Hach 51 Series Uživatelský manuál

DOC024.98.93135

ORBISPHERE Model 51x

Analyzer with K-

M1100 sensors

04/2018, Edition 4

Basic User Manual

Allgemeines Benutzerhandbuch

Manuel d'utilisation de base

Manual básico del usuario

Základní uživatelská příručka

Allmän användarhandbok

Основно ръководство за потребителя

Alapvető felhasználói kézikönyv

Temel Kullanıcı Kılavuzu

English..............................................................................................................................3

Deutsch.......................................................................................................................... 22

Français......................................................................................................................... 43

Español.......................................................................................................................... 63

Čeština........................................................................................................................... 84

Svenska....................................................................................................................... 104

български................................................................................................................... 124

Magyar......................................................................................................................... 145

Türkçe...........................................................................................................................165

2

Specifications

Specifications are subject to change without notice.

Analyzer

Specification Details

Operating temperature –5 to 50°C (23 to 122 °F)

Storage temperature –20 to 70°C (–4 to 158 °F)

Operating humidity 0 to 95% non condensing relative humidity

Operating altitude From 0 to 2,000 m. (6,550 ft.) above sea level

EMC requirements EN61326-1: EMC Directive

Note: The wall mount instrument is a Class A product. In a domestic environment this product

may cause radio interference in which case the user may be required to take adequate

measures.

Korean registration

User Guidance for EMC Class A Equipment

업무용을 위한 EMC 등급 A 장치에 대한

사용자 지침

사용자안내문

A 급 기기 ( 업무용 방송통신기자재 )

이 기기는 업무용 (A 급 ) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의

하시기 바라며 , 가정외의 지역에서 사용하는 것을 목적으로 합니다.

CE compliance EN61010-1: LVD Directive

Safety rating ETL, conforming to UL 61010-1 and CSA 22.2 No. 61010-1

Enclosure ratings IP 65; Totally protected against dust; Protected against low pressure jets of water

from all directions.

NEMA 4X (wall mount only); Totally protected against dust; Protected against

pressure jets of water from all directions.

W A R N I N G

Enclosure rating does not apply to external power supply for benchtop

instruments.

Power supply Universal 100 VAC to 240 VAC @ 50/60 Hz - 40VA; 10 to 30 VDC - 30W

Analog current output version

on the measurement

board(s)

4-20 mA (default) or 0-20 mA (configuration with software);

3 configurable outputs: Maximum load: 500 ohm; Sensitivity: 20μA;

Accuracy: ± 0.5% (between operating temperature limits)

Analog voltage output

version on the measurement

board(s)

0- 5 V output (hardware option);

3 configurable outputs; Minimum load: 10 KOhm; Sensitivity: 5 mV;

Accuracy: ± 0.5% (between operating temperature limits)

Measurement alarm relays

on the measurement

board(s)

Three alarm relays per measurement board; 1A-30 VAC or 0.5A-50 VDC on a

resistance load.

Configurable to Normally Open [NO] or Normally Closed [NC] contacts by

changing the jumper positions.

W A R N I N G

Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC

RMS

English 3

Specification Details

System alarm relay on the

main board

One system alarm relay; 1A-30 VAC or 0.5A-50 VDC on a resistance load.

Normally closed [NC] (NO relay also available) when instrument is turned on.

W A R N I N G

Potential Electrocution Hazard. Connect only safety low voltage < 33 VAC

RMS

Thermal cut off Prevents ageing of sensors when exposed to high temperatures

Options USB host; Ethernet 10/100 Base-T

Wall and pipe mount

instrument

(H x D x W)

236.5 x 160 x 250 mm; Weight 4.25 kg

9.31 x 6.30 x 9.84 in.; Weight 8.82 lbs

Panel mount instrument

(housing) (H x D x W)

156 (123) x 250 x 220 (214) mm; Weight 3.35 kg

6.14 (4.84) x 9.84 x 8.86 (8.43) in.; Weight 6.62 lbs

K-M1100 sensor

Specification Details

Sample temperature Measurement from –5 to 50°C (23 to 122°F)

Sensor resistant to temperature from –5 to 100°C (23 to 212°F)

Sample pressure 1 to 20 bar absolute (14.5 to 290 psia)

Sample flow rate

requirement

50 to 300 mL/min

Sample types K1100 sensor: Water only

M1100 sensor (low range): Water and beer

M1100 sensor (high range): Water, beer, wine, wort and carbonated drinks

For oxygen measurement

in

liquid phase gas phase

Measurement range Low range sensors 0 to 2000 ppb (dissolved.

