Yamaha A3000 Návod k obsluze

Owner's Manual

92-469- ➀

Model _____________________________________

Serial No. __________________________________

Purchase Date ______________________________

ENVIRONMENTAL ISSUES: Yamaha strives to pro-

duce products that are both user safe and environmentally

friendly. We sincerely believe that our products and the

production methods used to produce them, meet these

goals. In keeping with both the letter and the spirit of the

law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargable battery which (if applicable) is soldered in

place. The average life span of this type of battery is ap-

proximately five years. When replacement becomes nec-

essary, contact a qualified service representative to per-

form the replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away

from children. Dispose of used batteries promptly and as

regulated by applicable laws. Note: In some areas, the

servicer is required by law to return the defective parts.

However, you do have the option of having the servicer

dispose of these parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and

federal regulations that relate to the disposal of products

that contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the

manufacturer’s warranty, and are therefore the owners

responsibility. Please study this manual carefully and con-

sult your dealer before requesting service.

NAME PLATE LOCATION: The graphic below indi-

cates the location of the name plate. The model number,

serial number, power requirements, etc., are located on

this plate. You should record the model number, serial

number, and the date of purchase in the spaces provided

below and retain this manual as a permanent record of

your purchase.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these

graphics on the enclosure. The explanation of these graph-

ics appears on this page. Please observe all cautions indi-

cated on this page and those indicated in the safety in-

struction section.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important oper-

ating and maintenance (servicing) in-

structions in the literature accompany-

ing the product.

The lightning flash with arrowhead

symbol, within the equilateral triangle,

is intended to alert the user to the pres-

ence of uninsulated “dangerous volt-

age” within the product’s enclosure that

may be of sufficient magnitude to con-

stitute a risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic prod-

ucts are tested and approved by an independent safety

testing laboratory in order that you may be sure that when

it is properly installed and used in its normal and custom-

ary manner, all foreseeable risks have been eliminated.

DO NOT modify this unit or commission others to do so

unless specifically authorized by Yamaha. Product per-

formance and/or safety standards may be diminished.

Claims filed under the expressed warranty may be denied

if the unit is/has been modified. Implied warranties may

also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The

information contained in this manual is believed to be

correct at the time of printing. However, Yamaha reserves

the right to change or modify any of the specifications

without notice or obligation to update existing units.

SPECIAL MESSAGE SECTION

Rear Panel

• Before moving the instrument, remove all connected cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do not

place vinyl or plastic objects on the instrument, since this might discolor the panel.

• Do not rest your weight on, or place heavy objects on the instrument, and do

not use excessive force on the buttons, switches or connectors.

• Do not place objects in front of the instrument's air vent, since this may

prevent adequate ventilation of the internal components, and possibly result

in the instrument overheating. To ensure adequate ventilation and cooling,

leave at least 10cm of open space behind the A3000 rear panel, and at least

4cm of open space above the top cover.

• Do not operate the instrument for a long period of time at a high or uncom-

fortable volume level, since this can cause permanent hearing loss. If you

experience any hearing loss or ringing in the ears, consult a physician.

■SAVING USER DATA

• To protect against data loss caused by malfunction or operating error, be sure

to save your data regularly to floppy disk, hard disk or other storage medium.

Yamaha cannot be held responsible for damage caused by improper use or modi-

fications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

• This instrument contains no user-serviceable parts. Do not attempt to disas-

semble or modify the internal components in any way.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the instrument, or if any unusual smells or

smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the electric plug from the outlet, and have the instrument

inspected by qualified Yamaha service personnel.

• Only use the voltage specified as correct for the instrument. The required

voltage is printed on the name plate of the instrument.

• Always connect the three-pin attachment plug to a properly grounded power

source. (For more information about the main power supply, see “Connect-

ing the Power.)

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the power cord near heat sources such as heaters or radiators,

and do not excessively bend or otherwise damage the cord, place heavy

objects on it, or place it in a position where anyone could walk on, trip over,

or roll anything over it.

• When removing the electric plug from an outlet, always hold the plug itself

and not the cord. Pulling by the cord can damage it.

• Do not connect the instrument to an electrical outlet using a multiple-con-

nector. Doing so can result in lower sound quality, or possibly cause over-

heating in the outlet.

• Remove the electric plug from the outlet when the instrument is not to be

used for extended periods of time, or during electrical storms.

• Before connecting the instrument to other electronic components, turn off

the power for all components. Before turning the power on or off for all

components, set all volume levels to minimum.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent

the possibility of panel disfiguration or damage to the internal components.

