Yamaha A3000 Návod k obsluze

Kategorie
Hudební vybavení
Typ
Návod k obsluze
Owner's Manual
92-469-
Model _____________________________________
Serial No. __________________________________
Purchase Date ______________________________
ENVIRONMENTAL ISSUES: Yamaha strives to pro-
duce products that are both user safe and environmentally
friendly. We sincerely believe that our products and the
production methods used to produce them, meet these
goals. In keeping with both the letter and the spirit of the
law, we want you to be aware of the following:
Battery Notice: This product MAY contain a small non-
rechargable battery which (if applicable) is soldered in
place. The average life span of this type of battery is ap-
proximately five years. When replacement becomes nec-
essary, contact a qualified service representative to per-
form the replacement.
Warning: Do not attempt to recharge, disassemble, or
incinerate this type of battery. Keep all batteries away
from children. Dispose of used batteries promptly and as
regulated by applicable laws. Note: In some areas, the
servicer is required by law to return the defective parts.
However, you do have the option of having the servicer
dispose of these parts for you.
Disposal Notice: Should this product become damaged
beyond repair, or for some reason its useful life is consid-
ered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products
that contain lead, batteries, plastics, etc.
NOTICE: Service charges incurred due to lack of knowl-
edge relating to how a function or effect works (when the
unit is operating as designed) are not covered by the
manufacturer’s warranty, and are therefore the owners
responsibility. Please study this manual carefully and con-
sult your dealer before requesting service.
NAME PLATE LOCATION: The graphic below indi-
cates the location of the name plate. The model number,
serial number, power requirements, etc., are located on
this plate. You should record the model number, serial
number, and the date of purchase in the spaces provided
below and retain this manual as a permanent record of
your purchase.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
PRODUCT SAFETY MARKINGS: Yamaha electronic
products may have either labels similar to the graphics
shown below or molded/stamped facsimiles of these
graphics on the enclosure. The explanation of these graph-
ics appears on this page. Please observe all cautions indi-
cated on this page and those indicated in the safety in-
struction section.
The exclamation point within the equi-
lateral triangle is intended to alert the
user to the presence of important oper-
ating and maintenance (servicing) in-
structions in the literature accompany-
ing the product.
The lightning flash with arrowhead
symbol, within the equilateral triangle,
is intended to alert the user to the pres-
ence of uninsulated “dangerous volt-
age” within the product’s enclosure that
may be of sufficient magnitude to con-
stitute a risk of electrical shock.
IMPORTANT NOTICE: All Yamaha electronic prod-
ucts are tested and approved by an independent safety
testing laboratory in order that you may be sure that when
it is properly installed and used in its normal and custom-
ary manner, all foreseeable risks have been eliminated.
DO NOT modify this unit or commission others to do so
unless specifically authorized by Yamaha. Product per-
formance and/or safety standards may be diminished.
Claims filed under the expressed warranty may be denied
if the unit is/has been modified. Implied warranties may
also be affected.
SPECIFICATIONS SUBJECT TO CHANGE: The
information contained in this manual is believed to be
correct at the time of printing. However, Yamaha reserves
the right to change or modify any of the specifications
without notice or obligation to update existing units.
SPECIAL MESSAGE SECTION
Rear Panel
Before moving the instrument, remove all connected cables.
When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,
solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do not
place vinyl or plastic objects on the instrument, since this might discolor the panel.
Do not rest your weight on, or place heavy objects on the instrument, and do
not use excessive force on the buttons, switches or connectors.
Do not place objects in front of the instrument's air vent, since this may
prevent adequate ventilation of the internal components, and possibly result
in the instrument overheating. To ensure adequate ventilation and cooling,
leave at least 10cm of open space behind the A3000 rear panel, and at least
4cm of open space above the top cover.
Do not operate the instrument for a long period of time at a high or uncom-
fortable volume level, since this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the ears, consult a physician.
SAVING USER DATA
To protect against data loss caused by malfunction or operating error, be sure
to save your data regularly to floppy disk, hard disk or other storage medium.
Yamaha cannot be held responsible for damage caused by improper use or modi-
fications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
This instrument contains no user-serviceable parts. Do not attempt to disas-
semble or modify the internal components in any way.
Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill
into any openings.
If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the instrument, or if any unusual smells or
smoke should appear to be caused by it, immediately turn off the power
switch, disconnect the electric plug from the outlet, and have the instrument
inspected by qualified Yamaha service personnel.
Only use the voltage specified as correct for the instrument. The required
voltage is printed on the name plate of the instrument.
Always connect the three-pin attachment plug to a properly grounded power
source. (For more information about the main power supply, see “Connect-
ing the Power.)