Indicative values until

5000 ppb)

0 to 50 mbar or 0 to 5% O

2

(at

atm pressure)

High range sensors 0 to 40 ppm (dissolved) 0 to 1 bar or 0 to 100% O

2

(at

atm pressure)

Repeatability Low range sensors ± 0.4 ppb or 1%,

whichever is the greater

± 0.01 mbar or 10 ppm gas or

1%, whichever is the greater

High range sensors ± 0.015 ppm or ± 2%,

whichever is the greater

± 0.4 mbar or 400 ppm gas or

2%, whichever is the greater

Reproducibility Low range sensors ± 0.8 ppb or 2%,

whichever is the greater

± 0.02 mbar or 20 ppm gas or

2%, whichever is the greater

High range sensors ± 0.02 ppm or ± 3%,

whichever is the greater

± 0.5 mbar or 500 ppm gas or

3%, whichever is the greater

Accuracy Low range sensors ± 0.8 ppb or 2%,

whichever is the greater

± 0.02 mbar or 20 ppm gas (at

atm pressure) or 2% of

reading, whichever is the

greater

High range sensors ± 0.02 ppm or ± 3%,

whichever is the greater

± 0.5 mbar or 500 ppm gas (at

atm pressure) or 3% of

reading, whichever is the

greater

4 English

Specification Details

Limit of detection

(LOD)

Low range sensors 0.6 ppb 0.015 mbar or 15 ppm gas (at

atm pressure)

High range sensors 0.015 ppm 0.4 mbar or 400 ppm gas (at

atm pressure)

Response time

(90%)

Low range sensors < 30 seconds < 10 seconds

High range sensors < 50 seconds < 10 seconds

Display resolution High and low range sensors 0.1 ppb 0.001 mbar or 1 ppm gas

Calibration Low range sensors: Single point calibration (zero)

High range sensors: Two at cap replacement (zero and air), one during use (air)

Calibration sample Low range sensors: Standard 99.999% N

2

(quality 50) or equivalent oxygen free gas

High range sensors: Standard 99.999% N

2

(quality 30) or equivalent oxygen free gas, air

M1100 12 mm (PG

13.5) sensor (L x W)

246 x 47 mm - weight 0.6 kg

9.69 x 1.85 in. - weight 1.32 lbs

K1100 and

M1100 28 mm

sensor (L x W)

143.50 x 49 mm - weight 0.74 kg

5.65 x 1.93 in. - weight 1.63 lbs

Calibration device Weight 0.7 kg

Expanded manual version

For additional information, refer to the expanded version of this manual, which is available on the

manufacturer's website.

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

English 5

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This is the safety alert symbol. Obey all safety messages that follow this symbol to avoid potential

injury. If on the instrument, refer to the instruction manual for operation or safety information.

This symbol indicates that a risk of electrical shock and/or electrocution exists.

This symbol indicates the presence of devices sensitive to Electro-static Discharge (ESD) and

indicates that care must be taken to prevent damage with the equipment.

This symbol, when noted on a product, indicates the instrument is connected to alternate current.

Electrical equipment marked with this symbol may not be disposed of in European domestic or

public disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no

charge to the user.

Products marked with this symbol indicates that the product contains toxic or hazardous substances

or elements. The number inside the symbol indicates the environmental protection use period in

years.

Operating altitude

This instrument is rated for an altitude of 2000 m (6562 ft) maximum. Use of this instrument at an

altitude higher than 2000 m can slightly increase the potential for the electrical insulation to break

down, which can result in an electric shock hazard. The manufacturer recommends that users with

concerns contact technical support.

Installation

This section provides necessary information to install and connect the analyzer. The installation of

the analyzer should be performed in accordance with relevant local regulations.

D A N G E R

Electrocution hazard. Do not connect AC power directly to a DC powered instrument.

6 English

D A N G E R

Electrocution hazard. Always remove power to the instrument before making electrical connections.

D A N G E R

Electrocution hazard. If this equipment is used outdoors or in potentially wet locations, a Ground Fault

Circuit Interrupt (GFCI/GFI) device must be used for connecting the equipment to its main power

source.