• Do not use the instrument near other electrical products such as televisions,

radios, or speakers, since this might cause interference which can affect

proper operation of the other products.

• Do not place the instrument in an unstable position where it might acciden-

tally fall over.

■Handling and Installation of Options

CAUTION

• Before handling an option board, hard disk, or SIMM, you should briefly touch

the A3000 metal casing (or other such metallic area) with your bare hand so as

to drain off any static charge from your body. Note that even a slight amount of

electrostatic discharge may cause damage to these components.

• It is recommended that you wear gloves to protect your hands from metallic

projections on the A3000, hard disk, SIMMs, option boards, and other com-

ponents. Touching leads or connectors with bare hands may cause finger

cuts, and may also result in poor electrical contact or electrostatic damage.

• Take care to avoid dropping screws into the A3000 unit. If a screw does

fall in, be sure to remove it before you reassemble and power up the unit.

Starting the unit with a loose screw inside may lead to improper opera-

tion or equipment failure. (If you are unable to retrieve a dropped screw,

consult your Yamaha dealer for advice.)

WARNING

• Before beginning installation, switch off the power to the A3000 and

connected peripherals, and unplug them from the power outlet. Then

remove all cables connecting the A3000 to other devices. (Leaving the

power cord connected while working can result in electric shock. Leav-

ing other cables connected can interfere with work.)

• Do not disassemble, modify, or apply excessive force to board areas and

connectors on option boards, hard disk, and SIMMs. Bending or tam-

pering with boards and connectors may lead to electric shock, fire, or

equipment failures.

* Consult your Yamaha dealer if you have any questions regarding installation procedures for options boards, hard disks, SIMMs, or other optional devices.

* If SIMM memory, hard disk, or other optional component fails to work properly, consult the item's dealer for advice.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Features

2

Features

Versatile Professional Sampler

The A3000 professional sampler is an ideal break-beat

machine and phrase sampler for a wide variety of re-

cording and performance applications.

Excellent Effects System

The A3000’s triple-block effect system lets you set up

as many as three independent effects. Select from a wide

range of built-in effects — including original effects

custom-designed to heighten the performance quali-

ties of phrase and break-beat play. You can also apply

effects to incoming signals as you record them, and to

analog input that you feed through the A3000 for

realtime output.

Easy to Use

The A3000 presents its editing and control capabilities

in an easy-to-use three-level arrangement. All opera-

tions are handled using front-panel mode buttons, func-

tion keys, and knobs. You can access and edit any set-

ting by selecting the mode, then selecting the func-

tion, and then turning the knobs directly under the

screen. It is also possible to use knobs and function

keys to control realtime playback.

Performance-Enhancing Options

Installation of the optional I/O expansion board (AIEB1

board) adds digital I/O capability plus six additional as-

signable-output pairs to your A3000. The A3000 also

accepts up to 128MB of expansion memory.

List of Accessories

Your A3000 package includes the following accessories. Make sure that all of these accessories are included.

• CD-ROM

• Power cord

• MIDI cable

• Five floppy disks

• Owner’s Manual

• Power supply cable for hard disk (red/white 4-wire cable)

• SCSI cable for hard disk

* If any of the above items is missing, please contact your Yamaha dealer for assistance.

Unauthorized copying of copyrighted software for purposes other than purchaser’s personal use is prohibited.

Features

3

PROFESSIONAL SAMPLER

Owner’s Manual

Thank you for your purchase of the Yamaha A3000 Professional Sampler. The A3000

incorporates a leading-edge AWM2 tone generator, and is an ideal for use with synthesiz-

ers, MIDI keyboards, and other MIDI devices in a wide variety of musical applications.

This owner’s manual will help you get the most from your A3000’s many advanced fea-

tures. Please read through the essential parts of the manual carefully before beginning

work with your sampler, and refer back to the manual for additional information as

necessary. Please be sure to store the manual in a safe and handy location.

