Yamaha R-S300 Návod k obsluze

©

2010 Yamaha Corporation

Receiver

Ampli-Tuner

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

Printed in Malaysia WV17430-2

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around this unit.

Top: 30 cm (11-3/4 in)

Rear: 20 cm (7-7/8 in)

Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press A to turn off this unit, and

then disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

20 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

This label is required to be attached to a product of which

the temperature of the top cover may be hot during

operation.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn off this

unit by A or set it to the standby mode by A button on the remote

control. In this state, this unit is designed to consume a very small

quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

English

USEFUL FEATURES ............................................ 2

SUPPLIED ACCESSORIES ................................. 3

CONTROLS AND FUNCTIONS ......................... 4

Front panel................................................................. 4

Front panel display .................................................... 6

Rear panel.................................................................. 7

Remote control........................................................... 8

Using the remote control ........................................... 9

CONNECTIONS .................................................. 10

Connecting speakers and source components.......... 10

Connecting the FM and AM antennas..................... 12

Connecting power cable .......................................... 12

PLAYING AND RECORDING .......................... 13

Playing a source....................................................... 13

Adjusting the tonal quality....................................... 14

Recording a source .................................................. 16

Using the sleep timer ............................................... 16

FM/AM TUNING ................................................. 17

Automatic tuning ..................................................... 17

Manual tuning.......................................................... 18

Automatic station preset (FM stations only) ........... 19

Manual station preset...............................................20

Recalling a preset station......................................... 21

Clearing a preset station........................................... 21

Clearing all preset stations....................................... 22

Receiving Radio Data System information

(FM stations only) ............................................... 23

TP Search function (FM stations only).................... 24

PLAYING BACK TUNES

FROM YOUR iPhone/iPod/

Bluetooth™ COMPONENT............................ 25

Using a Universal Dock for iPod............................. 26

Using a Wireless System for iPod ........................... 27

Using a Bluetooth Wireless Audio Receiver........... 28

SETTING THE OPTION MENU

FOR EACH INPUT SOURCE.........................30

Option menu items................................................... 30

ADVANCED SETUP ............................................32

Changing the ADVANCED SETUP

menu parameters.................................................. 32

TROUBLESHOOTING .......................................33

SPECIFICATIONS...............................................38

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

USEFUL FEATURES

2 En

This unit allows you to:

*

Optional Yamaha product required

iPhone, iPod

iPhone, iPod, iPod classic, iPod nano and iPod touch are trademarks of Apple Inc., registered in the U.S. and other

countries.

Bluetooth™

Bluetooth is a registered trademark of the Bluetooth SIG and is used by Yamaha in accordance with a license agreement.

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the front panel of this unit or those on the remote controls. In case

the button names differ between this unit and the remote controls, the names of the buttons on the remote controls are given in

parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

USEFUL FEATURES

Improve sound quality by using the Pure Direct function

➡

p. 14

Play back music from your iPhone/iPod

*

or Bluetooth component

*

➡

p. 25

Listen to FM and AM radio stations

➡

p. 17

Receive and display Radio Data System information

➡

p. 23

Boost bass sounds by connecting a subwoofer

➡

p. 10

Use this unit’s remote control to operate a Yamaha CD player

➡

p. 8

Save power by using the automatic power down function

➡

p. 32

INTRODUCTION

SUPPLIED ACCESSORIES

3 En

INTRODUCTION

English

Please check that you received all of the following parts.

■ Notes on remote control and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Use AA, R6, UM-3 batteries for the remote control.

• Insert batteries according to the polarity markings (+ and -).

• Change all batteries if you notice the operation range of the remote control narrows.

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth, rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Do not use old batteries together with new ones. This may shorten the life of the new batteries or cause old batteries to leak.

• Do not use different types of batteries (such as alkaline and manganese batteries) together. Batteries that look the same may have a

different specification.

• Before inserting new batteries, wipe the battery compartment clean.

• Dispose of batteries according to your regional regulations.

SUPPLIED ACCESSORIES

Remote control

Indoor FM antenna

AM loop antenna

Batteries (x2)

(AA, R6, UM-3)

CONTROLS AND FUNCTIONS

4 En

1 A (power)

Turns on and off the power of this unit (see page 13).

