA 7

1en

PowerValue 11 RT 6-10 kVA

Quick guide

Safety instructions 8

Installation 13

Operation 15

Troubleshooting 17

8 PowerValue 11 RT 6-10 kVA | Quick guide

en

Safety instructions

Read carefully

Always follow the precautions and instructions described in this manual. Any

deviations from the instructions may result in electrical shock or cause accidental

load loss.

ABB DOES NOT TAKE ANY RESPONSIBILITY FOR DAMAGES CAUSED THROUGH INCORRECT

MANIPULATIONS OF THE UPS SYSTEM.

Safety notices

WARNING

WARNING INDICATES THE PRESENCE OF A HAZARD WHICH COULD

RESULT IN SEVERE INJURY AND/OR SERIOUS DAMAGE TO THE SYSTEM.

CAUTION

CAUTION INDICATES THE PRESENCE OF A HAZARD WHICH COULD

RESULT IN MINOR INJURY AND/OR DAMAGE TO THE PRODUCT.

NOTE

NOTE INDICATES THE PRESENCE OF A HAZARD WHICH COULD LEAD TO

PROPERTY DAMAGE.

Safety symbols

SAFETY WARNING: THE SYMBOL IS USED TO ALERT THE USER TO WARNINGS,

CAUTIONS AND NOTES.

DANGER: THE SYMBOL IS USED TO ALERT THE USER TO THE OCCURRENCE

OF ELECTRICAL LIVE PARTS WITH HAZARDOUS VOLTAGES.

Quick guide | PowerValue 11 RT 6-10 kVA 9

1en

Batteries

DANGER

WARNING

COMPONENTS INSIDE THE UPS ARE CONNECTED TO THE

BATTERY EVEN WHEN THE UPS IS DISCONNECTED FROM

THE MAINS POWER SUPPLY.

DANGER

WARNING

DISCONNECT THE BATTERIES BEFORE CARRYING OUT ANY

KIND OF SERVICE AND/OR MAINTENANCE. VERIFY THAT NO

CURRENT IS PRESENT AND NO HAZARDOUS VOLTAGE

EXISTS IN THE CAPACITOR OR BUS CAPACITOR TERMINALS.

DANGER

WARNING

A BATTERY CAN PRESENT A RISK OF ELECTRICAL SHOCK

AND HIGH SHORT CIRCUIT CURRENT. THE FOLLOWING

PRECAUTIONS MUST BE OBSERVED WHEN WORKING ON

BATTERIES:

• REMOVE WATCHES, RINGS OR OTHER METAL OBJECTS

• MAKE USE OF PROPER PPE (PERSONAL PROTECTION

EQUIPMENT) AS PER LOCAL POLICIES AND RULES

— WEAR FLAME/ARC RESISTANT WHOLE BODY

CLOTHING

— WEAR SUITABLE VOLTAGE RATED GLOVES

— USE SAFETY DIELECTRIC FOOTWEAR

— WEAR ARC FLASH FACE SHIELD

— USE VOLTAGE RATED TOOLS

• DO NOT LAY TOOLS OR METAL PARTS ON TOP OF

BATTERIES

• DISCONNECT THE CHARGING SOURCE PRIOR TO

CONNECTING OR DISCONNECTING BATTERY TERMINALS.

DANGER

WARNING

THE BATTERY CIRCUIT IS NOT ISOLATED FROM THE INPUT

VOLTAGE. HAZARDOUS VOLTAGES MAY OCCUR BETWEEN

THE BATTERY TERMINALS AND THE GROUND. VERIFY THAT

NO VOLTAGE IS PRESENT BEFORE SERVICING.

WARNING

NEVER DISPOSE BATTERIES ON FIRE AS THEY MAY EXPLODE.

10 PowerValue 11 RT 6-10 kVA | Quick guide

en

WARNING

DO NOT OPEN OR MUTILATE THE BATTERIES.

WARNING

RELEASED ELECTROLYTE IS HARMFUL TO THE SKIN AND EYES.

CAUTION

REPLACE BATTERIES WITH THE SAME NUMBER AND SAME TYPE OF

BATTERIES.

Installation

DANGER

WARNING

DISPLAY A WARNING LABEL ON ALL PRIMARY POWER

ISOLATORS INSTALLED REMOTE FROM THE UPS AREA TO

WARN ELECTRICAL MAINTENANCE PERSONNELS THAT THE

CIRCUIT FEEDS A UPS.

MAKE SURE THAT WARNING LABEL CONTAINS THE

FOLLOWING TEXT OR EQUIVALENT: “ISOLATE THE UPS

(UNINTERRUPTIBLE POWER SUPPLY) BEFORE WORKING ON

THIS CIRCUIT”.

DANGER

WARNING

HIGH FAULT CURRENTS (LEAKAGE CURRENTS). BEFORE

CONNECTING THE MAINS ENSURE THAT THE UPS IS

GROUNDED!

DANGER

WARNING

DO NOT REMOVE ANY SCREWS FROM THE UPS SYSTEM OR

FROM THE BATTERY CABINET: DANGER OF ELECTRICAL

SHOCK.