Contents

4

Using the Manual .............................................................................. 6

Panel and Connector Arrangement .................................................. 8

A3000 Options ................................................................................. 14

Handling the Floppy Disk Drive(FDD) and Floppy Disk ............... 16

Chapter 1 Setting Up

Setting Up........................................................................................ 20

Connecting the Power .................................................................... 21

Connecting the A3000 Outputs ...................................................... 22

Connecting the Audio Inputs ......................................................... 25

MIDI Connections ........................................................................... 27

Power ON/OFF ................................................................................ 30

Sound Check ................................................................................... 32

Chapter 2 Trying It Out

Introduction .................................................................................... 36

Starting Out .................................................................................... 38

Next Step ......................................................................................... 45

Sample Editing................................................................................ 52

Program Editing ............................................................................. 57

Sequence Play ................................................................................. 62

Saving and Reloading Your Data .................................................... 64

Accompanying Disks ....................................................................... 68

Chapter 3 Basics

Samples and Programs ................................................................... 70

Sample Output Destinations and Effects ....................................... 78

Data Configuration and Handling .................................................. 80

Modes and Functions ...................................................................... 84

Basic Operation ............................................................................... 86

Other Keys and Operations ............................................................. 91

Chapter 4 PLAY Mode

Play Mode ........................................................................................ 94

Program & Sample Selection Screen ............................................. 95

PROGRAM/SAMPLE Selection Screen ................................................... 95

COMMAND Pages ............................................................................ 98

SAVE ........................................................................................................ 98

INIT (Program Initialization) ............................................................... 101

COPY ..................................................................................................... 102

PGMDUMP (Program Dump) .............................................................. 103

SETINIT (Set Program’s Initial Conditions)........................................ 104

NEWBANK (Create a Sample Bank) ..................................................... 105

DELETE ................................................................................................ 106

DUPL (Duplicate) .................................................................................. 107

SMPDUMP (Sample Dump) .................................................................. 108

PROGRAM Function ..................................................................... 110

PROGRAM - PgmSel (Select Program) ................................................ 110

SAMPLE Function ........................................................................ 112

SAMPLE - SmpSel (Select Sample)...................................................... 112

SAMPLE - SmpBnk (Select Sample from Sample Bank) .................... 114

SAMPLE - ToBank (Assign Sample to Bank) ....................................... 115

SAMPLE - SmpSort (Sort Samples) ..................................................... 117

EASY EDIT Function .................................................................... 118

EASY EDIT - EasyEd ............................................................................. 119

EFFECT Function ......................................................................... 121

EFFECT - EfType (Select the Effect Types) .......................................... 121

EFFECT - Efct1,...,Efct3 (Edit the Effects) .......................................... 124

EFFECT - In&Out (Input/output levels and pan) ................................ 126

EFFECT - EdType (Effect Edit Type) .................................................... 127

SETUP Function ........................................................................... 128

SETUP - PgmMstr (Program’s Master Settings) .................................. 128

SETUP - Portmnt (Portamento) ........................................................... 130

SETUP - ADSetup (A/D-In Setup) ........................................................ 132

SETUP - ADOut (Output Setup for A/D-Input Signal) ........................ 134

CONTROL Function...................................................................... 136

CONTROL - PgmCtl1 (Program Controller Setup 1) .......................... 136

CONTROL - PgmCtl2 (Program Controller Setup 2) .......................... 139

CONTROL - Reset (Controller Reset) ................................................... 141

Chapter 5 EDIT Mode

EDIT Mode .................................................................................... 144

COMMAND Pages .......................................................................... 147

SAVE ...................................................................................................... 147

REVERT ................................................................................................. 149

NORM (Normalize) ............................................................................... 150

RESMPL - TmStrch (Resampling - Time Stretch) .............................. 151

RESMPL - PtchCnv (Resampling - Pitch Conversion) ........................ 153

FADE ..................................................................................................... 155

REVERS (Reverse) ................................................................................ 157

LOOPXFD (Loop Crossfade) ................................................................. 158

SETINIT (Register Initial Parameter Values)....................................... 160

TRIM/LOOP Function ................................................................... 161

TRIM/LOOP - Config (Configure)......................................................... 161

TRIM/LOOP - Wave (Edit Waveform) ................................................... 164

TRIM/LOOP - Loop (Edit Loop Addresses) ........................................... 166

TRIM/LOOP - WvMode (Set Wave Mode) ............................................. 168

MAP/OUT Function ....................................................................... 170

MAP/OUT - KeyRnge (Key Range) ........................................................ 170

MAP/OUT - VelRnge (Velocity Range) .................................................. 172

MAP/OUT - Lvl&Mode ........................................................................... 174

MAP/OUT - Output ................................................................................ 176

MAP/OUT - Pitch ................................................................................... 178

MAP/OUT - Expand ............................................................................... 179

MAP/OUT - LvlScale (Level Scaling) .................................................... 180

FILTER Function .......................................................................... 182

FILTER - Filter ...................................................................................... 182

FILTER - FltSens (Filter Sensitivity) ................................................... 184