On position: Pushed inward

Off position: Released outward

This unit consumes a small amount of power even when turned

off or when in standby mode.

2 Power indicator

Lights up as follows:

Brightly lit: Power is on

Dimly lit: Standby mode

Off: Power is off

If an iPhone/iPod is charged while this unit is in standby mode,

the power indicator lights up brightly.

3 SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the rear

panel each time the corresponding button is pressed (see

page

13

).

4 TP

Searches automatically for a station that provides traffic

program (TP) broadcasts (see page 24).

5 INFO

Turns on and changes the Radio Data System display

mode when TUNER is selected as the input source (see

page 23).

Changes the playback information displayed about the

song playing on the iPhone/iPod when DOCK is selected

as the input source (see page 26).

Playback information can only be displayed for an iPhone/iPod

that is connected using a Universal Dock for iPod.

6 MEMORY

Stores the current FM/AM station as a preset when

TUNER is selected as the input source (see page 20).

7 CLEAR

Clears the current FM/AM preset station when TUNER is

selected as the input source (see page 21).

8 Front panel display

Shows information about the operational status of this

unit.

9 PRESET j / i

Selects a preset FM/AM station when TUNER is selected

as the input source (see page 21).

0 FM, AM

Sets the FM/AM tuner band to FM or AM when TUNER

is selected as the input source (see page 17).

CONTROLS AND FUNCTIONS

Front panel

Note

CONTROLS AND FUNCTIONS

5 En

INTRODUCTION

English

A TUNING jj / ii

Selects the tuning frequency when TUNER is selected as

the input source (see page 17).

B Remote control sensor

Receives infrared signals from the remote control.

C PURE DIRECT and indicator

Allows you to listen to a source in the purest possible

sound (see page 14). The indicator above it lights up and

the front panel display turns off when this function is

turned on.

D PHONES jack

Outputs audio to your headphones for private listening.

Press SPEAKER A/B so that the SP A/B indicators turn off

before you connect your headphones to the PHONES jack.

E BASS control

Increases or decreases the low frequency response. The

center position produces a flat response (see page 14).

F TREBLE control

Increases or decreases the high frequency response. The

center position produces a flat response (see page 14).

G BALANCE control

Adjusts the sound output balance of the left and right

speakers to compensate for sound imbalances caused by

speaker locations or listening room conditions (see page

14).

H LOUDNESS control

Retains a full tonal range at any volume level to

compensate for the human ears’ loss of sensitivity to high

and low-frequency ranges at a low volume level (see page

15).

I INPUT selector

Selects the input source you want to listen to.

J VOLUME control

Increases or decreases the sound output level.

This does not affect the output level of the REC jacks.

Note

CONTROLS AND FUNCTIONS

6 En

1 SP (SPEAKERS) A/B indicators

Light up according to the set of speakers selected.

Both indicators light up when both sets of speakers are

selected.

2 Input source indicators

Light up brightly to indicate the input source that is

currently selected.

3 PRESET indicator

Lights up when you recall a preset radio station. Blinks

while the automatic station preset feature is scanning for

FM stations to register as presets.

4 MEMORY indicator

Lights up or blinks when an FM/AM station is being

stored as a preset.

5 TUNED indicator

Lights up when this unit is tuned in to an FM or AM

station.

6 STEREO indicator

Lights up when this unit is receiving a strong signal for an

FM stereo broadcast.

7 TP indicator

Lights up when this unit is tuned in to a Traffic Program

(TP) station. Blinks when searching for a TP station.

8 SLEEP indicator

Lights up when the sleep timer is turned on.

9 MUTE indicator

Blinks while the MUTE function is turned on.

0 P indicator

Lights up when a preset number is selected. Blinks while

you are registering a preset radio station.

A Multi-information display

Shows information when adjusting or changing settings.

B Volume indicator

Displays the current volume level.

Front panel display

CONTROLS AND FUNCTIONS

7 En

INTRODUCTION

CONTROLS AND FUNCTIONS

English

Rear panel

1 GND terminal

Used to connect a turntable (see page 10).

2 TAPE jacks

Used to connect a tape deck (see page 10).

3 Antenna terminals

Used to connect FM and AM antennas (see page 12).