W A R N I N G

Potential Electrocution Hazard. A protective earth (PE) ground connection is required for both

100-240 VAC and 5 VDC wiring applications. Failure to connect a good PE ground connection can

result in shock hazards and poor performance due to electromagnetic interferences. ALWAYS connect

a good PE ground to the controller terminal.

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

N O T I C E

Install the device in a location and position that gives easy access to the disconnect device and its operation.

N O T I C E

Potential Instrument Damage. Delicate internal electronic components can be damaged by static electricity,

resulting in degraded performance or eventual failure.

Wall mounting

1.

Attach the U-bracket (provided) to the wall with two screws (not

provided).

2. Tilt the instrument slightly backwards to align the bracket pins and

the insertion slots, and slide the instrument onto the bracket as

shown.

3. Insert the 2 locking screws with washers through the side slots.

4. Adjust the instrument angle for better screen vision, and lock both

side screws.

Pipe mounting

1.

Assemble the pipe mount bracket to the U-bracket, using the two screws provided.

2. Attach this assembly to the pipe using two clamps (not provided).

3. Slide the instrument onto the bracket.

4. Insert the 2 locking screws with washers through the side slots.

5. Adjust the instrument angle for better screen vision, and lock both side screws.

English 7

Panel mounting

W A R N I N G

Electrocution hazard. If the cable and connector for the power supply are not accessible after

installation, an accessible local disconnection means for the instrument power is mandatory.

1-3 4-5 6-7

1. Cut an opening in the panel to accommodate the bracket frame provided.

2. Install the provided frame in the opening.

3. Fold the 6 tabs over the panel lips, using adjustable joint pliers.

4. Slide the instrument in the bracket frame. The instrument should go over the four "T" pins. Rotate the 4 fast

locking screws on both sides of the front panel and slide it in.

5. Rotate the 4 fast locking screws 1/4 turn twice in the lock direction as indicated on the side of the front panel.

This locks the instrument in place on the four "T" pins.

6. To access the connections inside the instrument, remove the instrument housing (six screws on the back

panel, and slide the housing back out)

7. Pass the cables through the housing, then through the cable gland (if applicable) and then perform the

connections as detailed below.

8 English

Instrument connections

Figure 1 Connections - panel (left); wall/pipe (right)

1 Power cable 6 K-M1100 LDO Sensor connection (2x)

2 Ethernet cable gland 7 External pressure sensor connection

3 USB-A host connector 8 Input/Output 2 cable gland

4 USB-B 4-pin connector 9 Keylock (wall/pipe mount only)

5 Input/Output 1 cable gland

Connection to mains power supply

Power supply connection (low voltage instruments)

For low voltage instruments (10-30 VDC), connection to the mains power supply is with a 8-pin

BINDER connector (supplied).

Note: The connectors are grooved to avoid an incorrect fitting to the instrument.

Connect the power cable to the connector as follows:

Figure 2 BINDER connector

Pin Connections:

1. Power 10-30 VDC

2. Ground

3. Ground

4. Ground

5. Not used

6. Power 10-30 VDC

7. Power 10-30 VDC

8. Earth

Figure 3 Wiring side view

Power supply connection (high voltage instruments)

D A N G E R

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

English 9

D A N G E R

Electrocution hazard. Always remove power to the instrument before making electrical connections.

High voltage instruments (100-240 VAC) have a 4-pin male connector pre-wired internally with a

male BINDER connector ready for mains connection. A compatible female connector is supplied with

the instrument.

If this female connector was supplied with a mains power plug already pre-attached (cable part

numbers 33031, 33032, 33033 and 33034) then the female connector can be plugged directly into

the instrument power connector. The two connectors are grooved to avoid an incorrect fitting. Tighten

the female connector to the instrument power connector finger-tight.

If no power cable was ordered with the equipment, a mains power plug must be connected to the

supplied female connector as described in the following procedure.