FILTER - FltScale (Filter Scaling) ........................................................ 185

FILTER - EQ (Equalization) ................................................................. 187

EG Function .................................................................................. 188

EG - AEG (Amplitude Envelope Generator)......................................... 188

EG - AEGMode (AEG Mode Settings) ................................................... 190

EG - FEGRate (Filter-EG Rates) ........................................................... 192

EG - FEGLevel (Filter-EG Levels) ........................................................ 194

EG - FEGMode (FEG Mode Settings) ................................................... 196

EG - PEGRate (Pitch-EG Rates) ........................................................... 198

EG - PEGLevel (Pitch-EG Levels) ........................................................ 200

Contents

5

EG - PEGMode (PEG Mode Settings) ................................................... 201

LFO Function ................................................................................ 203

LFO - Common ..................................................................................... 203

LFO - FltrMod (Filter Modulation) ...................................................... 205

LFO - PtchMod (Pitch Modulation)...................................................... 206

LFO - AmpMod (Amplitude Modulation) ............................................. 207

MIDI/CTRL Function .................................................................... 208

MIDI/CTRL - RCh&Alt (Receive Channel and Alternate ..................... 208

MIDI/CTRL - SmpCtl1 (Sample Controller Setup 1) ........................... 210

MIDI/CTRL - SmpCtl2 (Sample Controller Setup 2) ........................... 213

MIDI/CTRL - Vel&PB (Velocity and Pitchbend) ................................... 215

Chapter 6 RECORDING Mode

RECORDING Mode ....................................................................... 220

COMMAND Page ........................................................................... 221

SAVE ...................................................................................................... 221

RECORD Function ........................................................................ 223

RECORD - Record ................................................................................. 223

SETUP Function ........................................................................... 227

SETUP - RecData .................................................................................. 227

SETUP - Target...................................................................................... 230

SETUP - KeyRnge ................................................................................. 232

SETUP - Trigger .................................................................................... 234

SETUP - Process.................................................................................... 235

METER Function .......................................................................... 236

METER - Meter ..................................................................................... 236

METER - TrgLvl .................................................................................... 237

EFFECT Function ......................................................................... 238

EFFECT - EfType (Select the Effect Types) ........................................ 238

EFFECT - RecEf1,...,RecEf3 (Edit the Effects) .................................... 239

EFFECT - In&Out (Input/output levels and pan)................................ 240

EFFECT - EdType (Effect Edit Type) .................................................... 240

EXT CTRL Function ..................................................................... 241

EXT CTRL - CD-ROM ........................................................................... 241

EXT CTRL - CD-DA ............................................................................... 242

MONITOR Function ...................................................................... 243

MONITOR - Monitor ............................................................................. 243

MONITOR - Click .................................................................................. 245

Chapter 7 DISK Mode

DISK Mode .................................................................................... 248

COMMAND Pages .......................................................................... 249

LOAD ..................................................................................................... 249

DELETE ................................................................................................ 250

COPY ..................................................................................................... 251

FORMAT ................................................................................................ 252

PHYS_FMT (Physical Format) ............................................................. 254

PART_FMT (Format a Partition) .......................................................... 256

FD_FMT (Format a Floppy Disk) ......................................................... 258

PROGRAM Function ..................................................................... 259

PROGRAM - PgmLoad (Load Program(s)) ........................................... 259

SAMPLE Function ........................................................................ 261

SAMPLE - SmpLoad (Load Sample(s)) ................................................ 261

SEQUENCE Function ................................................................... 264

SEQUENCE - SeqLoad (Load Sequence(s)) ......................................... 264

VOLUME Function ........................................................................ 266

VOLUME - Volume ................................................................................ 266

DISK Function .............................................................................. 268

DISK - Disk ........................................................................................... 268

DISK - Config (Configure) .................................................................... 270

DISK - SelfID ........................................................................................ 271

IMPORT Function ......................................................................... 272

IMPORT - ImpSmp (Import a sample)................................................. 272

IMPORT - ImpVce (Import a voice) ...................................................... 274

IMPORT - ImpOthr (Import Other Data Type) .................................... 276

Chapter 8 UTILITY Mode

UTILITY Mode ............................................................................... 280

COMMAND Pages .......................................................................... 281

SAVE ...................................................................................................... 281

DELETE ................................................................................................ 283

SAVESYS (Save System Settings)......................................................... 284

LOADSYS (Load System Settings) ....................................................... 285

ALLDUMP (Data Dump) ....................................................................... 286

TOTAL EQ Function ..................................................................... 287