Quick guide | PowerValue 11 RT 6-10 kVA 11

1en

DANGER

WARNING

WHEN OPENING OR REMOVING THE UPS-COVERS YOU ARE

EXPOSED TO DANGEROUS VOLTAGES.

DANGER

WARNING

RISK OF BACKFEED VOLTAGE, ISOLATE THE UPS INSTALLING

AN EXTERNAL ISOLATING DEVICE BETWEEN MAINS INPUT

AND UPS; BEFORE OPERATING ON THIS CIRCUIT, CHECK

FOR HAZARDOUS VOLTAGE.

WARNING

WATER CONDENSING MAY OCCUR IF THE UPS IS UNPACKED IN A VERY

LOW TEMPERATURE. IN THIS CASE IT IS NECESSARY TO WAIT UNTIL THE

UPS IS FULLY DRIED INSIDE OUT BEFORE PROCEEDING INSTALLATION

AND USE TO AVOID HAZARDS AND ELECTRIC SHOCK, WAIT UNTIL THE

UPS IS FULLY DRY BOTH INSIDE AND OUTSIDE BEFORE INSTALLING.

CAUTION

INDUCTIVE LOADS (FOR EXAMPLE MONITORS AND LASER PRINTERS)

HAVE A VERY HIGH POWER CONSUMPTION AT START-UP. IF CONNECTED

TO THE UPS, THE START-UP POWER OF SUCH LOADS MUST BE TAKEN

INTO CONSIDERATION WHEN CALCULATING THE CAPACITY OF THE UPS

TO PREVENT THE UPS FROM BEING OVERLOADED AND TURNED OFF.

NOTE

TO REDUCE THE RISK OF FIRE, CONNECT THE UPS TO A CIRCUIT

PROVIDED WITH BRANCH CIRCUIT OVERCURRENT PROTECTION WITH AN

AMPERE RATING IN ACCORDANCE WITH THE IEC/EN 60934 STANDARD OR

YOUR LOCAL ELECTRICAL CODE.

SEE TECHNICAL SPECIFICATIONS FOR RECOMMENDATIONS.

12 PowerValue 11 RT 6-10 kVA | Quick guide

en

Operation

CAUTION

DO NOT OPERATE IN CASE OF PRESENCE OF WATER OR MOISTURE.

CAUTION

DO NOT DISCONNECT THE MAINS CABLE FROM THE UPS OR THE

BUILDING WIRING SOCKET DURING OPERATION AS THIS REMOVES THE

GROUND FROM THE UPS AND ALL CONNECTED LOADS.

CAUTION

SWITCH OFF THE CONNECTED LOADS BEFORE TURNING ON THE UPS.

THEN SWITCH ON THE LOADS ONE BY ONE AFTER THE UPS IS TURNED

ON. SWITCH OFF ALL OF THE CONNECTED LOADS BEFORE TURNING OFF

THE UPS.

CAUTION

REPLACE FUSES ONLY BY DEVICES OF THE SAME TYPE AND OF THE

SAME AMPERAGE TO AVOID FIRE HAZARDS.

NOTE

PRESS THE OFF BUTTON TO FULLY DISCONNECT THE UPS. WAIT UNTIL

THE UPS IS ON BYPASS OR ON STAND-BY MODE BEFORE

DISCONNECTING IT FROM THE MAINS.

NOTE

INDISCRIMINATE OPERATION OF SWITCHES MAY CAUSE OUTPUT LOSS OR

DAMAGE TO EQUIPMENT.

Quick guide | PowerValue 11 RT 6-10 kVA 13

1en

Installation

Planning before installation

Install the unit to a position where any danger to the UPS is minimized to ensure a

long service life:

• Install the UPS indoors.

• Leave 50cm of space on each side of the cabinet to enable cooling airflow and

ensure that the circulation of air to the ventilation slits is not obstructed.

• Avoid excessively high temperature and excessive moisture

• Make sure that the surface is solid and flat

Rack mount installation – requires rack mounting kit, to be purchased

separately

• Identify the rail holes in the rack for positioning the cabinet. Position the rails in

the bottom of the 3U space for 6kVA units and 5U space for 10kVA units.

• Slide the cabinet into the rack. (Fig.1)

• If installing additional UPS units, repeat the steps above for each cabinet

Tower installation

PowerValue 11 RT 6 kVA

• Carefully rotate the LCD control panel 90º to the right. (Fig.2)

• Place the units to a vertical position.

• Screw the supports to the sides of the unit. (Fig.3)

PowerValue 11 RT 10 kVA

• Carefully rotate the LCD control panel 90º to the right in the top and bottom front

panels. (Fig.4)

• Place the units to a vertical position.