Before cleaning the instrument, always remove the electric plug from the
outlet. Never insert or remove an electric plug with wet hands.
Check the electric plug periodically and remove any dirt or dust which may
have accumulated on it.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the
instrument or other property. These precautions include, but are not limited to, the following:
Do not place the power cord near heat sources such as heaters or radiators,
and do not excessively bend or otherwise damage the cord, place heavy
objects on it, or place it in a position where anyone could walk on, trip over,
or roll anything over it.
When removing the electric plug from an outlet, always hold the plug itself
and not the cord. Pulling by the cord can damage it.
Do not connect the instrument to an electrical outlet using a multiple-con-
nector. Doing so can result in lower sound quality, or possibly cause over-
heating in the outlet.
• Remove the electric plug from the outlet when the instrument is not to be
used for extended periods of time, or during electrical storms.
Before connecting the instrument to other electronic components, turn off
the power for all components. Before turning the power on or off for all
components, set all volume levels to minimum.
Do not expose the instrument to excessive dust or vibrations, or extreme cold or
heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent
the possibility of panel disfiguration or damage to the internal components.
Do not use the instrument near other electrical products such as televisions,
radios, or speakers, since this might cause interference which can affect
proper operation of the other products.
Do not place the instrument in an unstable position where it might acciden-
tally fall over.
Handling and Installation of Options
CAUTION
Before handling an option board, hard disk, or SIMM, you should briefly touch
the A3000 metal casing (or other such metallic area) with your bare hand so as
to drain off any static charge from your body. Note that even a slight amount of
electrostatic discharge may cause damage to these components.
It is recommended that you wear gloves to protect your hands from metallic
projections on the A3000, hard disk, SIMMs, option boards, and other com-
ponents. Touching leads or connectors with bare hands may cause finger
cuts, and may also result in poor electrical contact or electrostatic damage.
Take care to avoid dropping screws into the A3000 unit. If a screw does
fall in, be sure to remove it before you reassemble and power up the unit.
Starting the unit with a loose screw inside may lead to improper opera-
tion or equipment failure. (If you are unable to retrieve a dropped screw,
consult your Yamaha dealer for advice.)
WARNING
• Before beginning installation, switch off the power to the A3000 and
connected peripherals, and unplug them from the power outlet. Then
remove all cables connecting the A3000 to other devices. (Leaving the
power cord connected while working can result in electric shock. Leav-
ing other cables connected can interfere with work.)
Do not disassemble, modify, or apply excessive force to board areas and
connectors on option boards, hard disk, and SIMMs. Bending or tam-
pering with boards and connectors may lead to electric shock, fire, or
equipment failures.
* Consult your Yamaha dealer if you have any questions regarding installation procedures for options boards, hard disks, SIMMs, or other optional devices.
* If SIMM memory, hard disk, or other optional component fails to work properly, consult the item's dealer for advice.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,
short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Features
2
Features
Versatile Professional Sampler
The A3000 professional sampler is an ideal break-beat
machine and phrase sampler for a wide variety of re-
cording and performance applications.
Excellent Effects System
The A3000’s triple-block effect system lets you set up
as many as three independent effects. Select from a wide
range of built-in effects — including original effects
custom-designed to heighten the performance quali-
ties of phrase and break-beat play. You can also apply
effects to incoming signals as you record them, and to
analog input that you feed through the A3000 for
realtime output.
Easy to Use
The A3000 presents its editing and control capabilities
in an easy-to-use three-level arrangement. All opera-
tions are handled using front-panel mode buttons, func-
tion keys, and knobs. You can access and edit any set-
ting by selecting the mode, then selecting the func-
tion, and then turning the knobs directly under the
screen. It is also possible to use knobs and function
keys to control realtime playback.
Performance-Enhancing Options
Installation of the optional I/O expansion board (AIEB1
board) adds digital I/O capability plus six additional as-
signable-output pairs to your A3000. The A3000 also
accepts up to 128MB of expansion memory.
List of Accessories
Your A3000 package includes the following accessories. Make sure that all of these accessories are included.
CD-ROM
Power cord
MIDI cable
Five floppy disks
Owner’s Manual
Power supply cable for hard disk (red/white 4-wire cable)
SCSI cable for hard disk
* If any of the above items is missing, please contact your Yamaha dealer for assistance.
Unauthorized copying of copyrighted software for purposes other than purchaser’s personal use is prohibited.
Features
3
PROFESSIONAL SAMPLER
Owners Manual
Thank you for your purchase of the Yamaha A3000 Professional Sampler. The A3000
incorporates a leading-edge AWM2 tone generator, and is an ideal for use with synthesiz-
ers, MIDI keyboards, and other MIDI devices in a wide variety of musical applications.