Total EQ - Gain...................................................................................... 288

Total EQ - Freq ...................................................................................... 289

Total EQ - Width ................................................................................... 290

PANEL PLAY Function.................................................................. 291

PANEL PLAY - KnobCtl (Knob Control) .............................................. 291

PANEL PLAY - KnobSet ........................................................................ 292

PANEL PLAY - FKeySet (Set Function Keys) ....................................... 294

SEQUENCE Function ................................................................... 296

SEQUENCE - SeqSel (Select Sequence) .............................................. 296

SEQUENCE - Play&Rec (Playback and Recording) ............................. 297

MASTER Function ........................................................................ 298

MASTER - Tuning ................................................................................. 298

MASTER - StOut (Stereo Output Assignment) .................................... 299

SYSTEM Function ........................................................................ 300

SYSTEM - Keys ..................................................................................... 300

SYSTEM - Display ................................................................................. 302

SYSTEM - Page ..................................................................................... 303

SYSTEM - FreeMem .............................................................................. 304

MIDI Function .............................................................................. 305

MIDI - Receive ....................................................................................... 305

MIDI - Adjust ......................................................................................... 307

MIDI - RcvFlt (Receiving Filter) ........................................................... 309

MIDI - Bulk (Bulk Dump) ..................................................................... 310

Appendix

Installing SIMMs ........................................................................... 312

Installing the AIEB1 I/O Expansion Board .................................. 316

Setting the SCSI Board Terminator Switch ................................. 320

Installing an Internal Hard Disk .................................................. 323

Connecting external SCSI devices................................................ 328

Specifications ................................................................................ 332

Effect type list ............................................................................... 335

Effect parameter list ..................................................................... 337

Control change number list ......................................................... 347

Troubleshooting ............................................................................ 348

Error messages.............................................................................. 351

MIDI data format........................................................................... 352

Index

Index .............................................................................................. 364

Using the Manual

6

Using the Manual

Manual Organization

This manual comprises eight chapters and an Appendix. Chapters 1 and 3 contain es-

sential information and should be read carefully. You may also wish to run through the

brief tutorial given in Chapter 2 before beginning serious work with the A3000.

Chapters 4 through 8 provide detailed information about each of the five operating

modes. Refer to this information as needed while working with the A3000.

■ Chapter 1 Setting Up

This chapter explains the A3000’s controls and connectors, and shows how to connect

up speakers and MIDI devices. Please read through this chapter before you start to work

with the A3000.

■ Chapter 2 Trying It Out

This chapter guides you through a trial run with the A3000. Going through these proce-

dures will help you get a good feel for basic A3000 operations.

■ Chapter 3 Basics

The chapter introduces basic concepts, terminology, and operating procedures. Read

this chapter to learn about samples, sample banks, programs, and sequences; modes

and functions; screen displays; and other important features.

■ Chapter 4 PLAY Mode

This chapter explains all PLAY-mode functions. You use PLAY mode to edit and play

programs.

■ Chapter 5 EDIT Mode

This chapter explains all EDIT-mode functions. You use EDIT mode to edit your samples

and sample banks.

■ Chapter 6 RECORDING Mode

This chapter explains all RECORDING-mode functions. You use RECORDING mode to

record samples and sequences.

■ Chapter 7 DISK Mode

This chapter explains all DISK-mode functions. You use DISK mode to manage your

floppy and hard disks.

■ Chapter 8 UTILITY Mode

This chapter explains all UTILITY-mode functions. You use UTILITY mode to set the

system’s environment.

■ Appendix

Provides option installation instructions, troubleshooting advice, error-message descrip-

tions, A3000 specifications, and MIDI information.

Using the Manual

7

Finding the Information You Need

You can use any of the following methods to locate information within this manual.

Use the

Contents

.

Check the Contents on pages 4 to 6.

Use the Index.

Refer to the Index on pages 363 to 367.

Refer to

Panel and Connector Arrangement

.

Go to the “Panel and Connector Arrangement” section (pages 8 to 14) and locate the

knob, key, or other component that you require information about. Then refer to the

indicated page.

Leaf through the manual.

Page through sections related to the feature you need information about. Note that

each page has a header indicating the page’s contents, and a footer indicating the chap-

ter name.

Icons

This manual uses the following icons to call attention to specific types of information.

Important: An important note or precaution intended to help you avoid

loss of data or other major inconvenience. Always read these notices care-

fully.

FYI (For Your Information): Reference information indirectly related to

the content of the main text. May contain practical advice or general sup-

plementary information.