User-supplied power cable specifications:

• 3-wire (live, neutral and earth)

• cable Ø ≥ 7mm; ≤ 9.5mm

• wire selection ≥ 1mm

2

, AWG18; ≤ 2.5mm

2

, AWG14

Prepare the user-supplied power cable as follows:

1. Strip off 23 mm (0.9 ins.) of shielding from the power cable.

2. Cut back the live and neutral wires to 15 mm (0.6 ins.) in length but leave the earth wire as is.

3. Then strip off a small amount of external insulation from the three wires as required.

Wire the female connector as follows:

1. Take the narrow end of the connector (4) in one hand and the main body (2) in the other and

unscrew the two. Pull away the cable clamp (3) and unscrew the end plug (1) to reveal the four

parts that make up the connector.

2. Loosen the screws on the cable clamp (3) to allow enough room to pass the power cable through.

3. Pass the power cable through the end plug (1), the main body (2), and the cable clamp (3), and

then connect the three wires (live, neutral and earth) to the connector (4) as follows:

1. Live (brown)

2. Neutral (blue)

3. Not used

Earth - Earth (green and yellow)

Note: The numbers and earth symbol are stamped on the end of the connector. Ensure it is connected

correctly.

4. Slide the cable clamp (3) back onto the connector (4) and tighten the screws on the clamp to

secure the cable.

5. Screw the two parts (4) and (2) back together.

6. Secure the power cable by screwing the end plug (1) back in place.

7. The female connector can now be plugged directly into the instrument power connector. The two

connectors are grooved to avoid an incorrect fitting. Tighten the female connector to the

instrument power connector finger-tight.

10

English

Connections to electronic boards

N O T I C E

Potential Instrument Damage. Delicate internal electronic components can be damaged by static electricity,

resulting in degraded performance or eventual failure.

Note: Any loose connection wires should be bundled tightly together with the use of nylon cable ties.

Sensor cable

An ORBISPHERE cable (10 wire shielded, Part N° 32505.mm) is needed to connect the sensor(s) to

the instrument. The instruments have a Lemo 10 socket on the back panel where the sensor cable

has to be connected.

Electronic boards connectors

Connectors P8 on the main board (Figure 4 on page 11) and J7 on the measurement board (refer

to Measurement board on page 12) are made of two parts. Push down carefully the black levers on

either side of the connector and pull it out securely. Perform all connections with these connectors

unplugged. Once finished, attach the connectors to the boards by pushing them firmly in place

(levers up).

Main board

Figure 4 Main board

Figure 5 Connector P8

Connector P8

The numbers listed below refer to the 13 available P8 connections (from left to right) in Figure 5.

1. RS-485 (signal A)

2. RS-485 (signal B)

3. PROFIBUS-DP (GND)

4. PROFIBUS-DP (+ 5 V)

5. PROFIBUS-DP (signal -)

6. PROFIBUS-DP (signal +)

7. PROFIBUS-DP (signal RTS)

8. Not used

9. Not used

10. Not used

11. System alarm relay (N.O.)

12. System alarm relay (N.C.)

13. System alarm relay (Common)

Connector P3

Ethernet RJ 45. Connect the instrument to the local network by passing an ethernet cable through

the ethernet cable gland (refer to Instrument connections on page 9) and connecting to the

P3 connector illustrated in Figure 4.

English

11

Measurement board

Figure 6 Measurement board

Figure 7 Connector J7

Connector J7 (inputs & outputs)

The numbers listed below refer to the 16 available J7 connections (from left to right) in Figure 7.

Measurement alarms relays:

1. Common

2. Output relay 1

3. Output relay 2

4. Output relay 3

Analog current

outputs:

5. Analog GND

6. Output 1

7. Output 2

8. Output 3

Digital inputs:

9. Hold input. To deactivate the sensor from a PLC system, connect a dry contact

between J7.9 and J7.12

Note: It is recommended to use this functionality in order to extend the sensor lifetime for

installations with a CIP process that can damage the spot.

10. to 11. Not used

12. Digital GND

13. to 16. Not used

Measurement alarm relays

The three output relays are located on the measurement board.

They can be individually configured to Normally Open (NO) or to Normally Closed (NC) by

physically moving the jumper on each relay. On the illustration:

• Upper relay is set to NC

• Middle relay is set to NO

• Lower relay is shown with no jumper

Note: J14 is relay 1, J18 is relay 2, J19 is relay 3

Note: The output relays are in alarm condition when the instrument power is set to off.