4 DOCK jack

Used to connect an optional Yamaha Universal Dock for

iPod (such as the YDS-12), Wireless System for iPod

(YID-W10), or Bluetooth Wireless Audio Receiver

(YBA-10) (see page 25).

5 Power cable

For connecting this unit to an AC wall outlet (see page

12).

6 PHONO jacks

Used to connect a turntable (see page 10).

7 CD jacks

Used to connect a CD player (see page 10).

8 LINE 1-2 jacks

Used to connect audio components (see page 10).

9 SUBWOOFER OUT jack

Used to connect a subwoofer with built-in amplifier (see

page 10).

y

The SUBWOOFER OUT jack attenuates signals over 90 Hz.

0 POWER MANAGEMENT switch

Used to enable or disable the automatic power down

function. When this function is enabled, this unit

automatically enters standby mode if it is not operated for

a certain amount of time (3 settings are available; see page

32).

A SPEAKERS terminals

Used to connect speakers (see page 10).

B IMPEDANCE SELECTOR switch

Used to select the impedance setting (see page 11).

CONTROLS AND FUNCTIONS

8 En

This section describes the function of each button on the

remote control used to control this unit or a Yamaha CD

player.

■ Common controls

The following buttons can be used no matter which input

source is selected.

1 Infrared signal transmitter

Sends infrared signals.

2 A (power)

Turns this unit on, or sets it to standby mode.

This button functions only when the A (power) button on the

front panel is in the on position.

3 DIMMER

Changes the brightness level of the front panel display.

Choose brightness from 3 levels by pressing this button

repeatedly.

y

This setting is retained even if you turn off this unit.

4 SLEEP

Sets the sleep timer (see page 16).

5 Input selector buttons

Select the input source you want to listen to.

y

• The input source names correspond to the names of the

connection jacks on the rear panel.

• To select TUNER as the input source using the remote control,

press FM or AM.

6 OPTION

Turns the OPTION menu on and off (see page 30).

7 SPEAKERS A/B

Turns on and off the set of speakers connected to the

SPEAKERS A and/or SPEAKERS B terminals on the rear

panel of this unit when the corresponding button is

pressed.

8 MUTE

Mutes the sound output. Press again to restore the sound

output to the previous volume level.

9 VOLUME +/–

Increases or decreases the sound output level.

This does not affect the output level of the REC jacks.

0 RETURN

Returns to the previous menu or ends the menu display

when using the Option menu (see page 30).

A B / C / D / E / ENTER

Selects and confirms items in the Option menu (see page

30).

Remote control

Note

CONTROLS AND FUNCTIONS

9 En

INTRODUCTION

English

■ FM/AM controls

The following buttons can be used when TUNER is

selected as the input source.

B TP

Searches automatically for a station that provides traffic

program (TP) broadcasts (see page 24).

C PRESET j / i

Selects a preset FM/AM station when TUNER is selected

as the input source (see page 21).

D FM, AM

Selects TUNER as the input source and sets the FM/AM

tuner band to FM or AM (see page 17).

E INFO

Turns on and changes the Radio Data System display

mode when TUNER is selected as the input source (see

page 23).

■ iPod controls

The following buttons can be used when DOCK is

selected as the input source for listening to an iPhone/

iPod. For more information, see page 25.

0 REPEAT

A MENU/ Ee / b / a / ENTER

E INFO

F SHUFFLE

G B

H C

■ Yamaha CD player controls

The following buttons can be used to control a Yamaha

CD player when CD is selected as the input source.

I Yamaha CD player control buttons

• s Stops playback

• e Pauses playback

• p Starts playback

• DISC SKIP Skips to the next disc in a CD changer

• b Skips backward

• a Skips forward

• Ejects the disc

• w Rewinds playback

• f Fast-forwards playback

Even when using a Yamaha CD player, certain components and

features may not be available. Refer to your component’s owner’s

manual for more information.

■ Installing batteries ■ Operation range

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of this unit during

operation.

Note

Using the remote control

AA, R6, UM-3 batteries

Approximately

6 m (20 ft)

Remote control

CONNECTIONS

10 En

• Do not connect this unit or other components to the main power until all connections between components are

complete.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass. Refer to the owner’s manual for each of your components.

• Use RCA cables for audio components (except for speaker connections and DOCK jack connections).

