Vestfrost FZ Series Instructions For Use & Warranty

FZ ... W

ES Instrucciones para el uso

CZ Návod k použití

PL Instrukcja obsługi

IT I Istruzioni per l’uso

RUS Инструкция к применению

UK Instructions for use

DE Bedienungsanleitung

FR Mode d’emploi

DK Brugsanvisning

NO Bruksanvisning

NL Gebruiksaanwijzing

2

GB

Thank you for purchasing your new wine

cooler from Vestfrost. Please note that

these instructions apply to all wine coolers

in the FZ range. Illustrations and ttings

may therefore not necessarily correspond

exactly to your model.

Warning

WARNING: - keep ventilation openings, in

the appliance enclosure or in the built-in

structure, clear of obstruction.

WARNING: - do not use mechanical

devices or other means to accelerate the

defrosting process, othet than those recom-

mended by the manufacturer,

WARNING: - do not damage the refrigerant

system.

WARNING: - do not use electrical ap-

pliances inside the refrigerated storage

compartments, unless they are of the type

recommended by the manufacturer.

The appliance shall not be exposed to rain.

* Keep always the keys in separate place

and out of reach of children.

* Before servicing or cleaning the appliance,

unplug it from the mains.

As the appliance contain a refrigerant which

is ammable (Isobutane R600a) it is essen-

tial to ensure that the refrigerant pipes are

not damaged.

If damage does occur, avoid sparks or

naked ame in the vicinity of the appliance,

ensure that the room is well ventilated,

disconnect the power supply, and contact

your supplier.

The unit must only be serviced by quali-

ed technicians from an approved service

centre.

This appliance is not intended for use by

young children or inrm persons unless

they have been adequately supervised by a

responsible person to ensure that they can

use the appliance safely”.

“Young children should be supervised to

ensure that they do not play with the appli-

ance”.

Old appliances

Old refrigerators and freezers are often

tted with complicated latches that can

only be opened from the outside. If you

have one of these old units stored away

somewhere, or if you scrap one, remember

to destroy the latch rst in order to prevent

children from being exposed to great dan-

ger by getting locked inside the unit.

Contents

Get to know your wine cooler...........3

Installation and start-up....................4

Reversible door.................................7

Electrical connection.........................8

Operation and function.....................9

Defrosting,

cleaning and maintenance..............11

Fault nding....................................12

Warranty, spare parts and service..13

Disposal..........................................14

3

GB

Get to know your wine cooler

g.1

Lighting

Charcoal lter

Wooden shelf

Sealing strip

Nameplate

Door handle

Kick plate

Control panel

Lock

Adjustable feet

Before use

Before operating your new appliance,

please read the following instructions care-

fully as they contain important information

on safety, installation, operation and main-

tenance. Keep the instructions for future

reference.

On receipt, check to ensure that the ap-

pliance has not been damaged during

transport. Transport damage should be

reported to the local distributor before the

wine cooler is put to use.

Remove the packaging. Clean the inside of

the cabinet using warm water with a mild

detergent. Rinse with clean water and dry

thoroughly (see cleaning instructions). Use

a soft cloth.

If during transport the appliance has been

laid down, or if it has been stored in cold

surroundings (colder than +5°C), it must be

allowed to stabilise in an upright position for

at least an hour before being switched on.

4

GB

600

g. 2

g. 3

Placement

For safety and operational reasons, the

appliance must not be installed outdoors.

The appliance should be placed on a level

surface in a dry, well ventilated room (max.

75% relative air humidity). Never place the

appliance close to sources of heat such as

cookers or radiators, and avoid placing it in

direct sunlight.

Room temperature

The climate class is stated on the

nameplate (see g. 1 on page 3 and g. 11

on page 13). This species the optimum

room temperature. Wine coolers with

winter position, however, function at room

temperatures as low as 5ºC.

Climate class Optimum room tem-

perature

SN +10 ºC to +32 ºC

N +16 ºC to +32 ºC

ST +18 ºC to +38 ºC

T +18 ºC to +43 ºC

Installation

The surface on which the appliance is to be

placed must be level. Do not use a frame or

similar.

The appliance can be installed as a free-

standing unit against a wall, built into a

kitchen element, or lined up with other

appliances (gs 2-3).

Installation and start-up

5

GB

1650/1950

100

1560/1860

g. 5

g. 6

600

1075

g. 4

Ventilation

It is important that the appliance be

well ventilated and that air can circulate

unhindered above, below and around it.

The gures below illustrate how the

necessary air circulation around the

appliance can be ensured (gs 5-6).