This owner’s manual will help you get the most from your A3000’s many advanced fea-
tures. Please read through the essential parts of the manual carefully before beginning
work with your sampler, and refer back to the manual for additional information as
necessary. Please be sure to store the manual in a safe and handy location.
Contents
4
Using the Manual .............................................................................. 6
Panel and Connector Arrangement .................................................. 8
A3000 Options ................................................................................. 14
Handling the Floppy Disk Drive(FDD) and Floppy Disk ............... 16
Chapter 1 Setting Up
Setting Up........................................................................................ 20
Connecting the Power .................................................................... 21
Connecting the A3000 Outputs ...................................................... 22
Connecting the Audio Inputs ......................................................... 25
MIDI Connections ........................................................................... 27
Power ON/OFF ................................................................................ 30
Sound Check ................................................................................... 32
Chapter 2 Trying It Out
Introduction .................................................................................... 36
Starting Out .................................................................................... 38
Next Step ......................................................................................... 45
Sample Editing................................................................................ 52
Program Editing ............................................................................. 57
Sequence Play ................................................................................. 62
Saving and Reloading Your Data .................................................... 64
Accompanying Disks ....................................................................... 68
Chapter 3 Basics
Samples and Programs ................................................................... 70
Sample Output Destinations and Effects ....................................... 78
Data Configuration and Handling .................................................. 80
Modes and Functions ...................................................................... 84
Basic Operation ............................................................................... 86
Other Keys and Operations ............................................................. 91
Chapter 4 PLAY Mode
Play Mode ........................................................................................ 94
Program & Sample Selection Screen ............................................. 95
PROGRAM/SAMPLE Selection Screen ................................................... 95
COMMAND Pages ............................................................................ 98
SAVE ........................................................................................................ 98
INIT (Program Initialization) ............................................................... 101
COPY ..................................................................................................... 102
PGMDUMP (Program Dump) .............................................................. 103
SETINIT (Set Program’s Initial Conditions)........................................ 104
NEWBANK (Create a Sample Bank) ..................................................... 105
DELETE ................................................................................................ 106
DUPL (Duplicate) .................................................................................. 107
SMPDUMP (Sample Dump) .................................................................. 108
PROGRAM Function ..................................................................... 110
PROGRAM - PgmSel (Select Program) ................................................ 110
SAMPLE Function ........................................................................ 112
SAMPLE - SmpSel (Select Sample)...................................................... 112
SAMPLE - SmpBnk (Select Sample from Sample Bank) .................... 114
SAMPLE - ToBank (Assign Sample to Bank) ....................................... 115
SAMPLE - SmpSort (Sort Samples) ..................................................... 117
EASY EDIT Function .................................................................... 118
EASY EDIT - EasyEd ............................................................................. 119
EFFECT Function ......................................................................... 121
EFFECT - EfType (Select the Effect Types) .......................................... 121
EFFECT - Efct1,...,Efct3 (Edit the Effects) .......................................... 124
EFFECT - In&Out (Input/output levels and pan) ................................ 126
EFFECT - EdType (Effect Edit Type) .................................................... 127
SETUP Function ........................................................................... 128
SETUP - PgmMstr (Program’s Master Settings) .................................. 128
SETUP - Portmnt (Portamento) ........................................................... 130
SETUP - ADSetup (A/D-In Setup) ........................................................ 132
SETUP - ADOut (Output Setup for A/D-Input Signal) ........................ 134
CONTROL Function...................................................................... 136
CONTROL - PgmCtl1 (Program Controller Setup 1) .......................... 136
CONTROL - PgmCtl2 (Program Controller Setup 2) .......................... 139
CONTROL - Reset (Controller Reset) ................................................... 141
Chapter 5 EDIT Mode
EDIT Mode .................................................................................... 144
COMMAND Pages .......................................................................... 147
SAVE ...................................................................................................... 147
REVERT ................................................................................................. 149
NORM (Normalize) ............................................................................... 150
RESMPL - TmStrch (Resampling - Time Stretch) .............................. 151
RESMPL - PtchCnv (Resampling - Pitch Conversion) ........................ 153
FADE ..................................................................................................... 155
REVERS (Reverse) ................................................................................ 157
LOOPXFD (Loop Crossfade) ................................................................. 158
SETINIT (Register Initial Parameter Values)....................................... 160
TRIM/LOOP Function ................................................................... 161
TRIM/LOOP - Config (Configure)......................................................... 161