• The IMPEDANCE SELECTOR must be set to the appropriate position before connecting speakers. See page 11 for

details.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the

speakers.

y

• The PHONO jacks are designed for connecting a turntable with an MM cartridge.

• Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise

without the GND connection.

CONNECTIONS

Connecting speakers and source components

CAUTION

Turntable

Audio

out

CD recorder,

etc.

DVD player,

etc.

Tape deck

GND

Audio

out

Speakers A

Subwoofer

For information about

other components that

can be connected to

this unit, see page 25.

Audio

in

Audio

out

Audio

out

Audio

in

Audio

out

Speakers B

CD player

PREPARATION

11 En

CONNECTIONS

PREPARATION

English

■ IMPEDANCE SELECTOR switch

Do not change the IMPEDANCE SELECTOR switch

while the power of this unit is turned on, as doing so may

damage the unit.

If the unit fails to turn on, the IMPEDANCE SELECTOR

switch may not be fully slid to either position. If this is the

case, remove the power cable and slide the switch all the

way to either position.

Select the switch position (LOW or HIGH) according to

the impedance of the speakers in your system.

■ Connecting speaker cables

When inserting speaker cables into the speaker terminals, insert

only the bare speaker wire. If insulated cable is inserted, the

connection may be poor and sound may not be heard.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section. A bi-wire

compatible speaker has four binding post terminals. These

two sets of terminals allow the speaker to be split into two

independent sections. With these connections, the mid and

high frequency drivers are connected to one set of

terminals and the low frequency driver to another set of

terminals.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, set the IMPEDANCE

SELECTOR switch to HIGH or LOW depending on the

impedance of your speakers:

8 Ω or higher: HIGH

4 Ω or higher: LOW

See page 11 for more information about the

IMPEDANCE SELECTOR switch.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker.

y

To use the bi-wire connections, press SPEAKERS A and

SPEAKERS B on the front panel or on the remote control so that

both SP A and B light up on the front panel display.

CAUTION

Switch

position

Impedance level

HIGH

• If you use one set (A or B), the impedance of

each speaker must be 8

Ω or higher.

• If you use two sets (A and B) simultaneously,

the impedance of each speaker must be 16

Ω

or higher.

• If you make bi-wire connections, the

impedance of each speaker must be 8

Ω or

higher. See page 11 for Bi-wire connection.

LOW

• If you use one set (A or B), the impedance of

each speaker must be 4

Ω or higher.

• If you use two sets (A and B) simultaneously,

the impedance of each speaker must be 8

Ω or

higher.

• If you make bi-wire connections, the

impedance of each speaker must be 4

Ω or

higher. See page 11 for Bi-wire connection.

Note

Remove

approximately

10 mm (3/8 in)

of insulation

from the end of

each speaker

cable.

CAUTION

Note

This unit

Speaker

SPEAKERS A/B

12 En

CONNECTIONS

Indoor antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should

provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center

about outdoor antennas.

■ Assembling the supplied AM loop

antenna

■ Connecting the wire of the AM loop

antenna

Plug the power cable into the AC wall outlet after all other

connections are complete.

Connecting the FM and AM antennas

Note

Indoor FM

antenna

(included)

Outdoor AM antenna

Use 5 to 10 m of vinyl-

covered wire extended

outdoors from a window.

Outdoor FM antenna

Ground (GND terminal)

For maximum safety and minimum interference, connect

the antenna GND terminal to a good earth ground. A

good earth ground is a metal stake driven into moist earth.

• The AM loop antenna

should always be connected,

even if an outdoor AM

antenna is connected to this

unit.

• The AM loop antenna

should be placed away from

this unit.

AM loop antenna

(included)

Connecting power cable

To the wall

outlet with the

power cable

PLAYING AND RECORDING

13 En

BASIC

OPERATION

English

Extreme caution should be exercised when you play back CDs encoded in DTS.

If you play back a CD encoded in DTS on a CD player that does not support DTS, only noise will be heard, and this noise

may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output

level of your CD player before you play back a CD encoded in DTS.

1 Press A (power) on the front panel inward to

turn on this unit.

2 Rotate the INPUT selector on the front panel

(or press one of the input selector buttons or

FM or AM on the remote control) to select the

input source you want to listen to.

3 Press SPEAKERS A and/or SPEAKERS B on

the front panel or on the remote control to

select speakers A and/or speakers B.