12 English

Sensor installation

Sensor positioning

The sensor must be installed in a socket or flow chamber that allows contact with the sample fluid to

be analyzed. The sensor and measuring instrument are connected by a cable. The standard sensor

cable lengths are 3, 5, 10, 15 and 20 meters. Ensure that the sensor will be mounted:

• perpendicular to the pipe

• on a horizontal pipe section (or on flow-ascending vertical pipe)

• minimum of 15 meters away from the pump's discharge side

• in a place where the sample flow is stable and rapid, and as far as possible from:

• valves

• pipe bends

• the suction side of any pumps

• a CO

2

injection system or similar

Note: There may be situations where not all the above conditions can be met. If this is the case, or you have any

concerns, please consult your Hach representative to appraise the situation and define the best applicable solution.

User interface

Instrument controls

The instrument front panel provides:

• A touch screen acting as display, touch pad and keyboard.

• A LED, showing when the instrument is on.

Turning instrument On and Off

There is no power switch on the instrument. The mains must be disconnected to turn the instrument

off.

Measurement window

The main (numeric) measurement window continuously displays:

• Sensor measured values

• Measured sensor trends (for the last 10 minute to last hour)

• Measured sensor data alarm limits and other events

• Temperature

Touch screen

The user interface on the front panel is a touch screen providing easy selection through menus. All

the measurement, configuration, calibration and standard service routines can be called by pressing

buttons and menu bars on screen.

The display can be configured to only show a sensor measurement, or to show a parameterized

graphic representation of the last measurements.

English

13

Menu navigation

Pressing the “menu” button in the header bar calls the main menu. The

display is made of three columns:

• The left shows the menu options

• The center shows a tree view of the position inside the menu

structure

• The right has the following generic controls:

• Up - Return to previous menu (one step back)

• Main - Jump directly to main menu

• Close - Close the menu and go back to the measurement display.

• Help - Help topics concerning current menu

Virtual keyboard

When a value or text is to be edited a virtual keyboard will appear on screen and can be used like a

standard keyboard. Press CAP to access special keys. When input is complete press the Enter key

to confirm and exit the virtual keyboard. During editing, the edited field name is displayed along with

units where applicable.

Security menu

Note: When the instrument is started for the first time security is disabled. It is highly recommended that each user

be entered into the system and given appropriate access rights as soon as possible to avoid any unauthorized

access.

Configure security

Define access levels for all users . This requires a user access level 4.

1. Select Configuration from the Security menu.

Option Description

Access rights When enabled only registered users can access the menus. When disabled (default)

all menus are freely accessible and no ID is recorded against any action in the log file.

Max session time The user is logged out automatically when the time limit is reached.

User action logging When enabled every action from a logged on user is recorded in a user log file.

User action log file The log file is a rolling buffer recording recent actions. Press Clear to empty the log

file.

User management

Select Access table from the Security menu to show the list of registered users (a maximum of

99 users allowed). They are listed by name, ID, password and access level.

Pressing on an empty line or the Add button displays a window to add a new user. User name, ID,

password (minimum 4 characters) and access level (1 to 4) are required.

Pressing on a registered user displays a window for editing or deleting that user.

View menu

Numeric view

This is the default view. Display shows the numeric measurement value identified for each gas

measurement channel used, a graphic showing measurement value evolution during the set time

frame, and sample temperature. The display is refreshed after each measurement cycle ( based on

14

English

the oxygen level for LDO sensor). This display can be configured to suit individual conditions and

convenience.

The K-M1100 low range sensors measure dissolved oxygen up to a maximum value of 5000 ppb.

Below 2000 ppb the measurement cycle interval is 4 seconds for 2 channels and 6 seconds for

3 channels. Between 2000 and 3000 ppb the measurement cycle interval is 30 seconds. Above

3000 ppb the measurement cycle interval is 60 seconds. The K-M1100 high range sensors

measure dissolved oxygen up to a maximum value of 40 ppm, the measurement cycle interval is

4 seconds for 2 channels and 6 seconds for 3 channels. Should the measured concentration go

above the maximum value for the sensor then the measurement cycle is increased to 60 seconds

and an Out of range message will be displayed. An arrow symbol to the right indicates if the value is

increasing, decreasing, or remaining constant. Once the measured value falls below the maximum

value, the measurement cycle returns to the pre-defined interval.

Numeric view configuration

1. Select Configure from the View menu followed by Conf. numeric view to customize the display:

Option Description

Display temperature Select Channel x to display the sample temperature for that channel.