TRIM/LOOP - Wave (Edit Waveform) ................................................... 164
TRIM/LOOP - Loop (Edit Loop Addresses) ........................................... 166
TRIM/LOOP - WvMode (Set Wave Mode) ............................................. 168
MAP/OUT Function ....................................................................... 170
MAP/OUT - KeyRnge (Key Range) ........................................................ 170
MAP/OUT - VelRnge (Velocity Range) .................................................. 172
MAP/OUT - Lvl&Mode ........................................................................... 174
MAP/OUT - Output ................................................................................ 176
MAP/OUT - Pitch ................................................................................... 178
MAP/OUT - Expand ............................................................................... 179
MAP/OUT - LvlScale (Level Scaling) .................................................... 180
FILTER Function .......................................................................... 182
FILTER - Filter ...................................................................................... 182
FILTER - FltSens (Filter Sensitivity) ................................................... 184
FILTER - FltScale (Filter Scaling) ........................................................ 185
FILTER - EQ (Equalization) ................................................................. 187
EG Function .................................................................................. 188
EG - AEG (Amplitude Envelope Generator)......................................... 188
EG - AEGMode (AEG Mode Settings) ................................................... 190
EG - FEGRate (Filter-EG Rates) ........................................................... 192
EG - FEGLevel (Filter-EG Levels) ........................................................ 194
EG - FEGMode (FEG Mode Settings) ................................................... 196
EG - PEGRate (Pitch-EG Rates) ........................................................... 198
EG - PEGLevel (Pitch-EG Levels) ........................................................ 200
Contents
Contents
5
EG - PEGMode (PEG Mode Settings) ................................................... 201
LFO Function ................................................................................ 203
LFO - Common ..................................................................................... 203
LFO - FltrMod (Filter Modulation) ...................................................... 205
LFO - PtchMod (Pitch Modulation)...................................................... 206
LFO - AmpMod (Amplitude Modulation) ............................................. 207
MIDI/CTRL Function .................................................................... 208
MIDI/CTRL - RCh&Alt (Receive Channel and Alternate ..................... 208
MIDI/CTRL - SmpCtl1 (Sample Controller Setup 1) ........................... 210
MIDI/CTRL - SmpCtl2 (Sample Controller Setup 2) ........................... 213
MIDI/CTRL - Vel&PB (Velocity and Pitchbend) ................................... 215
Chapter 6 RECORDING Mode
RECORDING Mode ....................................................................... 220
COMMAND Page ........................................................................... 221
SAVE ...................................................................................................... 221
RECORD Function ........................................................................ 223
RECORD - Record ................................................................................. 223
SETUP Function ........................................................................... 227
SETUP - RecData .................................................................................. 227
SETUP - Target...................................................................................... 230
SETUP - KeyRnge ................................................................................. 232
SETUP - Trigger .................................................................................... 234
SETUP - Process.................................................................................... 235
METER Function .......................................................................... 236
METER - Meter ..................................................................................... 236
METER - TrgLvl .................................................................................... 237
EFFECT Function ......................................................................... 238
EFFECT - EfType (Select the Effect Types) ........................................ 238
EFFECT - RecEf1,...,RecEf3 (Edit the Effects) .................................... 239
EFFECT - In&Out (Input/output levels and pan)................................ 240
EFFECT - EdType (Effect Edit Type) .................................................... 240
EXT CTRL Function ..................................................................... 241
EXT CTRL - CD-ROM ........................................................................... 241
EXT CTRL - CD-DA ............................................................................... 242
MONITOR Function ...................................................................... 243
MONITOR - Monitor ............................................................................. 243
MONITOR - Click .................................................................................. 245
Chapter 7 DISK Mode
DISK Mode .................................................................................... 248
COMMAND Pages .......................................................................... 249
LOAD ..................................................................................................... 249
DELETE ................................................................................................ 250
COPY ..................................................................................................... 251
FORMAT ................................................................................................ 252
PHYS_FMT (Physical Format) ............................................................. 254
PART_FMT (Format a Partition) .......................................................... 256
FD_FMT (Format a Floppy Disk) ......................................................... 258
PROGRAM Function ..................................................................... 259
PROGRAM - PgmLoad (Load Program(s)) ........................................... 259
SAMPLE Function ........................................................................ 261
SAMPLE - SmpLoad (Load Sample(s)) ................................................ 261
SEQUENCE Function ................................................................... 264
SEQUENCE - SeqLoad (Load Sequence(s)) ......................................... 264
VOLUME Function ........................................................................ 266
VOLUME - Volume ................................................................................ 266