When speaker set A or speaker set B are turned on,

SP A or SP B is displayed on the front panel display

accordingly (see page 6).

• When one set of speakers is connected using bi-wire

connections, or when using two sets of speakers simultaneously

(A and B), make sure SP A and SP B are displayed on the front

panel display.

• When listening with headphones, turn off the speakers.

4 Play the source.

5 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote

control) to adjust the sound output level.

y

You can adjust the tonal quality by using the BASS, TREBLE,

BALANCE and LOUDNESS controls, or the PURE DIRECT

switch on the front panel (see page 14).

6 When finished listening, press A (power) on

the front panel outward to turn off this unit.

y

If A (power) on the remote control is pressed while the A (power)

button on the front panel is in the on position, this unit enters

standby mode. Press A (power) again to turn this unit on.

PLAYING AND RECORDING

CAUTION

Playing a source

A (power)

SPEAKERS A/B INPUT selector

VOLUME

A (power)

Input selector

buttons

SPEAKERS A/B

VOLUME +/–

FM, AM

Notes

BASIC OPERATION

14 En

PLAYING AND RECORDING

■ Using the PURE DIRECT switch

Routes input signals from your audio sources so that the

input signals bypass the BASS, TREBLE, BALANCE and

LOUDNESS controls, thus eliminating any alterations to

the audio signals and creating the purest possible sound.

The PURE DIRECT indicator lights up and the front panel

display turns off after a few seconds.

• The BASS, TREBLE, BALANCE, and LOUDNESS controls

do not function while the PURE DIRECT feature is turned on.

• This setting is retained even if you turn off this unit.

■ Adjusting the BASS and TREBLE

controls

The BASS and TREBLE controls adjust high and low

frequency response.

The center position produces a flat response.

BASS

When you feel there is not enough bass (low frequency

sound), rotate clockwise to boost. When you feel there is

too much bass, rotate counterclockwise to suppress.

Control range: –10 dB to +10 dB (20 Hz)

TREBLE

When you feel there is not enough treble (high frequency

sound), rotate clockwise to boost. When you feel there is

too much treble, rotate counterclockwise to suppress.

Control range: –10 dB to +10 dB (20 kHz)

■ Adjusting the BALANCE control

The BALANCE control adjusts the sound output balance

of the left and right speakers to compensate for sound

imbalance caused by speaker locations or listening room

conditions.

Adjusting the tonal quality

Notes

PURE DIRECT switch

BASS

TREBLE

BALANCE

15 En

PLAYING AND RECORDING

BASIC

OPERATION

English

■ Adjusting the LOUDNESS control

Retain a full tonal range at any volume level, thus

compensating for the human ears’ loss of sensitivity to

high and low-frequency ranges at low volume.

If the PURE DIRECT switch is turned on with the

LOUDNESS control set at a certain level, the input signals

bypass the LOUDNESS control, resulting in a sudden

increase in the sound output level. To prevent your ears or

the speakers from being damaged, be sure to press the

PURE DIRECT switch after lowering the sound output

level or after checking that the LOUDNESS control is

properly set.

1 Set the LOUDNESS control to the FLAT

position.

2 Rotate the VOLUME control on the front

panel (or press VOLUME +/– on the remote

control) to set the sound output level to the

loudest listening level that you would listen

to.

3 Rotate the LOUDNESS control until the

desired volume is obtained.

y

After setting the LOUDNESS control, enjoy listening to music at

your preferred volume level. If the effect of the LOUDNESS

control setting is too strong or weak, readjust the LOUDNESS

control.

CAUTION

LOUDNESS VOLUME

VOLUME +/–

16 En

PLAYING AND RECORDING

• The audio from the current input source is output to the TAPE

REC and LINE 1 REC jacks. When TAPE is selected, audio is

output to the LINE 1 REC jacks only. When LINE 1 is selected,

audio is output to the TAPE REC jacks only.

• This unit must be turned on in order to record.

• The VOLUME, BASS, TREBLE, BALANCE and

LOUDNESS controls and the PURE DIRECT switch have no

effect on the source being recorded.

• Check the copyright laws in your country before recording from

records, CDs, radio, etc. Recording copyright-protected

material may infringe on copyright laws.