Display channel 1, 2, 3 Select yes or no

Display mini graph Check the box to display the graph.

Display time base Check the box to display the time base.

Upper bound Adjust graph upper limit.

Lower bound Adjust graph lower limit.

Time base Adjust graph time span.

Grid button Set up the graph to display the x or y axes, grid, or alarm thresholds.

Auto scale update button Automatically set the graph upper and lower bounds to best fit the actual values

displayed.

Clean button Clear the graph being displayed and restart.

Statistic view

This feature offers statistical data to match with Total Quality Management tools to better analyze

how a process behaves. The statistics are calculated from the data in the measurement file and

values updated each time a new measurement is added.

Diagnostic view

The diagnostic view contains important information but is only really useful for troubleshooting

purposes.

Measurement menu

Instrument configuration

1. Select Config. instrument from the Measurement menu:

Option Description

Measurement mode Continuous mode for on line process. Default: Continuous mode.

Sample mode for lab sample analysis of small individual samples, such as cans or

bottles.

English 15

Option Description

Pressure Select the barometric pressure units.

Temperature Select the temperature units.

Measurement configuration

K-M1100 sensor configuration

1. Select Configure channel from the Measurement menu:

Option Description

Sensor Selec the sensor model H or L

Medium Select Liquid or Gas.

Gas unit type Select Partial, Fraction, or Dissolved.

Gas unit When a composite unit is selected the unit will change depending on the range of the

value to display. The list of available units depends on the gas unit type selected.

Liquid For the K1100 sensor this option is locked on Water. For the M1100 low range sensor,

choose between Water and Beer. For the M1100 high range sensor, choose between

Water, Beer, Wort, Wine and Carbonated drink.

Display resolution A maximum of 5 digits can be displayed. Decimals can be limited to 0, 1, 2 or 3 for

easier reading. The resolution affects only the data displayed, not the resolution of data

measured and stored.

T cut off If this temperature is exceeded the measurement session is suspended and the system

displays a HOT alarm message. The system resumes when the temperature drops to

90% of the specified temperature. It is recommended to Enable this feature to maximize

sensor life and system performance.

T cut off value Set to 5°C above the sample temperature.

K-M1100 advanced configuration

Note: The offset feature described below should be used for minor measurement adjustments only, and not as an

alternative to a sensor calibration. Make sure your sensor has been correctly calibrated before applying this feature.

1. Select the Advanced button on the Measurement configuration screen:

Option Description

Offset enabled Check this box to enable the user measurement offset option. If checked enter an

offset value or a target value:

Offset value Enter an offset value to manually adjust the measurement value. If the gas unit type or

gas unit (defined in the Measurement configuration screen) are changed the offset

value is automatically reset to zero.

Measurement This field cannot be updated. It shows the current measurement value with the offset

applied.

Target value Enter a target measurement value. The offset value is automatically computed so the

displayed measurement value will be equal to the target value.

Compute offset Select this button to recompute the offset value at any time during the measurement

process. The offset value will be computed based on the current and target

measurement values.

Out of range

protection

Check this box to enable the out of range protection (recommended). When enabled

and the measured value exceeds the instrument specification, the measurement

interval will be increased to 1 minute to protect the lifetime of the sensor spot. If

disabled, the lifetime of the spot can be negatively impacted if the sensor is exposed

to high oxygen concentrations for long periods of time.

16 English

Option Description

Measurement

interval

Set the value to between 2 and 60 seconds to define the interval for refreshing the

measurement value on the display.

Note: The minimum value for the measurement cycle interval is 4 seconds for

2 channels and 6 seconds for 3 channels

Hold recovery time This parameter defines the interval during which the outputs remain frozen after the

measurement is no longer on HOLD. Set the value to between OFF and 10 minutes,

according to the timing of your setup.

Measured data storage

There is one measurement file per channel which contains the data generated by the measurement

cycle.

1. Storage modes:

Option Description

No storage Storage is disabled.

Store once When the volatile memory is full (10,000 positions), the recording of measurement stops.

Rolling buffer When the volatile memory is full, the latest measurement set replaces the oldest one

continuously (first-in, first-out).

Calibration

Calibrations can only be performed once the instrument has been installed and configured.

Note: The temperature sensor is factory calibrated and can only be changed by a Hach representative.