DISK Function .............................................................................. 268
DISK - Disk ........................................................................................... 268
DISK - Config (Configure) .................................................................... 270
DISK - SelfID ........................................................................................ 271
IMPORT Function ......................................................................... 272
IMPORT - ImpSmp (Import a sample)................................................. 272
IMPORT - ImpVce (Import a voice) ...................................................... 274
IMPORT - ImpOthr (Import Other Data Type) .................................... 276
Chapter 8 UTILITY Mode
UTILITY Mode ............................................................................... 280
COMMAND Pages .......................................................................... 281
SAVE ...................................................................................................... 281
DELETE ................................................................................................ 283
SAVESYS (Save System Settings)......................................................... 284
LOADSYS (Load System Settings) ....................................................... 285
ALLDUMP (Data Dump) ....................................................................... 286
TOTAL EQ Function ..................................................................... 287
Total EQ - Gain...................................................................................... 288
Total EQ - Freq ...................................................................................... 289
Total EQ - Width ................................................................................... 290
PANEL PLAY Function.................................................................. 291
PANEL PLAY - KnobCtl (Knob Control) .............................................. 291
PANEL PLAY - KnobSet ........................................................................ 292
PANEL PLAY - FKeySet (Set Function Keys) ....................................... 294
SEQUENCE Function ................................................................... 296
SEQUENCE - SeqSel (Select Sequence) .............................................. 296
SEQUENCE - Play&Rec (Playback and Recording) ............................. 297
MASTER Function ........................................................................ 298
MASTER - Tuning ................................................................................. 298
MASTER - StOut (Stereo Output Assignment) .................................... 299
SYSTEM Function ........................................................................ 300
SYSTEM - Keys ..................................................................................... 300
SYSTEM - Display ................................................................................. 302
SYSTEM - Page ..................................................................................... 303
SYSTEM - FreeMem .............................................................................. 304
MIDI Function .............................................................................. 305
MIDI - Receive ....................................................................................... 305
MIDI - Adjust ......................................................................................... 307
MIDI - RcvFlt (Receiving Filter) ........................................................... 309
MIDI - Bulk (Bulk Dump) ..................................................................... 310
Appendix
Installing SIMMs ........................................................................... 312
Installing the AIEB1 I/O Expansion Board .................................. 316
Setting the SCSI Board Terminator Switch ................................. 320
Installing an Internal Hard Disk .................................................. 323
Connecting external SCSI devices................................................ 328
Specifications ................................................................................ 332
Effect type list ............................................................................... 335
Effect parameter list ..................................................................... 337
Control change number list ......................................................... 347
Troubleshooting ............................................................................ 348
Error messages.............................................................................. 351
MIDI data format........................................................................... 352
Index
Index .............................................................................................. 364
Using the Manual
6
Using the Manual
Manual Organization
This manual comprises eight chapters and an Appendix. Chapters 1 and 3 contain es-
sential information and should be read carefully. You may also wish to run through the
brief tutorial given in Chapter 2 before beginning serious work with the A3000.
Chapters 4 through 8 provide detailed information about each of the five operating
modes. Refer to this information as needed while working with the A3000.
Chapter 1 Setting Up
This chapter explains the A3000’s controls and connectors, and shows how to connect
up speakers and MIDI devices. Please read through this chapter before you start to work
with the A3000.
Chapter 2 Trying It Out
This chapter guides you through a trial run with the A3000. Going through these proce-
dures will help you get a good feel for basic A3000 operations.
Chapter 3 Basics
The chapter introduces basic concepts, terminology, and operating procedures. Read
this chapter to learn about samples, sample banks, programs, and sequences; modes
and functions; screen displays; and other important features.
Chapter 4 PLAY Mode
This chapter explains all PLAY-mode functions. You use PLAY mode to edit and play
programs.
Chapter 5 EDIT Mode
This chapter explains all EDIT-mode functions. You use EDIT mode to edit your samples
and sample banks.
Chapter 6 RECORDING Mode
This chapter explains all RECORDING-mode functions. You use RECORDING mode to
record samples and sequences.
Chapter 7 DISK Mode
This chapter explains all DISK-mode functions. You use DISK mode to manage your
floppy and hard disks.
Chapter 8 UTILITY Mode
This chapter explains all UTILITY-mode functions. You use UTILITY mode to set the
system’s environment.
Appendix
Provides option installation instructions, troubleshooting advice, error-message descrip-
tions, A3000 specifications, and MIDI information.
Using the Manual
7
Finding the Information You Need
You can use any of the following methods to locate information within this manual.
Use the
Contents
.
Check the Contents on pages 4 to 6.
Use the Index.
Refer to the Index on pages 363 to 367.
Refer to
Panel and Connector Arrangement
.
Go to the “Panel and Connector Arrangement” section (pages 8 to 14) and locate the
knob, key, or other component that you require information about. Then refer to the
indicated page.