The appliance viewed from

above

If the appliance is placed beside a wall,

there must be sufcient room for its door

to be opened wide enough to allow the

shelves to be pulled out (g. 4).

The distance pieces on the rear of the ap-

pliance ensure sufcient air circulation. Fit

the two caps supplied with the appliance as

shown in g. 7.

g. 7

6

GB

g. 8

It is important that the appliance be

absolutely level. It can be levelled by

screwing the adjustable feet at the front of

the appliance up or down (gs 8-9).

Use a spirit level to check that the appliance

is absolutely level sideways.

Setting up

7

GB

The door can be changed from right-hinged to left-hinged and vice versa as follows:

Reversible door

1. Lay the appliance on its back and loosen

the upper hinge.

2. Remove the upper hinge.

4. Carefully remove the covers on the

side of the plinth using a at-headed

screwdriver.

5. Pull up the hinge pin...

...and t it on the opposite side.

8. Click the covers into place on the plinth

sides on the opposite side.

6. Unscrew the lock pin using a at-headed

screwdriver.

9. Fit the door onto the bottom pin, t the

top hinge and tighten securely.

3. Rotate the glass door through 180° (on

FZ 295 W, pull the handle to loosen it

on the inside from beneath the sealing

strip).

7. When the lock pin has been loosened

completely, pull it up together with the

lock cylinder and ret on opposite side.

10. After reversing the door, it is important to check that the sealing strip provides a tight seal all the way round. If it does not, carefully heat

the strip all the way round using a hair dryer. Then ease the strip outwards slightly so that it forms a tight seal against the cabinet. Be

careful not to heat the strip so much that it melts!

8

GB

The appliance is intended for connection

to alternating current. The required volt-

age (V) and frequency (Hz) are stated on

the nameplate inside the appliance. Power

must be connected via an independent wall

socket outlet.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or a similar qualied person in

order to avoid a hazard.

Technical data

This appliance complies with CE marking

regulations, directives and standards.

Low Voltage Directive 73/23/EEC.

EMC Directive 89/336/EEC.

Electrical connection

9

GB

Electronic controls

The electronic controls ensure that the set

temperatures are maintained at the top and

bottom of the cabinet. This is accomplished

by complex control of the refrigerating

system the heating element and the fan.

Following any power failure, the

temperature settings are automatically

recalled.

The electronic controls have the following

functions:

• Temperature setting

• Temperature display

• Automatic defrosting

• Fault-nding, emergency and service

programs

• Low-temperature alarm

On/off switch

The light switch is used to select either

continuous illumination or illumination

only when the door is opened.

Temperature display

The display shows the actual temperature

at the top or bottom of the cabinet. To

switch the display between the top and

bottom sections, short-press the top and

bottom buttons respectively, which section

is shown is indicated by a line of light in

the display just beside the buttons . The

temperature display has a built-in lter

that simulates the actual temperature in

the bottles. The displayed temperature

is therefore not affected by transient

uctuations in air temperature.

Temperature setting

The temperature is set using the two

buttons on the control panel. The upper

button is used to set the temperature at

the top of the cabinet. The lower button is

used to set the temperature at the bottom.

Deactivate the childproof lock by pressing

the button for 3 seconds. The display

then starts ashing and shows the current

temperature setting for the zone concerned.

This applies to both buttons/sections. When

the display starts ashing, the temperature

can be set by scrolling the setting between

22 and 5°C. When the desired setting is

displayed, release the button for 3 seconds.

The setting will then be stored and the

childproof lock reactivated.

Note that the bottom section cannot be

given a higher temperature setting than

the top section. The highest available

temperature setting for the bottom section

is therefore identical to the actual setting for

the top section.

On/off switch

Light switch

Operation and function

g. 9

10

GB

Low-temperature alarm

If the temperature has been below 2°C

for more than 1 hour, the display ashes

and Lo/actual temperature are alternately

shown. Wine cannot mature properly at

sub-zero temperatures.

Two-zone setting for serving temperature

Typical serving temperature settings for the

top and bottom sections are 16°C and 6°C

respectively. With these settings, a suitable

temperature gradient will be achieved in

the cabinet for the storage of various types

of wine distributed from top to bottom as

follows:

- heavy red wines +16 to +19°C

- rosé and light red wines +12 to +16°C

- white wines +10 to +12°C

- champagne and sparkling wines +6 to

+8°C

It is recommended that wine be served at a

temperature which is a couple of degrees

lower than the desired drinking temperature

as the wine will be warmed slightly when it

is poured into the glass.