1 Rotate the INPUT selector on the front panel

(or press one of the input selector buttons or

FM or AM on the remote control) to select the

source you want to record.

2 Play the source and begin recording using

the recording device connected to the REC

jacks (TAPE and/or LINE 1) on the rear panel.

See page 10.

Use this feature to automatically set this unit to standby

mode after a certain amount of time. The sleep timer is

useful when you are going to sleep while this unit is

playing or recording a source.

The sleep timer can only be set with the remote control.

1 Press SLEEP repeatedly to set the amount of

time before this unit is set to standby mode.

Each time you press SLEEP, the front panel display

changes as shown below.

The SLEEP indicator blinks while setting the amount

of time for the sleep timer.

If the sleep timer is set, the SLEEP indicator on the

front panel display lights up.

y

To cancel the sleep timer, do one of the following:

• Select “Sleep Off”.

•Press A (power) on the remote control to set this unit to standby

mode.

•Press A (power) on the front panel to turn off this unit.

Recording a source

Notes

INPUT selector

FM, AM

Input selector

buttons

Using the sleep timer

Note

A (power)

SLEEP

FM/AM TUNING

17 En

BASIC

OPERATION

English

There are 2 tuning methods; automatic and manual. Select either method according to your preference and the strength of

station signals.

Automatic tuning is effective when station signals are

strong and there is no interference.

1 Rotate the INPUT selector on the front panel

(or press FM or AM on the remote control) to

select TUNER as the input source.

If you press FM or AM on the remote control to select TUNER as

the input source, the corresponding band is also selected,

therefore you may skip step 2.

2 Press FM or AM on the front panel (or FM or

AM on the remote control) to select the

reception band (FM or AM).

FM or AM is displayed on the front panel display.

3 Press and hold TUNING jj / ii on the front

panel for more than 1 second to begin

automatic tuning.

Press ii to tune in to a higher frequency.

Press jj to tune in to a lower frequency.

• When you tune in to a station, the frequency of the station is

displayed on the front panel display.

• If the tuning search does not stop at the desired station because

the station signals are weak, try using the manual tuning

method.

■ Auto Mute feature

When listening to an FM radio station, the output will

automatically be muted when the radio signal is weak if

the station was tuned in to by:

• using the automatic tuning feature

• recalling a preset that was registered using the

automatic preset registration feature

If you want to listen to a station that has a weak signal,

tune in to the station manually.

FM/AM TUNING

Automatic tuning

Note

FM, AM

TUNING jj / ii

INPUT selector

FM, AM

Notes

18 En

FM/AM TUNING

Manual tuning is effective when station signals are weak.

1 Rotate the INPUT selector on the front panel

(or press FM or AM on the remote control) to

select TUNER as the input source.

If you press FM or AM on the remote control to select TUNER as

the input source, the corresponding band is also selected,

therefore you may skip step 2.

2 Press FM or AM on the front panel (or FM or

AM on the remote control) to select the

reception band (FM or AM).

FM or AM is displayed on the front panel display.

3 Press TUNING jj / ii on the front panel to

manually tune in to the desired station.

When you tune in to a station, the frequency of the received

station is shown in the front panel display.

■ Improving FM reception

If the signal from the station is weak and the sound quality

is not good, set the FM band reception mode to monaural

mode to improve reception.

1 Press OPTION on the remote control when

this unit is tuned in to an FM radio station.

The Option menu for TUNER is displayed (see page

30).

2 Press B / C on the remote control to select

“FM Mode”, and then press ENTER.

y

To cancel the operation and return to the Option menu, press

RETURN on the remote control.

3 Press D / E on the remote control to select

“STEREO” (automatic stereo mode) or

“MONO” (monaural mode).

• When MONO is selected, FM broadcasts will be

heard in monaural sound.

• When STEREO is selected and an FM station with

a stereo broadcast is tuned in, the broadcast will be

heard in stereo.

4 To exit the Option menu, press OPTION or

RETURN on the remote control.

The STEREO indicator on the front panel lights up while

listening to a station in stereo.

Manual tuning

Note

FM, AM

TUNING jj / ii

INPUT selector

FM, AM

Note

OPTION

RETURN

B / C / D / E

ENTER

Stránka se načítá...

Yamaha R-S300 Návod k obsluze

Související články

Jiné dokumenty