Procedure: Step-by-step instructions for carrying out a particular opera-

tion. A ▼ mark within a procedure indicates the result produced by carry-

ing out the immediately preceding instruction.

☞ xx Page reference. Directs you to another page for related information.

Screen illustrations and other drawings within this manual are for explanatory pur-

poses only, and may in some cases differ from actual displays and configurations.

Panel and Connector Arrangement

8

MASTER VOL REC VOL

PHONES L INPUT R

1 2 3 4 5

(5)(2)

(1)

(3)

(4)

(7)(6)

Panel and Connector Arrangement

Front Panel (Left Side)

(1) MASTER VOL (Master Volume)

Adjusts the output level at the STEREO OUT connectors only. This knob does not affect

the output level at the ASSIGNABLE OUT connectors, or at the various connectors

provided on the optional I/O expansion board (AIEB1 board).

Panel and Connector Arrangement

9

(2) REC VOL (Recording Volume)

Adjusts the input level from the front panel’s INPUT L and INPUT R jacks. Use the knob

to adjust the level when recording a sample, or when passing an input signal directly

through the A3000 outputs for realtime output (“A/D In” feature).

This knob does not affect the input level to the DIGITAL IN and OPTICAL IN connectors

on the optional I/O expansion board (AIEB1 board).

(3) PHONES jack

Connects to a set of stereo headphones. The PHONES jack always produces the same

signal as the STEREO OUT jacks. Note that headphone impedance should be between

16 and 150 ohms.

(4) INPUT L, INPUT R jacks

Use these jacks to input an analog signal for recording, or for realtime output (“A/D In”

feature). Use the INPUT L jack if you are supplying a monaural signal.

(5) Display

The display indicates the status and settings for the currently selected function, and

presents messages and confirmation prompts. When you are working at a parameter-

setting page, the top line of the display indicates the parameter names, while the bot-

tom line shows the current values. The names and values appear directly over the knobs

that you use to make the settings.

(6) Knob “push” lamps

The lamp above the knob lights up to indicate that the knob can be pushed to execute

some action. If the lamp is off, pushing the knob has no effect.

(7) Knobs

You use the knobs to set the various parameter values, to switch display pages, and

execute operations. In most cases you turn the knob to set a value, and push the knob to

execute an operation — for example, to start or stop recording. Knobs are numbered 1

to 5.

Panel and Connector Arrangement

10

Front Panel (Right Side)

(1) Mode buttons

The A3000 provides five operating modes. You select the mode by pressing the corre-

sponding mode button. The button lamp comes on to indicate that the mode is selected.

Each mode is further divided into six functions. After selecting the mode, you can switch

among its functions by pressing the appropriate function keys.

(The A3000 also uses the button lamps to let you know that it is receiving MIDI data.

Each lamp corresponds to a different MIDI data type, and will continue to blink while

the A3000 is receiving MIDI data of that type. (☞92))

(2) Function keys

Use these keys to switch among the six functions within the currently selected mode.

(3) COMMAND key

You press the COMMAND key to access additional commands relevant to the mode and

function that you are currently working in. (☞91)

PLAPLAYY

EDITEDIT

RECREC

DISKDISK

UTILITYUTILITY

PROGRAMPROGRAM

TRIM/LOOPTRIM/LOOP

RECORDRECORD

PROGRAMPROGRAM

TTOTOTALAL EQ EQ

SAMPLESAMPLE

MAP/OUTMAP/OUT

SETUPSETUP

SAMPLESAMPLE

PPANELANEL PLA PLAYY

EASYEASY EDIT EDIT

FILFILTERTER

METERMETER

SEQUENCESEQUENCE

EFFECTEFFECT

EGEG

EFFECTEFFECT

VOLUMEVOLUME

MASTERMASTER

SETUPSETUP

LFOLFO

EXITEXIT CTRL CTRL

DISKDISK

SYSTEMSYSTEM

CONTROLCONTROL

MIDI/CTRLMIDI/CTRL

MONITMONITOROR

IMPORIMPORTT

MIDIMIDI

COMMAND ASSIGNABLE AUDITION

POWERPOWER

ON/ON/ OFFOFF

(1)

(2)

(7)

(6)(5)(4)(3)

Panel and Connector Arrangement

11

(4) ASSIGNABLE key

You can assign this key any of four different functions. You can set it to operate as a

damp key (so that it switches all sound off), as a controller reset button, or as a toggle

for the knob-controller feature (knobs act as controllers) or the function-key playback

feature (function keys act as MIDI keys). (☞91)

(5) AUDITION key

Press the key to play out the currently selected sample. You use this feature to check the

sound of the sample while editing.