Single-zone setting for long-term storage

For long-term wine storage, the top and bot-

tom sections should both be set at 12°C.

With identical settings for the top and bot-

tom sections, the controls will maintain an

even temperature throughout the cabinet.

However, the temperature in the room will

gradually affect the temperature in the

cabinet through its door and sides, creating

a slight temperature gradient from top to

bottom. The controls will maintain the set

temperature at the bottom of the cabinet,

and any deviation from the setting will

therefore occur at the top.

The difference will vary from 0 to 3°C, de-

pending on the ambient temperature.

11

GB

Automatic defrosting

The wine cooler is defrosted automatically.

Defrost water runs through a pipe and is

collected in a tray above the compressor

where the heat generated by the compres-

sor causes it to evaporate. The defrost

water tray should be cleaned at intervals.

Cleaning

Before cleaning the appliance, unplug it

from the main supply. The cabinet is best

cleaned using warm water (max. 65°C) with

a little mild detergent. Never use cleaning

agents that scour. Use a soft cloth. Rinse

with clean water and dry thoroughly. The

defrost water channel, in which condensa-

tion from the evaporator runs, is located

at the bottom of the rear inside wall of the

cabinet and must be kept clean. Add a few

drops of disinfectant, e.g. Rodalon, to the

defrost water drain a couple of times a year,

and clean the drain using a pipe cleaner or

similar. Never use sharp or pointed imple-

ments. The sealing strip around the door

must be cleaned regularly to prevent discol-

ouration and prolong service life. Use clean

water. After cleaning the sealing strip, check

that it continues to provide a tight seal. Dust

collecting on the condenser on the rear of

the cabinet, the compressor and in the com-

pressor compartment is best removed using

a vacuum cleaner.

Defrosting, cleaning and maintenance

Replacing the light tube

Before replacing the light tube, unplug the

appliance from the main supply. Remove

the lamp cover using a small at-headed

screwdriver. Replace the PLC tube (11 W).

Ret the lamp cover, reconnect the power

supply and start the appliance by pressing

the on/off switch.

g. 10

12

GB

Fault nding

Fault Possible cause Remedy

The appliance is

“dead”!

The appliance is switched off.

Power failure; the fuse is blown;

the appliance is not plugged in

correctly.

Press the on/off switch.

Check that power is connected.

Reset the fuse.

Water collects in

the bottom of the

cabinet.

The defrost water pipe is

blocked.

Clean the defrost water channel

and the drain hole on the rear

wall of the cabinet.

Vibration or

bothersome noise.

The appliance is not level.

The appliance is resting against

other kitchen elements.

Containers or bottles inside the

cabinet are rattling against one

another.

Level the appliance using a spirit

level.

Move the appliance away from

the kitchen elements or appli-

ances it is in contact with.

Move containers and/or bottles

apart.

Compressor runs

continuously.

High room temperature. Ensure adequate ventilation.

E1 is shown on the

display.

The upper sensor is disconnect-

ed or short-circuited.

Call for service. The temperature

within the entire cabinet is main-

tained at the higher of the two

setpoints until the fault has been

corrected.

E2 is shown on the

display.

The lower sensor is disconnected

or short-circuited.

Call for service. The temperature

within the entire cabinet is main-

tained at the higher of the two

setpoints until the fault has been

corrected.

ULO is shown on

the display.

The mains voltage is lower than

184 V.

UHI is shown on the

display.

The mains voltage is higher than

255 V.

13

GB

Warranty disclaimer

Faults and damage caused directly or

indirectly by incorrect operation, misuse,

insufcient maintenance, incorrect building-

in, installation or mains connection, re,

accident, lightening, voltage variation or

other electrical interference, including

defective fuses or faults in mains

installations, or repairs performed by others

than service centres approved by Vestfrost,

and any other faults and damage that the

manufacturer can substantiate are caused

by reasons other than manufacturing or

material faults are not covered by the

warranty.

Transport damage discovered by the buyer

is primarily a matter to be settled between

the buyer and the distributor, i.e. the

distributor must ensure that such complaints

are resolved to the buyer’s satisfaction.

Before calling for technical assistance,

please check whether you are able to rectify

the fault yourself (see Fault nding). If your

request for assistance is unwarranted, e.g.

if the appliance has failed as a result of a

blown fuse or incorrect operation, you will

be charged the costs incurred by your call

for technical assistance.

Spare parts

When ordering spare parts, please state the

type, serial and product numbers of your

appliance (see g. 1 on page 3 and g. 11).

This information is given on the nameplate

inside the cabinet. The nameplate contains

various technical information, including type

and serial numbers.