• Screw the supports to the sides of the unit. (Fig.5)

14 PowerValue 11 RT 6-10 kVA | Quick guide

en

Electrical connections

• PowerValue 11 RT 6 kVA (see Fig.6)

Legend

1 GND contact

2 EPO

3 Parallel port

4 Output circuit breaker

5 Output sockets

6 SNMP/ AS400 slot

7 USB

8 RS232

9 Bypass

10 AC input

11 AC output

• PowerValue 11 RT 10 kVA (see Fig.7)

Legend

1 SNMP/ AS400 slot

2 EPO

3 USB

4 Parallel port

5 Battery connector

6 GND contact

7 Output sockets

8 Output circuit breaker

9 AC output

10 Bypass

11 AC input

Quick guide | PowerValue 11 RT 6-10 kVA 15

1en

Operation

You can operate the UPS through the user-friendly display (see chapter 4 of the user

manual for a full list of possible operations).

Power on/off

Scroll up

Scroll down

Select / Edit

UPS start-up

To start up the UPS with mains supply:

1. Check that all cables are connected correctly and well-fixed mechanically.

2. Keep the power-on button pressed for longer than 1 second. The fans are

activated and the UPS will load for a few seconds.

3. The UPS performs a self-test and the LCD shows the default UPS status screen.

16 PowerValue 11 RT 6-10 kVA | Quick guide

en

To start up the UPS without mains supply (cold start):

1. Check that all cables are connected correctly and well-fixed mechanically.

2. Keep the power-on button pressed for longer than 1 second. The UPS is powered

on, the fans are activated and the LCD is turned on. The UPS performs a self-test

and shows the default UPS status screen.

3. Keep the power-on button pressed for longer than 1 second. The alarm buzzer

sounds for 1 second and the UPS starts up.

4. After a few seconds, the UPS transfers to battery-mode. When the UPS is

supplied with power from the mains, the UPS transfers to online-mode without

interruption in the output of the UPS.

UPS Shutdown

To shut down the UPS with mains supply:

1. If the UPS is working on bypass-mode, go to step 3.

2. If the UPS is on online-mode, keep the power-on button pressed for more than 3

seconds. The alarm buzzer will sound and the UPS will transfer to bypass-mode.

Note that the bypass is still energized.

3. Disconnect the mains power supply. The display will shut down and the output

voltage will be removed from the UPS output terminal.

4. In case bypass has been disabled through the Settings menu, keep the power-

on button pressed for longer than 3 seconds to shut down the UPS. The unit will

transfer from online to stand-by mode. Disconnect the input power cable and the

display will shut down.

To shut down the UPS without mains supply:

1. To power off the UPS, keep the power on/off button pressed for more than 3

seconds. The alarm buzzer will sound for 3 seconds and the output power will be

immediately cut-off.

2. The display will shut down and the output voltage will be removed from the UPS

output terminal.

Quick guide | PowerValue 11 RT 6-10 kVA 17

1en

Troubleshooting

Alarm and events indicate warnings and notify of errors or potential failures in the

system. The output of the UPS is not necessarily affected in case of an alarm but

taking the correct actions may prevent loss of power to the load. If the UPS system

does not operate correctly, attempt to solve the problem using the table below.

Alarm or Event Possible cause Remedy

Utility Abnormal

Alarm Code: 02

The input mains is out of the UPS

tolerance range

Check input mains condition

Site Wiring Fault

Alarm Code: 04

Site Fault detection is supported on

all-models when a Grounding Neutral

connection is present. Alarm will

trigger when the difference between

ground and neutral voltage is >15V.

Site Fault detection should be

enabled by default. It can be enabled

/ disabled from the LCD settings

menu.

Reconnect all input wires

Battery Disconnect

Alarm Code:11

Battery voltage is lower than the

batteries disconnected level defined

for this UPS. There could be a blown

fuse, intermittent battery connection

or disconnected battery cable.

Verify that all batteries are properly

connected.

If the condition persists, contact your

service representative.

Battery low

Alarm Code:12

The UPS is in battery-mode and the

battery autonomy is running low.

This warning is approximate and the

actual time to shut down may vary.

Depending on the UPS load and the

number of external battery modules

(EXBAT), the “Battery Low” warning

may occur before the batteries reach

25% capacity

Service Battery

Alarm Code:13

A battery string failure has been

detected and the battery charger has

been disabled until its replacement

Contact your service representative

Charger Fail

Alarm Code:15

Indicates a charger failure The UPS charger is turned off until

the next startup. Contact your

service representative

Battery Over Voltage

Alarm Code:16

Indicates that the battery voltage is

too high

The UPS will turn off the charger until

the battery voltage is normal

BUS Over Voltage

Alarm Code:21

Indicates an over voltage in the BUS

of the UPS.

The UPS transfers to Bypass-mode

if supporting the load

BUS Under Voltage

Alarm Code:22

Indicates an under voltage in the

BUS of the UPS.

The UPS transfers to Bypass-mode

if supporting the load

BUS Unbalance

Alarm Code:23

Indicates that the positive BUS

voltage and negative BUS voltage

are not symmetric

The UPS transfers to Bypass-mode

if supporting the load

Stránka se načítá ...

ABB PowerValue 11 RT Quick Manual

ABB PowerValue 11 RT Quick Manual

v jiných jazycích

Související papíry

Jiné dokumenty