K-M1100 sensor calibration

Sensor calibration

The sensor can be calibrated manually on an ad hoc basis. By default, the mode is set to zero

calibration with auto-end.

For higher level concentrations (above 1% oxygen which corresponds to about 400 ppb dissolved

O

2

) a high level adjustment can be performed using a gas mixture containing more than 1% oxygen,

or a known line sample. However, this should not be done without first ensuring the zero point is

accurate. This can be achieved by performing a zero calibration first.

Low range sensors: (K-M1100-L spots)

There are two calibration modes available - zero or high level adjustment. The sensor is factory

calibrated at zero. During use, the zero calibration is the best calibration to guarantee the sensor

specifications. After a spot replacement, a zero calibration is recommended.

High range sensors: (K-M1100-H spots)

There are three calibration modes available - zero, high level adjustment or in 100% humid air. The

sensor is factory calibrated at zero and in 100% humid air. During use, humid air calibration is the

best calibration to guarantee the sensor specifications. After a spot replacement, a zero calibration

and a 100% humid air calibration are recommended.

Initial sensor calibration

The sensor has been calibrated at the factory prior to shipment and is ready for use upon delivery.

However, if the sensor has not been used for a period of more than six months since delivery or if the

sensor spot has been replaced or changed in any way, then a sensor calibration will be required.

English

17

1. From the Main menu, select Calibration followed by Gas sensor and then Configuration. Make

sure the parameters are set as follows:

Option Description

Auto-calibration Not available for this sensor.

Manual-calibration Make sure that the Auto-End box is checked.

Hold during calibration or

verification

Make sure this box is checked.

Zero calibration bottle Make sure this is disabled by unchecking the box as it is not relevant

for this sensor.

2. Exit from the configuration screen by pressing OK.

3. Select Calibration and perform a manual zero calibration as described in Zero calibration

on page 19. For high range sensors perform an additional 100% humid air calibration as

described in 100% humid air calibration (high range sensors only) on page 19.

Manual calibration

Manual calibrations can be made at any time by following these steps:

1. Remove the sensor from the sample line.

2. Rinse the sensor head with clean water.

3. Wipe the sensor head with a clean soft tissue to remove any excess moisture.

4. If using the supplied calibration device insert the sensor into the sensor holder on top of the

calibration device. If not using the calibration device insert the sensor into the flow chamber.

5. Flow the calibration sample through the calibration device or flow chamber as applicable. If using

the calibration device fully open the valve on the pressure reducer to give a gas flow rate of

0.1 L/min. If you are not using the supplied calibration device with pressure reducer the maximum

allowable inlet pressure must be no more than 2 bar absolute.

Note: The manufacturer recommends to keep the flow chamber at atmospheric pressure. Adjust the sample

flow before it goes into the flow chamber.

6. Configure the calibration as described in Calibration configuration on page 18.

7. Start the calibration as described in Zero calibration on page 19, 100% humid air calibration

(high range sensors only) on page 19 or High level adjustment on page 20 depending on the

preferred calibration method.

Calibration configuration

Note: This option can also be invoked by pressing the Modify button in either the Zero calibration or High level

adjustment calibration screens.

1. From the Main menu, select Calibration followed by Gas sensor and then Configuration.

Option Description

Auto-calibration Not available for this sensor.

Manual-calibration When Auto-End is enabled a manual calibration will complete automatically when the

parameters defined in Stop parameters are reached. Press on Configure to set the

manual calibration parameters. If the calibration fails, the previous calibration

parameters remain unchanged and a warning message displayed.

Hold during

calibration or

verification

If checked this keeps the last measured value and stops updating the outputs during

the calibration or verification process. This avoids sending invalid information to any

connected device. At the end of a calibration, this hold remains on for a further

10 minutes to allow the system to stabilize.

18 English

Option Description

Zero calibration

bottle

Make sure this is disabled by unchecking the box as it is not relevant for this sensor.

Stop parameters If this button is pressed you can view or change the existing values or restore the

default values. It is highly recommended to leave these parameters at their default

values. These values apply to manual calibrations with the Auto-End parameter

enabled.

Configure manual calibration

1. Set the parameters for a manual sensor calibration:

Option Description

Calibration mode Select Zero calibration or High level adjustment. If using a high range sensor you also

have the option of 100% humid air calibration.