(6) Floppy-disk drive

Accepts a 3.5-inch floppy disk. You can use floppy disks to save and reload your data

(programs, samples, sequences, and system settings).

Note that there is an access lamp at the lower left of the drive. The lamp lights up while

the disk is being accessed. Please do not eject the floppy-disk while this lamp is on.

To eject a disk, press the EJECT button at the lower right of the drive.

(7) POWER switch

Press once to switch the power on. Press again to turn the power off.

Important

The A3000 stores all new data into main memory only, and will lose all of this data when

you switch off the power. You must therefore be sure to save all important data to disk

before turning the A3000 off.

Panel and Connector Arrangement

12

Rear Panel

(1) AC inlet

Connects to the AC power cord supplied with the A3000. (Please do not use any other

power cord with this unit.)

(2) MIDI connectors

These connectors link the A3000 to external MIDI devices. The MIDI IN connector re-

ceives MIDI signals, while the MIDI OUT connector transmits MIDI data generated by

the A3000. The MIDI THRU connector relays the MIDI signals received at the MIDI IN

connector.

(3) ASSIGNABLE OUT jacks

Analog output jacks. These jacks operate independently of the STEREO OUT jacks. You

can use these jacks to output the sound of one or more selected samples, or to output

the signal supplied through the front panel’s analog input connectors (☞134, 176). You

may also set them so that they output the same signal as the STEREO OUT jacks (☞299).

(4) STEREO OUT jacks

These are the main analog output jacks.

(5) SCSI connector

This is a half-pitch 50-pin connector. You use it to connect up a SCSI hard drive, CD-

ROM drive, or other SCSI device.

(1) (2)

(3) (4)

(5)

Panel and Connector Arrangement

13

Rear Panel (with optional AIEB1 board installed)

(1) (2) (3)

(1) OPTICAL IN, OUT connectors

Use these connectors to input or output digital signals over optical-fiber cable. You can

use the OPTICAL IN to record a digital signal of frequency 48kHz, 44.1kHz, or 32kHz.

The OPTICAL OUT connector outputs a digital signal of frequency 44.1kHz.

(2) DIGITAL IN, OUT connectors

Use these connectors to input or output digital signals over coaxial (RCA-pin) cable. The

digital signal format is CD/DAT (S/P DIF).

You can use the DIGITAL IN connector to record a digital signal of frequency 48kHz,

44.1kHz, or 32kHz. The DIGITAL OUT connector outputs a digital signal of frequency

44.1kHz.

(3) ASSIGNABLE OUT jacks (AS1 to AS6)

Additional analog output jacks. Each pair (1&2, 3&4, 5&6) operates independently of all

other outputs on the A3000. You can use these jacks to output the sound of one or more

selected samples, or to output the signal supplied through the front panel’s analog in-

put connectors (☞134, 176). You may also set them so that they output the same signal

as the STEREO OUT jacks (☞299).

A3000 Options

14

A3000 Options

You can enhance the capability of your A3000 by installing options. The A3000 supports

two options: (1) additional memory, and (2) the AIEB1 board (I/O expansion board).

Expansion Memory (SIMMs)

The A3000 stores all active data in main memory. To play a sample back, you must first

load it into main memory. And whenever you record a sample, you must record it into

main memory.

Samples consume a great deal of memory. The A3000 comes standard with 2 megabytes

(2MB) of memory — but this is only sufficient to store about 23 seconds of high-quality

monaural sound (at 44.1kHz sampling frequency), or approximately 11.5 seconds of

stereo sound.

You can increase this capacity by installing additional memory. The A3000 accepts ex-

pansion memory in the form of SIMMs (single in-line memory modules). Using SIMMs,

you can install up to 128MB of memory onto the A3000. SIMMs can be purchased from

almost any computer-supply dealer.

Adding memory will allow you to record longer samples, and to work with more sam-

ples at the same time. For information about how to install SIMMs, refer to the Appen-

dix. (☞312)

Important

• You need to use 72-pin SIMMs with access time of 70ns or less. The SIMM module

size may be 4MB, 8MB, 16MB, or 32MB. The A3000 is designed for use with 32-bit

SIMMs, but can also accept installation of 36-bit (parity-type) SIMMs.

• SIMMs must be installed in pairs: you can install either two SIMMs or four SIMMs.

Both modules in a pair must have the same memory capacity.