Note: Always use approved service centres

when your appliance is to be repaired or

replaced!

Service

Vestfrost has local service centres all over

the country who specialise in Vestfrost

products. Here you can obtain xed prices

and professional help for all repairs. Find

your local service centre on www.vestfrost.

dk.

Warranty, spare parts and service

g. 11

14

GB

Environmental regulations on disposal must

also be observed. When disposing of the

appliance you should contact your local

authority technical department who will

inform you of how collection and recycling

of such units take place in your area.

This appliance is marked according to

the European directive 2002/96/EC on

Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of

correctly, you will help prevent potential

negative consequences for the environment

and human health, which could otherwise

be caused by inappropriate waste handling

of this product.

The symbol on the product, or on the

documents accompanying the product,

indicates that this appliance may not be

treated as household waste. Instead it shall

be handed over to the

applicable collection point for the recycling

of electrical and electronic

equipment.

Disposal must be carried out in accordance

with local environmental regulations for

waste disposal.

For more detailed information about

treatment, recovery and recycling of this

product, please contact your local city

ofce, your household waste disposal

service or the shop where you purchased

the product.

Disposal

2

DE

Vielen Dank für Ihre Wahl eines Weinküh-

lschranks von Vestfrost. Beachten Sie

bitte, dass die Bedienungsanleitung für alle

Weinkühlschränke der FZ-Serie gilt. Darum

entsprechen Abbildungen und Ausstattung

nicht in jedem Fall genau Ihrem Gerät.

Warnung

Da ein brennbares Gas (Isobutan R600a)

als Kältemittel dient, ist besondere Vorsi-

cht bei Transport und Installation geboten,

damit kein Teil des Kühlkreislaufs beschä-

digt wird.

Sollte dies dennoch geschehen, vermeiden

Sie Funken und offenes Feuer! Lüften Sie

den Raum gründlich, schalten Sie danach

die Stromzufuhr zum Gerät aus, und wen-

den Sie sich an Ihren Lieferanten.

Wartungs- und Reparaturarbeiten dürfen

nur von einem qualizierten Servicecenter

durchgeführt werden.

Alte Geräte

Alte Kühl- und Gefriergeräte sind häug mit

komplizierten Schnappschlössern verseh-

en, die von innen nicht geöffnet werden

können. Falls bei Ihnen ein solches Gerät

steht, oder wenn Sie ein solches Gerät

ausrangieren, machen Sie bitte zuerst das

Schloss unbrauchbar. So verhindern Sie,

dass spielende Kinder eingesperrt werden

und in Lebensgefahr kommen können.

Vor dem Gebrauch

Vor dem Gebrauch Ihres neuen Geräts

sollten Sie diese Bedienungsanleitung

gründlich lesen. Sie enthält wichtige Infor-

mationen zu Sicherheit, Installation, Betrieb

und Wartung. Bewahren Sie die Bedienung-

sanleitung auf. Sie könnten sie zu einem

späteren Zeitpunkt evtl. benötigen.

Kontrollieren Sie das Gerät sofort bei

Lieferung auf eventuelle Beschädigungen.

Transportschäden sind dem Händler zu

melden, bevor das Gerät in Gebrauch

genommen wird.

Verpackung entfernen. Das Schrankinnere

mit lauwarmem Wasser und etwas mildem

Spülmittel reinigen. Mit klarem Wasser

nachwischen und gründlich trocknen (siehe

“Reinigung”). Verwenden Sie ein weiches

Tuch.

Falls das Gerät liegend transportiert wurde

oder einer Temperatur von weniger als +5

°C ausgesetzt war, muss es vor dem Ein-

schalten mindestens eine Stunde lang bei

höherer Außentemperatur aufrecht stehen.

Inhalt

Lernen Sie Ihren

Kühlschrank kennen.........................3

Inbetriebnahme und Installation.......4

Wendbare Tür...................................7

Elektrischer Anschluss......................8

Bedienung und Funktion...................9

Abtauen, Reinigung und Wartung...11

Fehlersuche....................................12

Reklamation,

Ersatzteile und Service...................13

Entsorgung.....................................14

3

DE

Lernen Sie Ihren Kühlschrank kennen

Abb.1

Beleuchtung

Kohlelter

Holzfach

Dichtleiste

Typenschild

Türgriff

Fußleiste

Bedienungselemente

Schloss

Einstellbare Füße

4

DE

600

Abb. 2

Abb. 3

Aufstellort

Aus Sicherheits- und betriebstechnischen

Gründen darf das Gerät nicht im Freien

aufgestellt werden.