Note: If zero calibration or 100% humid air calibration is selected, no other parameters

are required. The following are only required for high level adjustment.

Cal. sample Set to In line sample, Gas bottle or Factory parameters. If factory parameters is

selected, the Ksv value is displayed but can be changed.

These additional parameters are required if in line sample or gas bottle has been

selected as the calibration sample:

Medium This is automatically set to Liquid if in line sample has been selected as the calibration

sample, or Gas if gas bottle has been selected.

Gas unit type Either Partial or Dissolved are available for an in line sample. If gas bottle was selected

this is set to Fraction.

Gas unit The list of available units depends on unit type selected above.

Liquid Select Water for the for the K1100 sensor (default) or Beer for the M1100 sensor.

Reference value Enter the reference value for calibration.

Zero calibration

With this method, the sensor should be removed from the sample and exposed to pure N

2

gas. It is

recommended to use the specially designed portable calibration device for this purpose.

Press Start to start the calibration.

A screen is displayed showing the measured values and length of time the sensor has been under

calibration. These values are continually refreshed.

The value % last calibration is an informational message showing the difference between the

current and previous sensor calibrations.

The Signal within range and Stability reached boxes indicate whether the calibration is within

acceptable limits. When both boxes indicate YES, press Finish to accept the new calibration. If one

or both boxes continue to show NO you can still perform a calibration but it is not recommended

and the calibration should be aborted by pressing the Cancel button.

In the case of a calibration failure, attempt a second calibration after about 5 minutes. If the second

attempt also fails, then refer to your Hach representative for advice.

Note: If the Auto-End parameter is enabled then the calibration will be considered successful when the parameters

defined in Stop parameters are met.

If you have not accepted or cancelled the calibration after an elapsed time of 10 minutes then the

process will time-out.

100% humid air calibration (high range sensors only)

With this method, the sensor should be removed from the sample and exposed to air saturated with

humidity. Do this by putting a drop of water in the calibration cap before installing the cap on the

sensor. Press Start to start the calibration. The process is then the same as for the Zero calibration

described previously.

English

19

High level adjustment

Note: Before using this option, ensure a zero calibration has been successfully completed first.

This calibration exposes the sensor to a gas or a liquid sample with a known gas concentration. You

also have the option to reset the sensor’s calibration parameters to factory settings (from drop-down

list for Cal. sample).

Press Start to start the calibration. The process is then the same as for the Zero calibration

described previously.

Barometric pressure calibration

Note: The barometric pressure sensor has been factory calibrated but should be periodically verified with a

precision certified barometer. The barometric pressure is necessary for the O2 sensor calibration. Make sure that

the barometric pressure is correct before the sensor calibration. If necessary, calibrate the barometric pressure.

The upper box shows the barometric pressure as measured by the instrument.

Using a precision certified barometer measure barometric pressure in the location where the

measuring instrument is used. Compare the values and if they are the same press Cancel, otherwise

enter the new barometric pressure value in the lower box and press Validation to validate the new

setting.

Other menus

For information on setting up relays and analog outputs refer to the full user manual (Inputs/Outputs

menu).

For information on setting up RS485, PROFIBUS-DP, USB, HTTP/TCP-IP and attached PRINTER

links refer to the full user manual (Communications menu).

For information on setting up products and global configurations refer to the full user manual

(Products and Global Configuration menus).

Maintenance

Instrument maintenance

C A U T I O N

Personal Injury Hazard. Any instrument maintenance should be carried out by a qualified Hach Service

Technician. Please contact your local representative should you feel any maintenance or instrument adjustments

are required.

Sensor maintenance

The sensor spot needs to be replaced about once a year. The procedure is very simple and takes no

more than a couple of minutes. Based on the measurement range of oxygen, the sensor lifetime can

be shorter and the maintenance—and calibration—frequency increased. If there are bleaching

compounds and strong oxidants (e.g., ClO

2

) in the sample, the sensor lifetime can also be shorter.

Equipment required

1.

A replacement sensor spot

2. The maintenance tool delivered with the sensor

3. O-ring supplied with the sensor spot

20 English

Stránka se načítá ...

Hach 51 Series Uživatelský manuál

Hach 51 Series Uživatelský manuál

v jiných jazycích

Související papíry

Jiné dokumenty