Leaf through the manual.
Page through sections related to the feature you need information about. Note that
each page has a header indicating the page’s contents, and a footer indicating the chap-
ter name.
Icons
This manual uses the following icons to call attention to specific types of information.
Important: An important note or precaution intended to help you avoid
loss of data or other major inconvenience. Always read these notices care-
fully.
FYI (For Your Information): Reference information indirectly related to
the content of the main text. May contain practical advice or general sup-
plementary information.
Procedure: Step-by-step instructions for carrying out a particular opera-
tion. A mark within a procedure indicates the result produced by carry-
ing out the immediately preceding instruction.
xx Page reference. Directs you to another page for related information.
Screen illustrations and other drawings within this manual are for explanatory pur-
poses only, and may in some cases differ from actual displays and configurations.
Panel and Connector Arrangement
8
MASTER VOL REC VOL
PHONES L INPUT R
1 2 3 4 5
(5)(2)
(1)
(3)
(4)
(7)(6)
Panel and Connector Arrangement
Front Panel (Left Side)
(1) MASTER VOL (Master Volume)
Adjusts the output level at the STEREO OUT connectors only. This knob does not affect
the output level at the ASSIGNABLE OUT connectors, or at the various connectors
provided on the optional I/O expansion board (AIEB1 board).
Panel and Connector Arrangement
9
(2) REC VOL (Recording Volume)
Adjusts the input level from the front panel’s INPUT L and INPUT R jacks. Use the knob
to adjust the level when recording a sample, or when passing an input signal directly
through the A3000 outputs for realtime output (“A/D In” feature).
This knob does not affect the input level to the DIGITAL IN and OPTICAL IN connectors
on the optional I/O expansion board (AIEB1 board).
(3) PHONES jack
Connects to a set of stereo headphones. The PHONES jack always produces the same
signal as the STEREO OUT jacks. Note that headphone impedance should be between
16 and 150 ohms.
(4) INPUT L, INPUT R jacks
Use these jacks to input an analog signal for recording, or for realtime output (“A/D In”
feature). Use the INPUT L jack if you are supplying a monaural signal.
(5) Display
The display indicates the status and settings for the currently selected function, and
presents messages and confirmation prompts. When you are working at a parameter-
setting page, the top line of the display indicates the parameter names, while the bot-
tom line shows the current values. The names and values appear directly over the knobs
that you use to make the settings.
(6) Knob “push” lamps
The lamp above the knob lights up to indicate that the knob can be pushed to execute
some action. If the lamp is off, pushing the knob has no effect.
(7) Knobs
You use the knobs to set the various parameter values, to switch display pages, and
execute operations. In most cases you turn the knob to set a value, and push the knob to
execute an operation — for example, to start or stop recording. Knobs are numbered 1
to 5.
Panel and Connector Arrangement
10
Front Panel (Right Side)
(1) Mode buttons
The A3000 provides five operating modes. You select the mode by pressing the corre-
sponding mode button. The button lamp comes on to indicate that the mode is selected.
Each mode is further divided into six functions. After selecting the mode, you can switch
among its functions by pressing the appropriate function keys.
(The A3000 also uses the button lamps to let you know that it is receiving MIDI data.
Each lamp corresponds to a different MIDI data type, and will continue to blink while
the A3000 is receiving MIDI data of that type. (92))
(2) Function keys
Use these keys to switch among the six functions within the currently selected mode.
(3) COMMAND key
You press the COMMAND key to access additional commands relevant to the mode and
function that you are currently working in. (91)
PLAPLAYY
EDITEDIT
RECREC
DISKDISK
UTILITYUTILITY
PROGRAMPROGRAM
TRIM/LOOPTRIM/LOOP
RECORDRECORD
PROGRAMPROGRAM
TTOTOTALAL EQ EQ
SAMPLESAMPLE
MAP/OUTMAP/OUT
SETUPSETUP
SAMPLESAMPLE
PPANELANEL PLA PLAYY
EASYEASY EDIT EDIT
FILFILTERTER
METERMETER
SEQUENCESEQUENCE
SEQUENCESEQUENCE
EFFECTEFFECT
EGEG
EFFECTEFFECT
VOLUMEVOLUME
MASTERMASTER
SETUPSETUP
LFOLFO
EXITEXIT CTRL CTRL
DISKDISK
SYSTEMSYSTEM
CONTROLCONTROL
MIDI/CTRLMIDI/CTRL
MONITMONITOROR
IMPORIMPORTT
MIDIMIDI
COMMAND ASSIGNABLE AUDITION
POWERPOWER
ON/ON/ OFFOFF
(1)
(2)
(7)
(6)(5)(4)(3)
Panel and Connector Arrangement
11
(4) ASSIGNABLE key
You can assign this key any of four different functions. You can set it to operate as a
damp key (so that it switches all sound off), as a controller reset button, or as a toggle
for the knob-controller feature (knobs act as controllers) or the function-key playback
feature (function keys act as MIDI keys). (91)
(5) AUDITION key
Press the key to play out the currently selected sample. You use this feature to check the
sound of the sample while editing.