Stellen Sie den Schrank auf einen

ebenen Untergrund in einem trockenen,

gut belüfteten Raum (max. 75 % relative

Luftfeuchtigkeit). Stellen Sie den

Schrank nicht in unmittelbarer Nähe

von Wärmequellen wie Herden oder

Heizkörpern auf, und vermeiden Sie direkte

Sonneneinstrahlung oder Wärme von

anderen Wärmequellen .

Raumtemperatur

Die Klimaklasse nden Sie auf dem

Typenschild (siehe Abb. 1 Seite 3 und

Abb. 11 Seite 13). Sie gibt an, innerhalb

welcher Raumtemperaturbereiche der

Kühlschrank optimal arbeitet. Weinschränke

mit Winterposition fungieren bis zu einer

Raumtemperatur von 5 °C.

Klimaklasse Zulässige Raumtem-

peratur

SN +10 ºC bis +32 ºC

N +16 ºC bis +32 ºC

ST +18 ºC bis +38 ºC

T +18 ºC bis +43 ºC

Installation

Die Unterlage zum Aufstellen des Schranks

muss eben sein. Verwenden Sie keinen

Rahmen o.ä.

Der Schrank kann frei an einer Wand

stehen, in ein Küchenelement eingebaut

werden oder neben anderen Schränken

aufgestellt werden (Abb. 2-3).

Inbetriebnahme und Installation

5

DE

1650/1950

100

1560/1860

Abb. 5

Abb. 6

600

1075

Abb. 4

Belüftung

Der Schrank muss ausreichend belüftet

sein, und die Luftzirkulation über und unter

ihm sowie seitlich vom Schrank darf nicht

behindert sein.

Die folgenden Abbildungen zeigen, wie

die erforderliche Belüftung in der direkten

Umgebung des Schranks sicherzustellen ist

(Abb. 5-6).

Schrank in Draufsicht

Wird der Schrank an einer Wand auf-

gestellt, ist darauf zu achten, soviel Platz

zu lassen, dass die Tür zum Herausziehen

der Kühlschubladen weit genug geöffnet

werden kann (Abb. 4).

Die Abstandsstücke auf der Rückseite des

Schranks sichern die erforderliche Luftzirku-

lation. Die beiden Abdeckungen montieren,

die zusammen mit dem Schrank mitgeliefert

werden (siehe Abb. 7)

Abb. 7

6

DE

Abb. 8

Der Schrank muss waagerecht stehen.

Der Schrank kann durch Drehen der

einstellbaren Füße ausgerichtet werden

(siehe Abb. 8).

Prüfen Sie mit einer Wasserwaage nach, ob

der Schrank waagerecht steht.

Aufstellung

7

DE

Die Tür kann folgendermaßen von rechts angeschlagen auf links angeschlagen und

umgekehrt umgebaut werden:

Wendbare Tür

1. Den Schrank auf den Boden legen, und

das obere Scharnier lösen.

2. Oberes Scharnier abbauen.

4. Die Abdeckungen in den Sock-

elseiten vorsichtig mit einem achen

Schraubendreher demontieren.

5. Den Scharnierstift herausziehen…

… und auf der entgegengesetzten Seite

montieren.

8. Die Abdeckungen in den Sockelseiten

auf der entgegengesetzten Seite

einrasten.

6. Den Schlossriegel mit einem achen

Schraubendreher losschrauben.

9. Die Tür auf den Scharnierstift montieren,

und das obere Scharnier montieren und

festschrauben.

3. Die Glastüre umdrehen (beim FZ 295

W den Handgriff abnehmen, der innen

unter der Dichtleiste zu lösen ist).

7. Nach Lösen des Schlossriegels diesen

gemeinsam mit dem Schlosszylinder

herausziehen und auf der entgegeng-

esetzten Seite wieder montieren.

10. Nach dem Wechsel der Türanschlagseite ist zu prüfen, ob die Dichtleiste rundum dicht schließt. Tut sie das nicht, können Sie die Leiste

vorsichtig mit einem Haarfön auf ihrer ganzen Länge erwärmen. Ziehen Sie die Leiste dann leicht aus der Tür heraus, sodass sie nach

dem Schließen der Tür wieder dicht am Schrank anliegt. VORSICHT! Die Dichtleiste darf nicht zu stark erwärmt werden, da sie sonst

schmelzen kann!

Stránka se načítá ...

Vestfrost FZ Series Instructions For Use & Warranty

Vestfrost FZ Series Instructions For Use & Warranty

v jiných jazycích

Související papíry

Jiné dokumenty