• The A3000 ships with 2MB of sampling memory installed, and is capable of accessing

up to 128MB. If you add one pair of 32MB SIMMs, for example, you increase the

available sampling memory to a total of (2 + 32×2 =) 66MB. If you install four 32MB

SIMMs, however, the sampling memory size becomes 128MB (and the original 2MB

are effectively disabled).

• For more information about SIMM purchase, refer to your A3000 dealer.

A3000 Options

15

The I/O Expansion Board (AIEB1 Board)

In its standard configuration, the A3000 supports analog I/O only. Although it stores all

internal data in digital form, it does not provide direct digital I/O connectors.

You can add digital I/O capacity by installing an AIEB1 board. The board offers two

different digital connector types: optical connectors, and coaxial connectors. As an added

benefit, the board also includes three stereo ASSIGNABLE OUTPUT pairs (six analog

jacks), which operate independently of the standard STEREO OUT and ASSIGNABLE

OUT jacks.

For information about how to install this board, refer to the Appendix. (☞312)

Handling the Floppy Disk Drive(FDD) and Floppy Disk

16

Handling the Floppy Disk Drive(FDD) and Floppy Disk

Precautions

Be sure to handle floppy disks and treat the disk drive with care. Follow the important

precautions below.

Disk Type

The A3000 disk drive accepts 2HD-type and 2DD-type 3.5" floppy disks.

Inserting/Ejecting Floppy Disks

To insert a floppy disk into the disk drive:

Hold the disk so that the label of the disk is facing upward and the sliding shutter is

facing forward, towards the disk slot. Carefully insert the disk into the slot, slowly push-

ing it all the way in until it clicks into place and the eject button pops out.

To eject a floppy disk:

Before ejecting the disk, be sure to confirm that the FDD is stopped (check if the LED

below the floppy disk slot is off).

Press the eject button slowly as far as it will go; the disk will automatically pop out.

When the disk is fully ejected, carefully remove it by hand.

Never attempt to remove the disk or turn the power off during reading or writing. Do-

ing so can damage the disk and possibly the disk drive.

If the eject button is pressed too quickly, or if it is not pressed in as far as it will go, the

disk may not eject properly. The eject button may become stuck in a half-pressed posi-

tion with the disk extending from the drive slot by only a few millimeters. If this hap-

pens, do not attempt to pull out the partially ejected disk, since using force in this

situation can damage the disk drive mechanism or the floppy disk. To remove a partially

ejected disk, try pressing the eject button once again, or push the disk back into the slot

and then repeat the eject procedure.

Be sure to remove the floppy disk from the disk drive before turning off the power. A

floppy disk left in the drive for extended periods can easily pick up dust and dirt that can

cause data read and write errors.

Handling the Floppy Disk Drive(FDD) and Floppy Disk

17

Cleaning the Disk Drive Read/Write Head

• Clean the read/write head regularly. This instrument employs a precision magnetic

read/write head which, after an extended period of use, will pick up a layer of mag-

netic particles from the disks used that will eventually cause read and write errors.

• To maintain the disk drive in optimum working order Yamaha recommends that you

use a commercially-available dry-type head cleaning disk to clean the head about

once a month. Ask your Yamaha dealer about the availability of proper head-cleaning

disks.

Never insert anything but floppy disks into the disk drive. Other objects may cause

damage to the disk drive or floppy disks.

About the Floppy Disks

To handle floppy disks with care:

Do not place heavy objects on a disk or bend or apply pressure to the disk in any way.

Always keep floppy disks in their protective cases when they are not in use.

Do not expose the disk to direct sunlight, extremely high or low temperatures, or exces-

sive humidity, dust or liquids.

Do not open the sliding shutter and touch the exposed surface of the floppy disk inside.

Do not expose the disk to magnetic fields, such as those produced by televisions, speak-

ers, motors, etc., since magnetic fields can partially or completely erase data on the

disk, rendering it unreadable.

Never use a floppy disk with a deformed shutter or housing.

Do not attach anything other than the provided labels to a floppy disk. Also make sure

that labels are attached in the proper location.

To protect your data (Write-protect Tab):

To prevent accidental erasure of important data, slide the disk’s write-protect tab to the

“protect” position (tab open).

Data backup

For maximum data security Yamaha recommends that you keep two copies of impor-

tant data on separate floppy disks. This gives you a backup if one disk is lost or damaged.

18

Stránka se načítá ...

Yamaha A3000 Návod k obsluze

Yamaha A3000 Návod k obsluze

v jiných jazycích

Související papíry

Jiné dokumenty