(6) Floppy-disk drive
Accepts a 3.5-inch floppy disk. You can use floppy disks to save and reload your data
(programs, samples, sequences, and system settings).
Note that there is an access lamp at the lower left of the drive. The lamp lights up while
the disk is being accessed. Please do not eject the floppy-disk while this lamp is on.
To eject a disk, press the EJECT button at the lower right of the drive.
(7) POWER switch
Press once to switch the power on. Press again to turn the power off.
Important
The A3000 stores all new data into main memory only, and will lose all of this data when
you switch off the power. You must therefore be sure to save all important data to disk
before turning the A3000 off.
Panel and Connector Arrangement
12
Rear Panel
(1) AC inlet
Connects to the AC power cord supplied with the A3000. (Please do not use any other
power cord with this unit.)
(2) MIDI connectors
These connectors link the A3000 to external MIDI devices. The MIDI IN connector re-
ceives MIDI signals, while the MIDI OUT connector transmits MIDI data generated by
the A3000. The MIDI THRU connector relays the MIDI signals received at the MIDI IN
connector.
(3) ASSIGNABLE OUT jacks
Analog output jacks. These jacks operate independently of the STEREO OUT jacks. You
can use these jacks to output the sound of one or more selected samples, or to output
the signal supplied through the front panel’s analog input connectors (134, 176). You
may also set them so that they output the same signal as the STEREO OUT jacks (299).
(4) STEREO OUT jacks
These are the main analog output jacks.
(5) SCSI connector
This is a half-pitch 50-pin connector. You use it to connect up a SCSI hard drive, CD-
ROM drive, or other SCSI device.
(1) (2)
(3) (4)
(5)
Panel and Connector Arrangement
13
Rear Panel (with optional AIEB1 board installed)
(1) (2) (3)
(1) OPTICAL IN, OUT connectors
Use these connectors to input or output digital signals over optical-fiber cable. You can
use the OPTICAL IN to record a digital signal of frequency 48kHz, 44.1kHz, or 32kHz.
The OPTICAL OUT connector outputs a digital signal of frequency 44.1kHz.
(2) DIGITAL IN, OUT connectors
Use these connectors to input or output digital signals over coaxial (RCA-pin) cable. The
digital signal format is CD/DAT (S/P DIF).
You can use the DIGITAL IN connector to record a digital signal of frequency 48kHz,
44.1kHz, or 32kHz. The DIGITAL OUT connector outputs a digital signal of frequency
44.1kHz.
(3) ASSIGNABLE OUT jacks (AS1 to AS6)
Additional analog output jacks. Each pair (1&2, 3&4, 5&6) operates independently of all
other outputs on the A3000. You can use these jacks to output the sound of one or more
selected samples, or to output the signal supplied through the front panel’s analog in-
put connectors (134, 176). You may also set them so that they output the same signal
as the STEREO OUT jacks (299).
A3000 Options
14
A3000 Options
You can enhance the capability of your A3000 by installing options. The A3000 supports
two options: (1) additional memory, and (2) the AIEB1 board (I/O expansion board).
Expansion Memory (SIMMs)
The A3000 stores all active data in main memory. To play a sample back, you must first
load it into main memory. And whenever you record a sample, you must record it into
main memory.
Samples consume a great deal of memory. The A3000 comes standard with 2 megabytes
(2MB) of memory — but this is only sufficient to store about 23 seconds of high-quality
monaural sound (at 44.1kHz sampling frequency), or approximately 11.5 seconds of
stereo sound.
You can increase this capacity by installing additional memory. The A3000 accepts ex-
pansion memory in the form of SIMMs (single in-line memory modules). Using SIMMs,
you can install up to 128MB of memory onto the A3000. SIMMs can be purchased from
almost any computer-supply dealer.
Adding memory will allow you to record longer samples, and to work with more sam-
ples at the same time. For information about how to install SIMMs, refer to the Appen-
dix. (312)
Important
You need to use 72-pin SIMMs with access time of 70ns or less. The SIMM module
size may be 4MB, 8MB, 16MB, or 32MB. The A3000 is designed for use with 32-bit
SIMMs, but can also accept installation of 36-bit (parity-type) SIMMs.
SIMMs must be installed in pairs: you can install either two SIMMs or four SIMMs.
Both modules in a pair must have the same memory capacity.
The A3000 ships with 2MB of sampling memory installed, and is capable of accessing
up to 128MB. If you add one pair of 32MB SIMMs, for example, you increase the
available sampling memory to a total of (2 + 32×2 =) 66MB. If you install four 32MB
SIMMs, however, the sampling memory size becomes 128MB (and the original 2MB
are effectively disabled).
For more information about SIMM purchase, refer to your A3000 dealer.
A3000 Options
15
The I/O Expansion Board (AIEB1 Board)
In its standard configuration, the A3000 supports analog I/O only. Although it stores all
internal data in digital form, it does not provide direct digital I/O connectors.
You can add digital I/O capacity by installing an AIEB1 board. The board offers two
different digital connector types: optical connectors, and coaxial connectors. As an added
benefit, the board also includes three stereo ASSIGNABLE OUTPUT pairs (six analog
jacks), which operate independently of the standard STEREO OUT and ASSIGNABLE
OUT jacks.
For information about how to install this board, refer to the Appendix. (312)
Handling the Floppy Disk Drive(FDD) and Floppy Disk
16
Handling the Floppy Disk Drive(FDD) and Floppy Disk
Precautions
Be sure to handle floppy disks and treat the disk drive with care. Follow the important
precautions below.
Disk Type
The A3000 disk drive accepts 2HD-type and 2DD-type 3.5" floppy disks.
Inserting/Ejecting Floppy Disks
To insert a floppy disk into the disk drive:
Hold the disk so that the label of the disk is facing upward and the sliding shutter is
facing forward, towards the disk slot. Carefully insert the disk into the slot, slowly push-
ing it all the way in until it clicks into place and the eject button pops out.
To eject a floppy disk:
Before ejecting the disk, be sure to confirm that the FDD is stopped (check if the LED
below the floppy disk slot is off).
Press the eject button slowly as far as it will go; the disk will automatically pop out.
When the disk is fully ejected, carefully remove it by hand.
Never attempt to remove the disk or turn the power off during reading or writing. Do-
ing so can damage the disk and possibly the disk drive.
If the eject button is pressed too quickly, or if it is not pressed in as far as it will go, the
disk may not eject properly. The eject button may become stuck in a half-pressed posi-
tion with the disk extending from the drive slot by only a few millimeters. If this hap-
pens, do not attempt to pull out the partially ejected disk, since using force in this
situation can damage the disk drive mechanism or the floppy disk. To remove a partially
ejected disk, try pressing the eject button once again, or push the disk back into the slot
and then repeat the eject procedure.
Be sure to remove the floppy disk from the disk drive before turning off the power. A
floppy disk left in the drive for extended periods can easily pick up dust and dirt that can
cause data read and write errors.
Handling the Floppy Disk Drive(FDD) and Floppy Disk
17
Cleaning the Disk Drive Read/Write Head
Clean the read/write head regularly. This instrument employs a precision magnetic
read/write head which, after an extended period of use, will pick up a layer of mag-
netic particles from the disks used that will eventually cause read and write errors.
To maintain the disk drive in optimum working order Yamaha recommends that you
use a commercially-available dry-type head cleaning disk to clean the head about
once a month. Ask your Yamaha dealer about the availability of proper head-cleaning
disks.
Never insert anything but floppy disks into the disk drive. Other objects may cause
damage to the disk drive or floppy disks.
About the Floppy Disks
To handle floppy disks with care:
Do not place heavy objects on a disk or bend or apply pressure to the disk in any way.
Always keep floppy disks in their protective cases when they are not in use.
Do not expose the disk to direct sunlight, extremely high or low temperatures, or exces-
sive humidity, dust or liquids.
Do not open the sliding shutter and touch the exposed surface of the floppy disk inside.
Do not expose the disk to magnetic fields, such as those produced by televisions, speak-
ers, motors, etc., since magnetic fields can partially or completely erase data on the
disk, rendering it unreadable.
Never use a floppy disk with a deformed shutter or housing.
Do not attach anything other than the provided labels to a floppy disk. Also make sure
that labels are attached in the proper location.
To protect your data (Write-protect Tab):
To prevent accidental erasure of important data, slide the disk’s write-protect tab to the
“protect” position (tab open).
Data backup
For maximum data security Yamaha recommends that you keep two copies of impor-
tant data on separate floppy disks. This gives you a backup if one disk is lost or damaged.
18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376

Yamaha A3000 Návod k obsluze

Kategorie
Hudební vybavení
Typ
Návod k obsluze